Details, datasheet, quote on part number: RI-02GP1520
PartRI-02GP1520
Category
TitleSWITCH REED SPST-NO 500MA 140V
Description

Comus RI series of glass reed switches are miniature dry contact magnetic switches that are hermetically sealed in a gas filled glass sleeve. A dry-reed switch can be defined as an assembly that contains two ferromagnetic NiFe contact blades hermetically sealed in a glass envelope and filled with an inert gas. The inert gas atmosphere protects the contact resistance of the reed switch, which is one of its most important electrical performance characteristics. The inert atmosphere is maintained by the integrity of the critical glass-to-metal seal of the switch. This seal is defined as a “residual stress seal,” which means that the seal is sensitive to handling.



CompanyInternational Semiconductor Technologies
DatasheetDownload RI-02GP1520 datasheet
  
RI-02GP1520 photo

Others parts numbering
RI-60GP1015
RI-60GP1520
RI-03GP1015: SWITCH REED SPST-NO 250MA 110V
RI-03GP1520
RI-03GP2025
RI-03GP2530
RI-27GP1015: SWITCH REED SPST-NO 500MA 130V
RI-27GP1520
RI-27GP2025
RI-23GP1520
RI-23GP2025
RI-23GP2530
RI-46GP1520: SWITCH REED SPST-NO 1A 200V
RI-46GP2025
RI-46GP2530: SWITCH REED SPST-NO 1A 250V
RI-46GP3035
RI-70GP0710: SWITCH REED SPST-NO 500MA 120V
RI-29GP1520: SWITCH REED SPST-NO 1A 140V
RI-29GP2025

 

Features, Applications

Ultra-miniature dry-reed switch hermetically sealed in a gas filled envelope. Single-pole, single-throw (SPST) type, having normally open contacts, and containing two magnetically actuated reeds. The switch is of the double-ended type and may be actuated by an electromagnet, a permanent magnet or combination of both. The device is intended for use in senors, relays, pulse counters or similar devices.

RI-02 Series Features Ideal for general purpose reed relays and sensors. Contact layers: ruthenium on gold Superior glass-to-metal seal and blade alignment RoHS Compliant Dimensions for RI-02 Series

All Dimension in inches (mm) nominal General data for all models RI-02

Besides the standard models, customized products can also be supplied offering the following options: Operate and release ranges to customer specification Cropped and/or performed leads

Loaded conditions (resistive load: V; 100 mA; operating frequency: 125 Hz)

All characteristics are measured using the Philips Standard Coil. For definitions of the Philips Standard Coil, refer to "Application Notes" in the Reed Switch Technical & Application Information Section of this catalog.

Life expectancy: min. x 106 operations with a failure rate of less than 10-8 with a confidence level of 90%. End of life critera: Contact resistance > 1 after 2.5 ms Release time 1 ms (latching or contact sticking).

Loaded conditions (resistive load: V; 500 mA; operating frequency: 125 Hz)

The life expectancy data given below are valid for a coil energized at 1.25 times the published maximum operate value for each type in the RI-02 series.

Life expectancy: min. 108 operations with a failure rate of less than x 10-10 with a confidence level of 90%. End of life criteria: Contact resistance > 1 after 2 ms

Life expectancy: min. x 106 operations with a failure rate of less than 10-7 with a confidence level of 90%. End of life critera: Contact resistance > 2 after 2.5 ms Release time 2.5 ms (latching or contact sticking). Switching different loads involves different life expectancy and reliability data. Further information is available on request.

Contact arrangement is normally open; lead finish is tinned; net mass is approximately 90mg; and can be

Operating Characteristics Operate Range Release Range Operate Time - including Bounce (typ.) Bounce Time (typ.) Release Time (max) Resonant Frequency (typ.) Electrical Characteristics Switched Power (max) Switched Voltage DC (max) Switched Voltage AC, RMS value (max) Switched Current DC (max) Switched Current AC, RMS value (max) Carry Current DC (max) Breakdown Voltage (min) Contact Resistance (initial max.) Contact Resistance (initial typ.) Contact Capacitance (max) Insulation Resistance (min) without test coil s Hz

The switches are tested in accordance with "IEC 68-2-27", test Ea (peak acceleration 100 G; half sinewave; duration 11ms). Such a shock will not cause an open switch (no magnetic field present) to close, nor a switch kept closed 80 AT coil to open.

The switch can withstand soldering heat in accordance with "IEC 68-2-20", test Tb, method 1B: solder bath 10C for 0.5 s. Solderability is tested in acc ordance with "IEC 68-2-20" test Ta, method 3: solder globule temperature 235C; ageing 1b: 4 hours steam.

The switches are tested in accordance with "IEC 68-2-26", test Fc (acceleration 10G; below cross-over-frequency to 62 Hz; amplitude 0.75 mm; frequency range to 2000 Hz; duration 90 minutes.) Such a vibration will not cause an open switch ( no magnetic field present) to close, nor a switch kept closed 80 AT coil to open.

The leads should not be bent closer than mm to the glass-to-metal seals. Stress on the seals should be avoided Care must be taken to prevent stray magnetic fields from influencing the operating and measuring conditions.

The robustness of the terminations is tested in accordance with "IEC 68-2-21", test Ua1 (load 10 N).

Operating ambient temperature; min: -55C; max: +125C. Storage temperature; min: -55; max: +125C. Note: Temperature excursions to 150C may be permissible. For more information contact your nearest Comus Group sales office.

As part of the company policy of continued product improvement, specifications may change without notice.Our sales office will be pleased to help you with the latest information on this product range and the details of our full design and manufacturing service. All products are supplied to our standard conditions of sale unless otherwise agreed in writing.

Comus International 454 Allwood Road Clifton, New Jersey 07012 U.S.A Tel: Fax: email: info@comus-intl.com Website: http://www.comus-intl.com

Comus Europe Ltd Unit 7, Rice Bridge Industrial Estate Thorpe Le - Soken Essex, England CO160HL Tel: (0)1255 862236 Fax: (0)1255 862014 email: sales@comuseurope.co.uk Website: http://www.comuseurope.co.uk

Comus Belgium BVBA Overhaamlaan 40 B-3700 Tongeren Belgium Tel: (0)12 390400 Fax: (0)12 235754 email: info@comus.be Website: http://www.comus.be

Comus Technology BV Jan Campertstraat 6416 SG Heerlen The Netherlands Tel: +31(0)45 5439345 Fax: +31(0)45 5427216 email: info@comus-intl.com Website: http://www.dry-reeds.com TAKE A LOOK AT OUR VARIETY OF PRODUCTS

Comus Electronics and Technologies India Private Limited 2nd Floor, No.31/33, Anjugam Nagar 2nd Street, Ashok Nagar, Jaferkhanpet Chennai 600083 Tamil Nadu, India Tel:+(91)-(44)-42023510 Fax:+(91)-(44)-22628198 email: info@comus-intl.com Website: http://www.comusindia.com


 

Some Part number from the same manufacture International Semiconductor Technologies
RI-60GP1015

Comus RI series of glass reed switches are miniature dry contact magnetic switches that are hermetically sealed in a gas filled glass sleeve. A dry-reed switch can be defined as an assembly that contains

RI-60GP1520
RI-03GP1015
RI-03GP1520
RI-03GP2025
RI-03GP2530
RI-27GP1015
RI-27GP1520
RI-27GP2025
RI-23GP1520
RI-23GP2025
RI-23GP2530
RI-46GP1520
RI-46GP2025
RI-46GP2530
RI-46GP3035
RI-70GP0710
RI-29GP1520
RI-29GP2025
 
0-C     D-L     M-R     S-Z