Details, datasheet, quote on part number: MAX2769CEVKIT#
TitleGPS Development Tools Eval Kit for MAX2769CETI+

Maxim MAX2769C Universal GNSS Receiver is a next-generation Global Navigation Satellite System (GNSS) receiver. This receiver covers L1/E1, B1, G1 bands for GPS, Galileo, BeiDou, and GLONASS satellite systems on a single chip. This single-conversion GNSS receiver is designed to provide high performance for an industrial and wide range of consumer applications, including mobile handsets. Designed on Maxims advanced, low-power SiGe BiCMOS process technology, the MAX2769C offers the highest performance and integration at a low cost. Incorporated on the chip is the complete receiver chain. The receiver includes a dual-input LNA and mixer, followed by the image-rejection filter, Programmable Gain Amplifier (PGA) and a multibit ADC. The total cascaded noise figure of this receiver is as low as 1.4dB. In addition, the device includes an integrated VCO, a crystal oscillator, a fractional-N frequency synthesizer to program the LO frequency using different reference frequencies.

CompanyMaxim Integrated Products
DatasheetDownload MAX2769CEVKIT# datasheet
MAX2769CEVKIT# photo

Others parts numbering
MAX2769CETI+: RF Receiver Universal GPS Receiver


Features, Applications


The MAX2769/MAX2769B/MAX2769C evaluation kit (EV kit) simplifies evaluation of the MAX2769/MAX2769B/ MAX2769C universal GPS receiver. It enables testing of the device performance and requires no additional support circuitry. Standard 50 SMA connectors are included on the EV kit for the inputs and outputs to allow for quick and easy evaluation on the test bench. The evaluation kit is fully assembled and tested at the factory. This document provides a component list, a list of equipment required to evaluate the device, a straightforward test procedure to verify functionality, a description of the EV kit circuit, the circuit schematic, and artwork for each layer of the printed circuit board (PCB).

Easy Evaluation of the to +3.3V Single-Supply Operation 50 SMA Connector on the RF Ports and for the Baseband Outputs All Critical Peripheral Components Included Parallel Port for 3-Wire Interfacing PC Control Software Available Upon Request

PART TYPE MAX2769EVKIT+ EV Kit MAX2769BEVKIT# EV Kit MAX2769CEVKIT# EV Kit +Denotes lead-free and RoHS compliant. #Denotes RoHS compliant. DESIGNATION J12 J9 QTY 9 DESCRIPTION SMA end-launch jack receptacles, 0.062in Johnson x 5 dual inline header, 100-mil center Sullins PEC36DAAN DB25 right-angle male connector AMP 5747238-4 Not installed, inductors Not installed, resistors

100pF 5% capacitors (0402) Murata 10F 10% tantalum capacitors (B case) AVX 0.01F 10% capacitors (0402) Murata 27pF 5% capacitor (0402) Murata 6800pF 10% capacitors (0402) Murata 470pF 10% capacitor (0402) Murata GRM155R71H471K Not installed, capacitors 10pF 5% capacitors (0402) Murata 1.0F 10% capacitors (0402) Murata GRM155R60J105K

20k 5% resistors 10k 1% resistors 47.5 1% resistors 75 1% resistors 22.1 1% resistor 100k 1% resistor (0402) Not installed PC mini-red test points Keystone 5000

DESIGNATION U12, U18 QTY DESCRIPTION MAX8510EXK29+ ultra-low-noise, high PSRR, low-dropout, 120mA linear regulators 16.368MHz TCXO Rakon IT3205BE Not installed MAX4444ESE+ ultra-high-speed, low-distortion, differential-tosingle-ended line receivers MAX4447ESE+ 6500V/s wideband, high-output-current, single-ended-to-differential line driver MAX2769ETI+ low-power, singleconversion, low-IF GPS receiver

DESCRIPTION SN74LV07ADR hex buffer/driver with open-drain output Texas Instruments x 2 inline headers, 100-mil center Sullins x 3-inline headers, 100-mil center Sullins PEC36SAAN Not installed Shorting jumpers, gold finish contact W23, W28) Sullins SSC02SYAN

SUPPLIER AVX Corp. Murata Mfg. Co., Ltd. Rakon Ltd. Texas Instruments WEBSITE

Note: Indicate that you are using the MAX2769/MAX2769B/MAX2769C when contacting these component suppliers.

