|
Details, datasheet, quote on part number:D2F-01
| |
Datasheet text preview:
Back
Subminiature Basic Switch
A Variety of D2F-series Models Including Models Incorporating Simulated Hinge Lever and Hinge Roller Lever
Subminiature switch (12.8 x 6.5 x 5.8 (W x H x D)) ideal for PCB mounting. Incorporating a reverse mechanism made with two highly precise split springs which ensures a long service life (1,000,000 operations). Two-stage bottom different in level and insertion terminals prevents flux penetration. PCB, self-standing, solder, and right angle terminals are available. Ideal for home electronics equipment, audio equipment, office machines, and communications equipment.
D2F
RC
Ordering Information
Actuator Terminals Microvoltage/current load 0.1 A Low operating force (75 gf) Pin p u ge plunger PCB terminals Self-clinching terminals Solder terminals Right angle terminals Hinge lever ee PCB terminals Self-clinching terminals Solder terminals Right angle terminals Simulated hinge lever ge e e PCB terminals Self-clinching terminals Solder terminals Right angle terminals Hinge roller lever oe ee PCB terminals Self-clinching terminals Solder terminals Right angle terminals D2F-01F D2F-01F-T D2F-01F-D D2F-01F-A D2F-01FL D2F-01FL-T D2F-01FL-D D2F-01FL-A D2F-01FL3 D2F-01FL3-T D2F-01FL3-D D2F-01FL3-A D2F-01FL2 D2F-01FL2-T D2F-01FL2-D D2F-01FL2-A General-purpose (150 gf) D2F-01 D2F-01-T D2F-01-D D2F-01-A D2F-01L D2F-01L-T D2F-01L-D D2F-01L-A D2F-01L3 D2F-01L3-T D2F-01L3-D D2F-01L3-A D2F-01L2 D2F-01L2-T D2F-01L2-D D2F-01L2-A 1A Low operating force (75 gf) D2F-F D2F-F-T D2F-F-D D2F-F-A D2F-FL D2F-FL-T D2F-FL-D D2F-FL-A D2F-FL3 D2F-FL3-T D2F-FL3-D D2F-FL3-A D2F-FL2 D2F-FL2-T D2F-FL2-D D2F-FL2-A Standard 3A General-purpose (150 gf) D2F D2F-T D2F-D D2F-A D2F-L D2F-L-T D2F-L-D D2F-L-A D2F-L3 D2F-L3-T D2F-L3-D D2F-L3-A D2F-L2 D2F-L2-T D2F-L2-D D2F-L2-A
115
D2F
D2F
Specifications
Ratings
OF max. 150 g Item Rated voltage Note: 125 VAC 30 VDC 3A 2A 1A 0.5 A Standard 75 g Resistive load --0.1 A Microvoltage/current load 150 g 75 g
Consult your OMRON representative before using the switch with inductive or motor loads.
Approved Standards
UL (File No. E32667)/CSA (LR21642) D2F-01 series: 0.1 A at 30 VDC D2F-F series: 1 A at 125 VAC, 0.5 A at 30 VDC (100,000 cycles) D2F-j series: 3 A at 125 VAC, 2 A at 30 VDC
Contact Form
COM
NO
NC
Characteristics
Operating speed Operating frequency (at pin plunger) Insulation resistance Contact resistance Dielectric strength 1 to 500 mm/s (at pin plunger) Mechanical: 200 operations/min Electrical: 30 operations/min 100 M min. (at 500 VDC) Standard: 30 m max. (initial value) Microvoltage/current load: 100 m max. (initial value) 600 VAC, 50/60 Hz for 1 min between contacts of the same polarity 1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal part Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Malfunction: 300 m/s2 (approx. 30G) Mechanical: 1,000,000 operations min. (OT value) Electrical: 30,000 operations min. Operating: 25°C to 85/° (with no icing) Operating: 85% max. Approx. 0.5 g
Vibration resistance Shock resistance Life expectancy Ambient temperature Ambient humidity Weight (at pin plunger)
116
D2F Operating Characteristics
