Details, datasheet, quote on part number: TUSB213RGYT
PartTUSB213RGYT
CategorySemiconductors => Interface => USB => USB Retimers, Redrivers and USB/MHL Switches
Part familyTUSB213 USB 2.0 High Speed Signal Conditioner
TitleUSB 2.0 HIGH SPEED SIGNAL CONDIT
DescriptionUSB 2.0 High Speed Signal Conditioner 14-VQFN 0 to 70
CompanyTexas Instruments Inc.
StatusACTIVE
ROHSY
SampleNo
DatasheetDownload TUSB213RGYT datasheet
Specifications 
ICC(Max)(uA)30mA
Package GroupVQFN
FeaturesSelectable DC Boost
RatingCatalog
ESD HBM(kV)0.5
ICC(Typ)(uA)30
Operating Temperature Range(C)-40 to 85,0 to 70
Configuration240
Bandwidth(MHz)240
ESD HBM(Typ)(kV)2
Approx. Price (US$)1.50 | 1ku
VCC(Max)(V)480
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
14RGYVQFNS-PQFP-N250SMALL T&RUSB213 3.53.5.9.5
Evaluation Kits
TUSB213EVM: USB 2.0 High Speed Signal Conditioner Evaulation Module

Others parts numbering
TUSB213RGYT
TUSB213RGYT
TUSB212IRWBT
TUSB212IRWBT
TUSB212IRWBT
TUSB213IRGYT
TUSB213IRGYT
TUSB213IRGYT
TUSB214RWBT
TUSB214RWBT
TUSB214RWBT
TUSB215RGYT
TUSB215RGYT
TUSB215RGYT
TUSB214IRWBT
TUSB214IRWBT
TUSB214IRWBT
TUSB215IRGYT
TUSB215IRGYT

 

Features, Applications

The is a USB High-Speed (HS) signal conditioner, designed to compensate for ISI signal loss in a transmission channel which helps passing USB electrical compliance tests. TUSB213 has a patent-pending design which is agnostic to USB Low Speed (LS) and Full Speed (FS) signals. LS and FS signal characteristics are unaffected by the TUSB213 while HS signals are compensated. Programmable signal AC boost and DC boost permits fine tuning device performance to optimize High Speed signals at the connector, this allows use in many different applications. In addition, TUSB213 is compatible with the USB OnThe-Go (OTG) and Battery Charging (BC) protocols. Device Information

Compatible with USB 2.0, OTG 2.0 and BC 1.2 Pin strap or I2C Configurable Support for LS, FS, HS signaling Ultra-low USB Disconnect and Shutdown Power Consumption Scalable solution - Daisy Chain Device for High Loss Applications D1P/M and D2P/M Interchangeable and Host/Device Agnostic Supports to 5m pre-channel or 2m postchannel Cable Length Four Selectable AC Boost Setting Via External Pulldown Resistor DC Boost Along With AC Boost for Best Signal Integrity

Notebooks Desktops Docking Stations Tablets Cell Phones Active Cable, Cable Extenders Backplane Televisions

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA.

Features.................................................................. Applications........................................................... Description............................................................. Revision History..................................................... Pin Configuration and Functions......................... Specifications.........................................................

Absolute Maximum Ratings...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information.................................................. Electrical Characteristics........................................... Switching Characteristics.......................................... Typical Characteristics..............................................

Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks........................................................... Electrostatic Discharge Caution............................ Glossary................................................................

Changes from Revision A (August 2017) to Revision B Page

Changed Note From: Pull-up resistors for SDA and SCL pins in I2C mode should k (5%). To: Pull-up resistors for SDA and SCL pins in I2C mode should (5%) in the Pin Functions table.......................................................... 3 Added Test Conditions to RSTN: VIH and VIL in the Electrical Characteristics table.............................................................. 5 Added new parameters to SCL/SDA: VIH, VIL, VSDA_OL, ISDA_OL the Electrical Characteristics table..................................... 5 Added Test Conditions To: DC_BOOST: VIH, VIM, and VIL the Electrical Characteristics table............................................. 5 Added test conditions to trise_dxx and tfall_dxx in the Switching Characteristics table................................................................. 6 Page

Changed CIO_DXX TYP value From: 7 pF To: pF in the Electrical Characteristics table................................................... 6

Submit Documentation Feedback Product Folder Links: TUSB213

PIN NAME NO. I/O INTERNAL PULLUP/PULLDOWN DESCRIPTION USB High Speed AC boost select via external pull down resistor. Sampled upon de-assertion of RSTN. Does not recognize real time adjustments. See application section for details. Auto selects maximum AC boost level when left floating. Leave unconnected. In I2C mode: Reserved for TI test purpose. In non-I2C mode: At reset: 3-level input signal DC_BOOST. USB High Speed DC signal boost selection. H (pin is pulled high) mV M (pin is left floating) mV L (pin is pulled low) 40 mV After reset: Output signal ENA_HS. Flag indicating that channel is in High Speed mode. Asserted upon: 1. Detection of USB-IF High Speed test fixture from an unconnected state followed by transmission of USB TEST_PACKET pattern. 2. Squelch detection following USB reset with a successful HS handshake [HS handshake is declared to be successful after single chirp J chirp K pair where each chirp is within 128 s]. N/A USB High Speed positive port. USB High Speed negative port. Ground 1.8-V LDO output. Only enabled when operating in High Speed mode. Requires 0.1-F external capacitor to GND to stabilize the core. USB High Speed negative port.. USB High Speed positive port. I2C Mode: Bidirectional I2C data pin [I2C address 0x2C]. In non I2C mode: Reserved for TI test purpose.

Pull-down and pull-up (to 3.3 V) resistors for DC_BOOST pins must be between k in non I2C mode. Pull-up resistors for SDA and SCL pins in I2C mode should (5%). If both SDA and SCL are pulled up at reset the device enters into I2C mode. Submit Documentation Feedback Product Folder Links: TUSB213 3


 

Some Part number from the same manufacture Texas Instruments Inc.
TUSB213RGYT

Texas Instruments' TUSB212, TUSB213, TUSB214, and TUSB215 are USB high-speed (HS) signal conditioners, designed to compensate for ISI signal loss in a transmission channel.



TUSB213RGYT
TUSB212IRWBT
TUSB212IRWBT
TUSB212IRWBT
TUSB213IRGYT
TUSB213IRGYT
TUSB213IRGYT
TUSB214RWBT
TUSB214RWBT
TUSB214RWBT
TUSB215RGYT
TUSB215RGYT
TUSB215RGYT
TUSB214IRWBT
TUSB214IRWBT
TUSB214IRWBT
TUSB215IRGYT
TUSB215IRGYT
 
0-C     D-L     M-R     S-Z