The MAX2769/MAX2769B/MAX2769C EV kit includes two on-board MAX8510 linear regulators for powering up the MAX2769/MAX2769B/MAX2769C device to a regulated supply voltage of +2.85V. When using the linear regulators, connect pins 1-2 of jumpers W16 and W17. The MAX2769/MAX2769B/MAX2769C can also be powered directly through an external power supply through pin 2 of the jumpers (see Figure 1 for details).

An RF spectrum analyzer that covers the MAX2769/ MAX2769B/MAX2769C operating frequency range (e.g., FSEB20, or equivalent) A power supply capable to +6V One ammeter for measuring the supply current (optional) 50 SMA cables A network analyzer (e.g., 8753D or equivalent) to measure small-signal return loss (optional) A dual power supply capable of delivering 5V A user-supplied IBM-compatible PC Oscilliscope or logic analyzer to measure digital outputs (optional)

This section lists the recommended test equipment to verify operation of the It is intended as a guide only and some substitutions are possible. One RF signal generator capable of delivering at least +5dBm of output power at the operating frequency (e.g., E4433B or equivalent)

This section provides the EV kit and testing not turn on the DC until all connections

defaults, also set the SHDN and IDEL pins to 1, under "Entry" page, Hardware Control section. Upon device power-up, the default state should set the MAX2769 device in automatic-gain-control mode (AGCMODE = 00, PGAIEN = 1, and PGAQEN = 0). The default configuration will set the center frequency to 3.9MHz and a bandwidth of 2.5MHz. Using the control software, configure the following: a) In the "Entry" page of the graphical user interface (GUI), set the reference frequency 16.368MHz. b) Set the R divider to 16. c)Enable the I and Q channels by setting the IQ enable 1. d) Set the "output level" 1X = analog outputs through the "Entry" page or configuration register 2. 12)Activate the RF generator and observe the IF signal at an I_OUT_ANA SMA connector J3. 13)Set the "output level" 00 = CMOS logic through the "Entry" page and observe the ADC digital output at J9AJ9D header pins.

a step-by-step guide to operating the device functions. Caution: Do power or RF signal generators are completed.

1) Connect the PC to the INTF3000 interface board using the USB cable. On the INTF3000, remove jumper JU1, and connect a DC supply set +3V to the VPULL connector. Connect the 25-pin connector of the INTF3000 (J4) directly to the 25-pin connector of the EV kit (JDR1). 2) Connect a DC supply set to +3V (through an ammeter if desired) to jumpers W19 and W20 on the EV kit. Do not turn on the supply. When using the on-board linear regulators to power the MAX2769/MAX2769B/ MAX2769C, connect pins 1-2 of jumpers W16 and W17. 3) Connect a DC supply set +5V to jumper W12 on the EV kit. Connect a DC supply set -5V to jumper W11 on the EV kit. Do not turn on the supply. 4) Make sure that jumpers W1W9 and W18 are shorted for proper supply connection. 5) Leave jumpers W14, W15, and W28 open and connect jumper W23 to ground (pins 1-2) if the MAX2769/MAX2769B/MAX2769C is evaluated using a 3-wire bus. 6) Set the signal generator -110dBm. Do not turn on the generator's output. Connect the RF signal generator to the LNA1 input. 7) Connect LNA_OUT SMA connector (J8) to the MIX_IN SMA connector (J12) on the EV kit. 8) Connect the output of the MAX4444 buffer (connector J3) on the EV kit to a spectrum analyzer. 9) Turn on the DC supply. The supply current should read approximately 20mA. 10)Visit HERE to download the latest version of the EV kit software, Max2769A_Setup_2-0-1.exe (for MAX2769EVK), Max2769B_Setup_2-0-1.exe (for or MAX2769C_Setup_1.0.0.exe (for MAX2769CEVK). Run the installation file. 11)Run the control software on an IBM-compatible PC. Load the default state by clicking Settings, then

