|
Details, datasheet, quote on part number:06A84C32
| |
Datasheet text preview:
V23806-A84-C32
Single Mode 622 MBd ATM Transceiver 1x9
Dimensions in (mm) inches
(11.5 max) .453 max. (2) .080 (1.5±0.1) .06±.004
(4±0.2) .158±.008 a)
View Z (Lead cross section and standoff size) (0.73±0.1) .028±.004
(7.420.15) .292.006 Optical Centerline 6.375 (0.75±0.1) .251 .030±.004 (9.6+0.1) .378+.004 9x (0.8±0.1) .032±.004 11x 0.1 M .004 M
PC board 2x
PC board thickness 11x 0.25 typ. .020 typ. 0.25 typ. .010 typ. 9x 0.3 M A .012 M A (25.4±0.1) 1±.004 8x 2.54=20.32 8x .100=.800
Z
q q q q q q q q q
0.1 M .004 M
0.3 M A .012 M A
q q q
(1.6±0.1) .063±.004 (b) Rx DUPLEX SC RECEPTACLE Tx 12.7 .500
q q
8x 2.54=20.32 8x .100=.800 (20 1) .787 .040
q q
123456789
q q
(2.54) .100 (2.54) .100
20.32 .800
19±0.1 2x .075±.004
a. Different length of pins available. maximum: (7.5) .295 b. Isolated posts on request
20.32 .800 (38.62±0.1) 1.52±.004
(15.88±0.5) .625±.020
(12.6±0.3) .496±.012
Maximum Ratings (Absolute maximum stress) Exceeding any one of these values may destroy the device immediately. However, the electro-optical characteristics described in the following tables are only valid for use under the recommended operating conditions. Package Power Dissipation (1) ... 1.5 W Supply voltage (VCCVEE) ..... 6 V Data Input Levels(PECL) .... VCC0.7 V Differential Data Input Voltage........ 3 V Operating Case Temperature ........ 0 to 70°C Storage Ambient temperature ......40°C to 85°C Soldering Conditions Temp/Time (MIL-STD 883C, Method 2003).....250/5.5°C/s
Notes 1. For VCCVEE (min, max). 50% duty cycle. The supply current does not include the load drive current of the receiver output. Add max. 45 mA for the three outputs. Load is 50 to VCC2 V.
FEATURES · Compliant with existing standards · Compact integrated transceiver unit with MQW laser diode transmitter InGaAs PIN-photo diode receiver Duplex SC receptacle · Class 1 FDA (Accession No. 95 20 890 supplement 0.01) and IEC laser safety compliant · Single power supply (5 V) · Loss of optical signal indicator, TTL compatible · Class 1 FDA an IEC laser safety compliant · PECL differential inputs and outputs · Wave solderable and washable with included process plug
910
DESCRIPTION This data sheet describes the Siemens single mode ATM transceiver, which complies with the ATM Forum's Network Compatible ATM for Local Network Applications document and ANSI's Broadband ISDN--Customer Installation Interfaces, Physical Media Dependent Specification, T1.6461995. ATM is being developed to facilitate solutions in multimedia applications and real time transmission. The data rate is scalable, and the ATM protocol is the basis of the broadband public networks being standardized in the International Telecommunications Union (ITU), the former International Telegraph and Telephone Consultative Committee (CCITT). ATM can also be used in local private applications. The Siemens single mode ATM transceiver is a single unit comprised of a transmitter, a receiver, and an SC receptacle. It thereby frees the customer from many alignment and PC board layout concerns. The module is designed for low cost WAN applications. It can be used as the network end device interface in workstations, servers, and storage devices, and in a broad range of network devices such as bridges, routers, intelligent hubs, and wide area ATM switches. This transceiver operates at 622.080 Mbits per second from a single power supply (+5 Volt). The full differential data inputs and data and clock outputs are PECL compatible. Functional Description of 1x9 Pin Row Transceiver The transceiver is designed to transmit serial data via single mode cable. Figure 1. Functional diagram
The transmitter converts electrical ECL compatible serial data (TD and TDnot) into optical serial data. It contains a laser driver circuit which drives the modulation and bias current of the laser diode. The currents are controlled by a power control circuit to guarantee a constant output power of the laser over temperature and aging. The power control uses the output of the monitor pin diode (mechanically built in the laser coupling unit) for the controlling function to prevent the laser power from exceeding the operating limits. This module ensures single fault condition with an integrated automatic shutdown circuit, which disables the laser when it detects transmitter failures. A reset is only possible by turnng the power off, then on again. The transceiver contains a supervisory circuit to control the power supply. This circuit makes an internal reset signal whenever the sup ply voltage declines below the reset threshold. It keeps the reset sig nal active for at least 140 milliseconds after the voltage has risen above the reset threshold. During this time the laser is inactive. Recommended Operating Conditions
Parameter Case Temperature Power Supply Voltage Supply Current(1) Symbol Tc VCCVEE ICC Min. 0 4.75 5.0 150 Typ. Max. 70 5.25 250 Units °C V mA
Transmitter Data Input High Voltage Data Input Low Voltage Input Data Rise/Fall, 10-90% Receiver Output Current Io 1260 25 1360 mA nm VIHVCC VILVCC tR, tF 1165 1810 0.4 880 1475 1.3 ns mV
Input Center Wavelength C
Automatic Shut-Down
LEN TD TD Laser Coupling Unit e/o
Notes 1. For VCCVEE (min, max). 50% duty cycle. The supply current does not include the load drive current of the receiver output. Add max. 45 mA for the three outputs. Load is 50 to VCC2 V.
