Details, datasheet, quote on part number: ICP-10100
PartICP-10100
Category
TitleHIGH ACCURACY, LOW POWER, WATERP
Description

TDK InvenSense's ICP-101xx barometric pressure sensor family is based on MEMS capacitive technology which provides ultra-low noise at the lowest power, enabling industry leading relative accuracy, sensor throughput, and temperature stability. The pressure sensor can measure pressure differences with an accuracy of ±1 Pa, an accuracy enabling altitude measurement differentials as small as 5 cm, less than the height of a single stair step. Consuming only 1.3 µA at 1 Hz, available in a small footprint 2 mm x 2 mm x 0.72 mm, waterproof to 1.5 m depth, 10-pin LGA package (ICP-10100), the ICP-101xx is ideally suited for mobile phones, wearable fitness monitoring, drones, and battery powered IoT devices. The ICP-101xx offers an industry leading temperature coefficient offset of ±0.5 Pa/°C. The combination of high accuracy, low power, temperature stability, and waterproofing in a small footprint enables higher performance barometric pressure sensing for sports activity identification, mobile indoor/outdoor navigation, and altitude-hold in drones.



CompanyInvensense
DatasheetDownload ICP-10100 datasheet
  
ICP-10100 photo

Others parts numbering
DK-10100: ICP-10100 DEVELOPMENT KIT BOARD

 

Features, Applications

ICP-10110, ICP-10111 High Accuracy, Low Power, Waterproof Barometric Pressure and Temperature Sensor IC

The ICP-101xx pressure sensor family is based on MEMS capacitive technology which provides ultra-low noise at the lowest power, enabling industry leading relative accuracy, sensor throughput, and temperature stability. The pressure sensor can measure pressure differences with an accuracy of 1 Pa, an accuracy enabling altitude measurement differentials as small as 8.5 cm, less than the height of a single stair step. Consuming only A @1 Hz, available in a small footprint 0.72 mm waterproof to 1.5m depth 10-pin LGA package (ICP-10100), the ICP-101xx is ideally suited for mobile phones, wearable fitness monitoring, drones, and battery powered IoT. The ICP-101xx offers an industry leading temperature coefficient offset of 0.5 Pa/C. The combination of high accuracy, low power, temperature stability, waterproofing in a small footprint enables higher performance barometric pressure sensing for sports activity identification, mobile indoor/outdoor navigation, and altitude-hold in drones.

FEATURES

Pressure operating range: to 110 kPa Noise and current consumption 10.4 A (ULN mode) 5.2 A (LN mode) 1.3 A (LP mode) Pressure Sensor Relative Accuracy: 1 Pa for any 10 hPa change over 950 hPa-1050 hPa at 25C Pressure Sensor Absolute Accuracy: 1 hPa over 950 hPa-1050 hPa, to 65C Pressure Sensor Temperature Coefficient Offset: 0.5 Pa/C over at 100 kPa Temperature Sensor Absolute Accuracy: 0.4C IPx8: Waterproof to 1.5m depth & ICP10110) Temperature operating range: 85 C Host Interface: to 400 kHz Single Supply voltage: 1.8V 5% RoHS and Green compliant

APPLICATIONS

Altitude Control of Drones and Flying Toys Mobile Phones Virtual Reality and Gaming Equipment Indoor/Outdoor Navigation (dead-reckoning, floor/elevator/step detection) Vertical velocity monitoring Leisure, Sports, and Fitness Activity Identification Weather Forecasting

This document contains information on a pre-production product. InvenSense Inc. reserves the right to change specifications and information herein without notice..

TDK Corporation 1745 Technology Drive, San Jose, CA 95110 U.S.A +1(408) 9887339 www.invensense.com

 

Some Part number from the same manufacture Invensense
DK-10100

TDK InvenSense's ICP-101xx barometric pressure sensor family is based on MEMS capacitive technology which provides ultra-low noise at the lowest power, enabling industry leading relative accuracy, sensor

 
0-C     D-L     M-R     S-Z