A good PCB is an essential part an RF circuit design. The EV kit PCB can serve as a guide for laying out a board using the devices. Keep traces carrying RF signals as short as possible to minimize radiation and insertion loss. Use impedance control on all RF signal traces. The exposed paddle must be soldered evenly to the board's ground plane for proper operation. Use abundant throughputs beneath the exposed paddle and between RF traces to minimize undesired RF coupling. To minimize coupling between different sections of the IC, each VCC pin must have a bypass capacitor with low impedance to the closest ground at the frequency of interest. Do not share ground vias among multiple connections to the PCB ground plane. Refer to the Layout Issues section of the MAX2769/MAX2769B/MAX2769C IC data sheet for more information.


Some Part number from the same manufacture Maxim Integrated Products

Maxim MAX2769C Universal GNSS Receiver is a next-generation Global Navigation Satellite System (GNSS) receiver. This receiver covers L1/E1, B1, G1 bands for GPS, Galileo, BeiDou, and GLONASS satellite


MAX5176A : Low-Power, Serial, 12-Bit DACs With Voltage-output

MAX8712ETG : Low-Cost, Linear-Regulator LCD Panel Power Supplies The MAX8710/MAX8711/MAX8712 offer complete linear-regulator power-supply solutions for thin-film transistor (TFT) liquid-crystal-display (LCD) panels used in LCD monitors and LCD TVs. All three devices include a high-performance AVDD linear regul

MAX6715AUTTID6+ : Dual/Triple, Ultra-Low-Voltage, SOT23 P Supervisory Circuits The MAX6715AMAX6729A/MAX6797A are ultra-low-voltage microprocessor (??P) supervisory circuits designed to monitor two or three system power-supply voltages. These devices assert a system reset if any monitored supply falls below its fac

MAX6786TA+T : Pmic - Battery Management Integrated Circuit (ics) Tape & Reel (TR) 1.2 V ~ 5.5 V; IC BATT MON DUAL .5% 8TDFN Specifications: Battery Chemistry: Alkaline, Li-Ion, NiCd, NiMH ; Function: Battery Monitor ; Package / Case: 8-WDFN Exposed Pad ; Packaging: Tape & Reel (TR) ; Operating Temperature: -40C ~ 85C ; Voltage - Supply: 1.2 V ~ 5.5 V ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

MAX6441KAAGWD3+T : Pmic - Battery Management Integrated Circuit (ics) Tape & Reel (TR) 1 V ~ 5.5 V; IC BATTERY MON DUAL SOT23-8 Specifications: Battery Chemistry: Alkaline, Li-Ion, NiCd, NiMH ; Function: Battery Monitor ; Package / Case: SOT-23-8 ; Packaging: Tape & Reel (TR) ; Operating Temperature: -40C ~ 85C ; Voltage - Supply: 1 V ~ 5.5 V ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

MAX6868UK40D2S+T : Pmic - Supervisor Integrated Circuit (ics) Simple Reset/Power-On Reset Tape & Reel (TR) 1; IC MPU SUPERVISOR SOT23-5 Specifications: Output: Push-Pull, Totem Pole ; Reset: Active High ; Package / Case: SC-74A, SOT-753 ; Packaging: Tape & Reel (TR) ; Number of Voltages Monitored: 1 ; Reset Timeout: 40 ms Minimum ; Type: Simple Reset/Power-On Reset ; Voltage - Threshold: 4V ; Operating Temperature: -40C ~ 85C

