Details, datasheet, quote on part number: MCP6N11T-100E/MNY
PartMCP6N11T-100E/MNY
Category
TitleIC OPAMP INSTR 35MHZ RRO 8TDFN
Description

The Microchip MCP6N11 single instrumentation amplifier is optimized for single-supply operation with rail-to-rail input and output performance. Two external resistors set the gain, minimizing gain error and drift overtemperature. The supply voltage range of 1.8 V to 5.5 V is low enough to support many portable applications. The MCP6N16 is a zero-drift operational amplifier designed for single-supply operation with rail-to-rail input (no common mode crossover distortion) and output performance. The supply voltage range is low enough to support many portable applications. Each device has EMI filters at the input pins, providing superior EMI rejection. This family has three minimum gain options 1, 10, and 100 V/V to allow the user to optimize the input offset voltage and input noise for different applications. All devices are fully specified from -40°C to +125°C.



CompanyGenesis Microchip Inc.
DatasheetDownload MCP6N11T-100E/MNY datasheet
Quote
Find where to buy
 
  
MCP6N11T-100E/MNY photo

Others parts numbering
MCP6N11T-010E/MNY: IC OPAMP INSTR 5MHZ RRO 8TDFN
MCP6N11-100E/SN: IC OPAMP INSTR 35MHZ RRO 8SOIC
MCP6N16-100E/MS: IC OP AMP INSTR 8MSOP
MCP6N16-001E/MS
MCP6N16-100E/MF: IC OP AMP INSTR 8DFN
MCP6N16-010E/MS: IC OP AMP INSTR 8MSOP
MCP6N11T-001E/MNY: IC OPAMP INSTR 500KHZ RRO 8TDFN
MCP6N11-010E/SN: IC OPAMP INSTR 5MHZ RRO 8SOIC
MCP6N11-005E/SN: IC OPAMP INSTR 2.5MHZ RRO 8SOIC
MCP6N11-002E/SN: IC OPAMP INSTR 1MHZ RRO 8SOIC
MCP6N11-001E/SN: IC OPAMP INSTR 500KHZ RRO 8SOIC
ARD00354: BOARD REF DESIGN MCP6N11/MCP6V2X

 

Features, Applications
Features

Rail-to-Rail Input and Output Gain Set by 2 External Resistors Minimum Gain (GMIN) Options: or 100 V/V Common Mode Rejection Ratio (CMRR): 115 dB (typical, GMIN = 100) Power Supply Rejection Ratio (PSRR): 112 dB (typical, GMIN = 100) Bandwidth: 500 kHz (typical, Gain = GMIN) Supply Current: 800 A/channel (typical) Single Channel Enable/VOS Calibration pin: (EN/CAL) Power Supply: to 5.5V Extended Temperature Range: to +125C

Description

Microchip Technology Inc. offers the single MCP6N11 instrumentation amplifier (INA) with Enable/VOS Calibration pin (EN/CAL) and several minimum gain options. It is optimized for single-supply operation with rail-to-rail input (no common mode crossover distortion) and output performance. Two external resistors set the gain, minimizing gain error and drift-over temperature. The reference voltage (VREF) shifts the output voltage (VOUT). The supply voltage range 5.5V) is low enough to support many portable applications. All devices are fully specified from to +125C. These parts have five minimum gain options and 100 V/V). This allows the user to optimize the input offset voltage and input noise for different applications.

Typical Applications

High Side Current Sensor Wheatstone Bridge Sensors Difference Amplifier with Level Shifting Power Control Loops

Microchip Advanced Part Selector (MAPS) Demonstration Board Application Notes VFG

Table 1 shows key specifications that differentiate between the different minimum gain (GMIN) options. See Section 1.0 "Electrical Characteristics", Section 6.0 "Packaging Information" and Product Identification System for further information on GMIN.

VDD VSS.......................................................................6.5V Current at Input Pins ...............................................2 mA Analog Inputs (VIP and VIM) VSS 1.0V to VDD + 1.0V All Other Inputs and Outputs......... VSS 0.3V to VDD + 0.3V Difference Input Voltage....................................... |VDD VSS| Output Short Circuit Current................................ Continuous Current at Output and Supply Pins............................30 mA Storage to +150C Max. Junction Temperature........................................ +150C ESD protection on all pins (HBM, CDM, MM). 2 kV, 1.5 kV, 300V

Notice: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. See Section 4.2.1.2 "Input Voltage Limits" and Section 4.2.1.3 "Input Current Limits".

Specifications

Electrical Characteristics: Unless otherwise indicated, = +25C, VDD to 5.5V, VSS = GND, EN/CAL = VDD, VCM = VDD/2, VDM = 0V, VREF to VL and GDM = GMIN; see Figure 1-6 and Figure 1-7.

Parameters Input Offset Input Offset Voltage, Calibrated
Input Offset Voltage Drift Power Supply Rejection Ratio

VCM = (VIP + VIM) / 2, VDM = (VIP VIM) and GDM 1 + RF/RG. The VOS spec limits include 1/f noise effects. This is the input offset drift without VOS re-calibration; toggle EN/CAL to minimize this effect. These specs apply to both the VIP, VIM input pair (use VCM) and to the VREF, VFG input pair (VREF takes VCM's place). This spec applies to the VIP, VIM, VREF and VFG pins individually. Figure 2-11 and Figure 2-19 show the VIVR and VDMR variation over temperature. See Section 1.5 "Explanation of DC Error Specs".


 

Some Part number from the same manufacture Genesis Microchip Inc.
MCP6N11T-010E/MNY

The Microchip MCP6N11 single instrumentation amplifier is optimized for single-supply operation with rail-to-rail input and output performance. Two external resistors set the gain, minimizing gain error

MCP6N11-100E/SN
MCP6N16-100E/MS
MCP6N16-001E/MS
MCP6N16-100E/MF
MCP6N16-010E/MS
MCP6N11T-001E/MNY
MCP6N11-010E/SN
MCP6N11-005E/SN
MCP6N11-002E/SN
MCP6N11-001E/SN
ARD00354
 
0-C     D-L     M-R     S-Z