Laser Driver Power Control
Monitor
Laser
Transmitter Electro-Optical Characteristics
Transmitter Symbol Min. 15.0 1293 Typ. 11.0 Max. 8.0 1334 2.4 4.25 140 ER ED 8.2 4.38 240 4.5 560 V ms dB Units dBm nm Output Power (Average) Po
Single Mode Fiber
o/e
Center Wavelength Spectral Width (FWHM)
C Vth
RX Coupling Unit o/e
RD RD SD
Receiver
Reset Threshold for TXVCC(1) Reset Active Timeout(1) Extinction Ratio (dynamic)
The receiver component converts the optical serial data into ECL-compatible electrical data (RD and RDnot). The Signal Detect (SD, active high) shows whether a optical signal is present. If no optical input signal is present the receiver data outputs are switched to static low level (RD = Low, Rdnot = high).
Eye Diagram(2)
1. Power supply Tx is shut down and switched on above VTH after the reset active timeout. 2. Transmitter meets ANSI T1E1.2, SONET OC-12, and ITU G.957 mask pat terns.
911
V23806-A84-C32, Single Mode 622 MBd ATM Transceiver 1x9
Receiver Electro-Optical Characteristics
Receiver Sensitivity (Average Power)(1) Saturation (Average Power) Signal Detect Assert Level(2) Signal Detect Deassert Level(3) Signal Detect Hysteresis Signal Detect Assert Time(6) Signal Detect Deassert Time(7) Symbol PIN PSAT PSDA PSDD PSDA PSDD tASS tDAS 1950 1025 tbd 1.5 30 150 1630 mV 735 40ns V dB µs 8.0 Min. Typ. 33.0 Max. 29.0 Units dBm
PIN Description
Pin Name RxVEE RD Level/ Logic Pin# 1 2 3 4 Description Negative power supply, normally ground Receiver output data Inverted receiver output data A high level on this output shows an optical signal is applied to the optical input. Positive power supply, +5 V Inverted transmitter input data Transmitter input data Negative power supply, normally ground VEE/GND Support Stud (GND) connect to VEEnb
Rx Ground Power Supply Rx Output Data PECL Output
tbd
tbd
RDn Rx SD
RX Signal Detect
PECL Output active high Power Supply PECL Input
RVCC TVCC TDn TD TxVEE
Rx +5 V Tx +5 V Tx Input Data
5 6 7 8
Output LO Voltage(4) VOLVCC Output HI Voltage(4) Output SD, Rise/Fall Time(5) Output Data Rise/ Fall Time, 2080% VOH VCC tR, tF
Tx Ground Ground
Power Supply
9 S1/2
Notes 1. Minimum average optical power at which the BER is less than 1x10E-10. Measured with a 223-1 NRZ PRBS as recommended by ANSI T1E1.2, SONET OC-12, and ITU G.957. 2. An increase in optical power above the specified level will cause the SIGNAL DETECT output to switch from a LO state to a HI state. 3. A decrease in optical power below the specified level will cause the SIGNAL DETECT to change from a HI state to a LO state. 4. PECL 10K compatible. Load is 50 into VCC2V .Measured under DC conditions at 25°C. For dynamic measurements a tolerance of 50 mV should be added, VCC=5V. 5. PECL compatible. A high level on this output shows that an optical signal is applied to the optical input. 6. Measured by switching the light from <40 dBm to 25 dBm. 7. Measured by switching the light from 25 dBm to <40 dBm. Switching from higher power levels increases this time.
module must provide power supply protection that guarantees that the system power source will cease to provide power if the maximum recommended operation limit or more is detected on the +5 V at the power source. The temperature of the module case must be in the temperature range given in the recommended operating limits. These limits guarantee the laser safety. Usage Restrictions The optical ports of the modules must be terminated with an optical connector or with a dust plug.