MAX6792TPZD3+ : Pmic - Supervisor Integrated Circuit (ics) Regulator/Supervisor Tube 1; IC REG LIN W/SPR VSR 20-TQFN Specifications: Output: Push-Pull, Totem Pole ; Reset: Active Low ; Package / Case: 20-WQFN Exposed Pad ; Packaging: Tube ; Number of Voltages Monitored: 1 ; Reset Timeout: 35 ms Minimum ; Type: Regulator/Supervisor ; Voltage - Threshold: 2.313V ; Operating Temperature: -40C ~ 125C ; Lead Free Sta

MAX6473TA21BD2-T : FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, DSO8 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed, Adjustable / Variable ; Package Type: Other, 3 X 3 MM, 0.80 MM HEIGHT, MO-229WEEC, TDFN-8 ; Life Cycle Stage: ACTIVE ; Output Voltage: 1.23 to 5 volts ; IOUT: 0.3000 amps

MAX14722ATP+ : Current & Power Monitors & Regulators 60V, 2A Power Limiter with Current Foldback (1.5x Initial Current Limit) Maxim Integrated MAX14721, MAX14722, and MAX14723 High-Accuracy Adjustable Power Limiters guard systems against overcurrent faults in addition to positive overvoltage and reverse-voltage faults. When used with an optional external p-channel MOSFET, these devices also protect downstream circuitry

MAX12931BWEVKIT# : Interface Development Tools 2-Channel, 5kVRMS Digital Isolator kit Maxim MAX12931 Two-Channel Digital Isolators transfer digital signals between circuits with different power domains while using as little as 0.65mW per channel at 1Mbps with 1.8V. The two channels of the MAX12931 transfer data in opposite directions, and this makes the MAX12931 ideal for isolatin

Same catergory

APT15GP60BDF1 : 600,  , 2.70, 30, TO-247 B ,. The POWER MOS 7 IGBT is a new generation of high voltage power IGBTs. Using Punch Through Technology this IGBT is ideal for many high frequency, high voltage switching applications and has been optimized for high frequency switchmode power supplies. Low Conduction Loss Low Gate Charge Ultrafast Tail Current shutoff Symbol VCES VGE VGEM I CM SSOA PD TJ,TSTG.

BCR39PN : Npn/pnp Silicon Digital Transistor Array. Marking on SOT-363 package (for example W1s) corresponds to pin 1 of device Position in tape: pin 1 opposite of feed hole side Symbol VCEO VCBO VEBO Vi(on) IC Ptot Tj Tstg Collector-emitter voltage Collector-base voltage Emitter-base voltage Input on Voltage DC collector current Total power dissipation, 115 C Junction temperature Storage temperature.

STPS60L45C : Power Schottky Diodes->45 and 60V Power Schottky D. Low Drop Power Schottky Rectifier.

PCM50US05 : Ac-dc Power Supplies. 4000 VAC Isloation Low Leakage Current Single, Dual and Triple Outputs Worldwide Medical Approvals CCC Approved (PCM80) Both Line and Neutral Fused Input Voltage Input Frequency Input Current 90-264 VAC 47-63 Hz 1.35 A max 1.30 A max 1.60 A max Inrush Current at 115 VAC at 230 VAC 25 C cold start Power Factor PCM50: 0.55 typical PCM80/120: 0.94 min Earth.

5476C SL005 : Multi-Paired Cable 24AWG 6PR SHIELD 100ft SPOOL GRAY. s: Manufacturer: Alpha Wire ; RoHS:  Details ; Number of Pairs: 6 ; Wire Size (AWG): 24 ; Stranding: 7 x 32 ; Shielding: Shielded ; Length: 100 ft ; Outside Diameter: 7.42 mm ; Jacket Material: Polyvinyl Chloride (PVC) ; Voltage Rating: 300 V ; Plenum (Y/N): No ; Type: Communication and Control.