Model OF max. RF min. PT max. OT min. MD max. FP max. OP Model OF max. RF min. OT min. MD max. FP max. OP D2Fj, D2F-01j 1.47 N (150 gf) 0.20 N (20 gf) 0.5 mm 0.25 mm 0.12 mm --5.5±0.3 mm D2F-L3j, D2F-01L3j 0.78 N (80 gf) 0.05 N (5 gf) 0.5 mm 0.45 mm 13 mm 8.5±1.2 mm D2F-FL3j, D2F-01FL3j 0.39 N (40 gf) 0.02 N (2 gf) 0.5 mm 0.45 mm D2F-Fj, D2F-01Fj 0.74 N (75 gf) 0.05 N (5 gf) 0.5 mm 0.25 mm 0.12 mm --D2F-Lj, D2F-01Lj 0.78 N (80 gf) 0.05 N (5 gf) --0.55 mm 0.5 mm 10 mm 6.8±1.5 mm D2F-L2j, D2F-01L2j 0.78 N (80 gf) 0.05 N (5 gf) 0.55 mm 0.5 mm 16.5 mm 13±2 mm
D2F
D2F-FLj, D2F-01FLj 0.25 N (25 gf) 0.02 N (2 gf) --0.55 mm 0.5 mm
D2F-FL2j, D2F-01FL2j 0.39 N (40 gf) 0.02 N (2 gf) 0.55 mm 0.5 mm
Engineering Data
Mechanical Life Expectancy
10,000 7,000 Without load Operating frequency: 60 operations/min
Electrical Life Expectancy
300 Operating frequency: 30/min Ambient temperature: 25°±3°C Ambient humidity: 70% max. 100 125 VAC 50 30 20 10 30 VDC
Number of operations (x10 3)
5,000 3,000
1,000 700 500 300 100
0
OT (mm)
Number of operations (x10 3)
Switching current (A)
117
D2F
D2F
Dimensions
Note: 1. All units are in millimeters unless otherwise indicated. 2. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. 3. The following illustrations and drawings are for D2F models with PCB terminals. Self-standing, solder, and right angle terminals are omitted from the following drawings. Refer to page 119 for these terminals. When ordering, replace j with the code for the terminal that you need.
Pin Plunger
D2Fj D2F-01j D2F-Fj D2F-01Fj
+0.12 2.2 0
12.7 1.2 dia. 5.2 PT +0.12 20 dia. holes
5.7 2.9
5
+0.12 20
OP 1.5 3.5
3.15
6.5±0.1 5.08 5.08 12.8±0.15
0.9
0.4 5.8±0.15
Hinge Lever
D2F-Lj D2F-01Lj D2F-FLj D2F-01FLj
12.8 (10.8) t = 0.3 (see note) 3
FP OP
Note:
Stainless steel lever
Simulate Hinge Lever
D2F-L3j D2F-01L3j D2F-FL3j D2F-01FL3j
12.7 (7.5) 10 1.3R FP 2.1 t = 0.3 (see note) 3
OP
Note:
Stainless steel lever
Hinge Roller Lever
D2F-L2j D2F-01L2j D2F-FL2j D2F-01FL2j
12.8 (10)
4 4.8 × 2.8 dia. (resin roller) (4.6)
t = 0.3 (see note)
4 OP FP
Note:
Stainless steel lever
118
D2F Terminals
PCB Terminals
D2F
D2F
Solder Terminals
D2F-D
1.5 3.5 3.15 6.5±0.1 5.08 5.08 12.8±0.15 0.9 0.4 5.8±0.15 Three, 0.8 dia. holes 3.15 6.5±0.1 5.08 5.08 12.8±0.15
1.5 2.4 1.6 0.4 5.8±0.15
Self-clinching Terminals
D2F-T
Right Angle Terminals
D2F-A
1.5 3.4 3.15 6.5±0.1 0.9 0.4 1.25±0.15 5.8±0.15 1.6±0.15 1.5 3.15 6.5±0.1 5.08 5.08 12.8±0.15
1.5 2.6 0.9 5.8±0.15 0.4
3.1
5.08 5.08 12.8±0.15
Precautions
Mounting
When mounting the switch to a PCB, refer to the following mounting dimensions. The gap between adjacent terminals is two pitches (2 x 2.54 cm). Mounting Dimensions
2.54 6.5 ± 0.15 5.8 ± 0.15 2.54
Use M2 mounting screws with plain or spring washers to mount the switch. Tighten the screws to a torque of 0.08 to 0.1 N S m (0.8 to 1 kgf S cm). Mounting Holes
Two , 2 dia. mounting holes
5.08 ± 0.1 12.8 ± 0.15
Three, 1.2 dia. holes
When soldering the relay terminals, use 6:4 solder and apply a soldering iron rated at 30 W and finish soldering within three seconds. After soldering, do not move the soldered terminals for at least one minute. Make sure that each adjacent terminals of the switch are properly insulated from each other and the terminals and ground is properly insulated.
Use of molded fittings is recommended to secure the switch. Mounting with Molded Pin
Two dia. molded pins
Switch
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. B36-E1-6
119
|
|