Note Failure to adhere to the above restrictions could result in a modification that is considered an act of "manufacturing", and will require, under law, recertification of the modified product with the U.S. Food and Drug Administration (ref. 21 CFR 1040.10 (i)).
Figure 2. Required labels
Class 1 Laser Product (IEC) Laser Emission
LASER SAFETY This single mode ATM transceiver is a Class 1 laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated under the recommended operating conditions. Caution The use of optical instruments with this product will increase eye hazard! General Restrictions Classification is only valid if the module is operated within the specified temperature and voltage limits. The system using the
Complies with 21 CFR 1040.10 and 1040.11
(FDA)
Additional Information Laser Data
Wavelength Total output power (as defined by IEC: 50 mm aperture at 10 cm distance) Total output power (as defined by FDA: 7 mm aperture at 20 cm distance) Beam divergence 1300 nm 1 mW 180 µW 4°
912
V23806-A84-C32, Single Mode 622 MBd ATM Transceiver 1x9
APPLICATION NOTE FOR 1X9 PIN ROW TRANSCEIVER Figure 3. Schematic
VCCTX VCCRX 9 82R 82R 1 82R VCC L1 VCCRX
R1
R3
R5
82R
C1/3=4700 nF (optional) C2/4=4700 nF L1/2=1500 nH (L2 optional)* R1/3/5/7=82 Ohm R2/4/6/8=130 Ohm R9=200 Ohm
VCC
C1 C2 VCCTX
GND
GND
R7
TXD TXDN
130R 130R VCC-TX 200R 130R 130R
RD RDN SD
R2 R4
VCC-RX GND GNDGND GND
GND L2
GND
C3
C4
R9
R8
GND GND
R6 GND GNDGND
Transceiver
* Recommended choke is Siemens Matsushita B78108-S1153-K or B78148-S1153-K (Qmin=60, max. DC resistance =0.6 Ohm).
sensitivity performance. Studs must be connected to this GND plane. The transceiver contains an automatic shutdown circuit. Reset is only possible when the power off is switched off, then on again. (VCCTX=0V).
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module VCC-RX/VCC-TX. A GND plane under the module is required for good EMI and SONET/ATM APPLICATIONS FOR 1X9 PIN ROW TRANCEIVERS Description
The 1x9 Pin Row transceiver requires an external clock recovery device. The best solution is the use of transceiver circuits (serializer / deserializer) which include the clock recovery function. This avoids any additional circuitry skew problems between data and clock and a radiating 622 MHz signal path on the board. Reference Clock
51.84MHz
REFCKINP/N
Siemens
SM-ATM 622 TRX SERDATOP/N LPDATOP/N LPDATIP/N SERIDATIP/N LOS
SM-ATM 622 TRANSCEIVER
AMCC S3017
PIN[7:0]
TOUT[7:0]
PCLK PICLK
TCLK
PMC-Sierra PM 5355 S/UNI-622
s
V23806-A84-C2
YYWW nnnn
month year
REFCKINP/N
AMCC S3018
POUT[7:0] FP POCLK
PIN[0:7] RIFP RICLK
913
V23806-A84-C32, Single Mode 622 MBd ATM Transceiver 1x9
RxTx Chipsets including PLL Function
AMCC Sony: Texas Instruments Receiver S3017, Transmitter S3018 Transceivers CXB 1590 Q Transceivers TNETA 16611 (Preliminary, detailed description available) (Preliminary, detailed description available) (Preliminary)
Detailed information is available upon request.
ATM APPLICATIONS FOR 1X9 PIN ROW TRANCEIVERS Description The 1x9 Pin Row transceiver requires an external clock recovery device. The best solution is the use of transceiver circuits (serializer / deserializer) which include the clock recovery function. This avoids any additional circuitry skew problems between data and clock and a radiating 622 MHz signal path on the board. Reference Clock
51.84MHz
Siemens
SM-ATM 622 TRX
RFCKI
TCLK POUT (7 to 0)
TPCLK TPD (7 to 0)
SONY CXB 1590Q
TSD P/N PSD P/N LOST
PICLK PIN (7 to 0) FPIN OOF
RPCLK RPD (0 to 7) FP OOF
PMC-Sierra PM 5355 S/UNI-622
SM-ATM 622 TRANSCEIVER
s
V23806-A84-C2
YYWW nnnn
RxTx Chipsets including PLL Function
AMCC Sony: Texas Instruments Receiver S3017, Transmitter S3018 Transceivers CXB 1590 Q Transceivers TNETA 16611 Preliminary, detailed description available Preliminary, detailed description available Preliminary
Detailed Information is available upon request.
month year
914
V23806-A84-C32, Single Mode 622 MBd ATM Transceiver 1x9
|
|