ECG-C0KB150R : 15F Aluminum Capacitor Non-Standard SMD 8V; CAP ALUM 15UF 8V 20% SMD. s: Capacitance: 15F ; ESR (Equivalent Series Resistance): - ; : Polymer ; Lifetime @ Temp.: 1000 Hrs @ 105C ; Size / Dimension: 0.311" L x 0.209" W (7.90mm x 5.30mm) ; Lead Spacing: - ; Surface Mount Land Size: 0.311" L x 0.209" W (7.90mm x 5.30mm) ; Mounting Type: Surface Mount.

1-281838-0 : Free Hanging (In-Line) Rectangular - Housing Connectors, Interconnect Female Socket; HOUSING HE13 HE14 COSI 10 P. s: Color: Blue ; Contact Termination: IDC ; Contact Type: Female Socket ; Mounting Type: Free Hanging (In-Line) ; Number of Rows: 1 ; Pitch: 0.100" (2.54mm) ; Packaging: Bulk ; Connector Type: Receptacle ; Fastening Type: - ; : - ; Number.

MAX5961ETM+T : Pmic - Hot Swap Integrated Circuit (ics) Hot-Swap Controller Tape & Reel (TR) - 2.7 V ~ 16 V; IC CTRLR HOT-SWAP QD 48-TQFN. s: Applications: General Purpose, PCI Express ; Type: Hot-Swap Controller ; Package / Case: 48-WFQFN Exposed Pad ; Packaging: Tape & Reel (TR) ; Current Limit: - ; Internal Switch(s): No ; Operating Temperature: -40C.

MS3101E16-10P : Aluminum, Olive Drab Cadmium Plated Free Hanging (In-Line) Circular Connectors, Interconnect Receptacle, Male Pins; CONN RCPT 3 POS FREE HNG W/PINS. s: Connector Type: Receptacle, Male Pins ; Shell Size - Insert: 16-10 ; Mounting Type: Free Hanging (In-Line) ; Fastening Type: Threaded ; : Strain Relief ; Packaging: Bulk ; Number of Positions: 3 ; Termination:.

AT49BV162A-70CI : Memory Integrated Circuit (ics) FLASH Tray 2.65 V ~ 3.6 V; IC FLASH 16MBIT 70NS 48CBGA. s: Memory Type: FLASH ; Memory Size: 16M (2M x 8, 1M x 16) ; Speed: 70ns ; Interface: Parallel (Byte-wide) ; Package / Case: 48-CBGA ; Packaging: Tray ; Voltage - Supply: 2.65 V ~ 3.6 V ; Operating Temperature: -40C ~ 85C ; Format - Memory: FLASH ; Lead Free Status:.

R1966RUBBERSEAL : Accessory Switch; ROCKER SWITCH SEAL R1966. s: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.

71719-082 : Through Hole Modular - Jack Connectors, Interconnect Jack; 71719-82-A-TMT ASSEMBLY HDR 8. s: Connector Type: Jack ; : Board Lock ; LED Color: Does Not Contain LED ; Mounting Type: Through Hole ; Number of Ports: 1 ; Number of Positions/Contacts: 8p8c (RJ45, Ethernet) ; Number of Rows: 1 ; Ratings: - ; Shielding: - ; Tab Direction: Down ; Termination:.

LB5413-AW : T-1 3/4 SINGLE COLOR LED, BLUE, 5 mm. s: LED Type: Blue ; Peak Wavelength: 465 nm (4650 Å) ; Viewing Angle: 15 degrees ; Luminous Intensity: 1.46 milliCandela ; Forward Current: 20 milliamps ; LED Package : T-1 3/4.

EPLC2-HB-150LED-RT-480V : 347-480V Class 2 Division 1 Explosion Proof 150 Watt High Bay LED Light Fixture - 12,500 Lumens -. The Larson Electronics EPLC2-HB-150LED-RT-480V Explosion Proof High Bay light fixture provides operators with a powerful and energy efficient 347-480V LED alternative to traditional hazardous location luminaries. This Class 1 Division 2 and Class 2 Division.

0-C     D-L     M-R     S-Z