Details, datasheet, quote on part number: 8T49N240-991NLGI
Part8T49N240-991NLGI
Category
TitleULTRA-PERFORMANCE JITTER ATTENUA
Description

Integrated Device Technology features their highly programmable clock generator and jitter attenuator IC featuring less than 200 fs of phase noise, providing valuable system design margin for 10 Gbps interfaces in wireline and wireless communication networks. The additional phase noise margin eases system design constraints, allowing engineers to minimize bit error rates (BER) while lowering overall system costs.



CompanyIntegra Technologies
DatasheetDownload 8T49N240-991NLGI datasheet
  
8T49N240-991NLGI photo

 

Features, Applications

Description

The is a fractional-feedback single channel jitter attenuator with frequency translation. It is equipped with three integer and one fractional output dividers, allowing the generation up to four different output frequencies, ranging from to 867MHz. These frequencies are completely independent of the input reference frequencies and the crystal reference frequency. The outputs may select among LVPECL, LVDS, HCSL, or LVCMOS output levels. The 8T49N240 accepts up to two differential or single-ended input clocks and a fundamental-mode crystal input. The internal PLL can lock to either of the input reference clocks or just to the crystal to behave as a frequency synthesizer. The PLL can use the second input for redundant backup of the primary input reference, but in this case, both input clock references must be integer related in frequency. The device supports hitless reference switching between input clocks. The device monitors both input clocks for Loss of Signal (LOS), and generates an alarm when an input clock failure is detected. Automatic and manual hitless reference switching options are supported. LOS behavior can be set to support gapped or un-gapped clocks. The 8T49N240 supports holdover. The holdover has an initial accuracy of 50ppB from the point where the loss of all applicable input reference(s) has been detected. It maintains a historical average operating point for the PLL that may be returned to in holdover at a limited phase slope. The PLL has a register-selectable loop bandwidth from to 6.4kHz. The device supports Output Enable and Clock Select inputs and Lock, Holdover, and LOS status outputs. The device is programmable through an I2C interface. It also supports I2C master capability to allow the register configuration to be read from an external EEPROM. Factory pre-programmed devices are also available using the on-chip One Time Programmable (OTP) memory.

Features

Four differential outputs Excellent jitter performance: <200fs (typical) RMS (including spurs): to 20MHz for integer-divider outputs in jitter attenuator mode or in fractional-feedback synthesizer mode Operating Modes: Synthesizer, Jitter Attenuator Operates from to 54MHz fundamental-mode crystal Initial holdover accuracy of +50ppb Accepts up to two LVPECL, LVDS, LVHSTL, or LVCMOS input clocks Accepts frequencies ranging from to 875MHz Auto and manual clock selection with hitless switching Clock input monitoring including support for gapped clocks Phase-slope limiting and fully hitless switching options to control output clock phase transients Three outputs generate LVPECL / LVDS / HCSL clocks, one output generates LVPECL / LVDS / HCSL / LVCMOS clocks Output frequencies ranging from to 867MHz (differential) Output frequencies ranging from to 250MHz (LVCMOS) Three integer dividers with fixed divider ratios (see Table 3) One fractional output divider Programmable loop bandwidth settings from to 6.4kHz Optional fast-lock function Four General Purpose I/O pins with optional support for status and control: Two Output Enable control inputs provide control over the four clocks Manual clock selection control input Lock, Holdover, and Loss-of-Signal alarm outputs Open-drain Interrupt pin Register programmable through I2C or via external I2C EEPROM Full or 3.3V supply modes, with some support for to 85C ambient operating temperature Package: mm 40-VFQFN, lead-free (RoHS 6)

Typical Applications

OTN, including ITU-T G.709 (2009) FEC CPRI interfaces Fiber optics 40G/100G Ethernet Gb Ethernet, Terabit IP switches / routers

nRST VCCA OSCI OSCO S_A1 VCCCS CAP1 CAP2 CAP_REF VCCA
Name VCCA Q1 VCCO1 SDATA SCLK Power I/O Power O I/O O Power I/O

Description Analog function supply for core analog functions. or 3.3V supported. Analog function supply for analog functions associated with PLL. or 3.3V supported. Pullup General-purpose input-output. LVTTL / LVCMOS Input levels. High-speed output supply for output pair or 3.3V supported for differential output types. LVCMOS outputs also support 1.8V.

Output Clock 0. For more information, see Output Drivers. Output Clock 0. For more information, see Output Drivers. General-purpose input-output. LVTTL / LVCMOS Input levels. Output Clock 1. For more information, see Output Drivers. Output Clock 1. For more information, see Output Drivers. High-speed output supply for output pair or 3.3V supported for differential output types. LVCMOS outputs also support 1.8V.

I2C interface bi-directional data. I2C interface bi-directional clock.

 

Some Part number from the same manufacture Integra Technologies
74LVC1G3157 The 74LVC1G3157 single-pole, double-throw analog switch operates from a 1.65 to 5.5 V supply and can handle signal amplitudes between Vcc and ground. It includes ESD and latch-up protection, and the ICs low 6 Ω
2SD300C17A2

Power Integrations SCALE-2 IGBT (Insulated Gate Bipolar Transistor) Gate Driver Cores provide a highly flexible solution by including all commonly required driver functions in a single module. The SCALE-2

1SC0450V2A0-65
2SC0535T2A1-33
1SP0350V2A0ENG-45
2SP0115T2A0-12
2SC0650P2A0-17
2SP0115T2B0-12
1SC2060P2A0-17
2SC0108T2D0-12
2SC0108T2D0-07
1SP0635V2M1-17
2SC0650P2C0-17
1SP0635D2S1-FZ1200R33KF2C
2SP0320T2A0-12
2SP0115T2C0-12
1SP0335V2M1-45
1SP0635D2S1-12
1SP0635V2M1-12
2SP0115T2A0-17
2SP0115T2A0-2MBI225VN-120-50
 
0-C     D-L     M-R     S-Z