|
Details, datasheet, quote on part number:QFH14
| |
Datasheet text preview:
Electronic control gear QUICKTRONIC® DIMMABLE for FH-lamps, single-lamp version QT-FH 1x14/230-240 DIM
Page 1
h
N L + -
1 2 3 4
b
a l
b
Reference : Mains voltage [V] : Permissible battery voltage [V] : Mains frequency [Hz] : Mains current [A] : System wattage [W] : Temperature range [°C] : Harmonics : Length l [mm] : Height h [mm] : Standard pack [pcs] :
h
L
QT-FH 1x14/230-240 DIM 230/240 176 - 254 0/50 - 60 0,09 18 +5 - +50 to DIN VDE 0712 Part 23/IEC 929/IEC 555-2/EN 60929 359 30 12
for lamp : Permissible voltage fluctuations [V] : Lamp start : Operating frequency [kHz] : Power factor [c] : Luminous flux [lm] : Radio interference suppression : Immunity : Width b [mm] : Distance between holes a [mm] : Weight [g] :
1x FH 14 W 198 - 264 Warm start within 2 s approx. 40 at 100% luminous flux, approx. 100 at 3% luminous flux 0,95 1350 to DIN VDE 0875/CISPR 15/EN 55015 to EN 61547 30 350 310
QUICKTRONIC® DIMMABLE for FH®/FQ® lamps This electronic high-frequency control gear enables FH® and FQ® lamps to be dimmed from 100% to 3% (1%) luminous flux via a 1 - 10V DC control line. The 1-10 V control line allows a wide variety of possible connections, ranging from simple manual control units for small systems through daylight-controlled regulation systems to modern energy management systems with PC and digital I-Bus technology. QUICKTRONIC® DIMMABLE goes beyond all current conventional and electronic solutions not just in terms of lighting comfort and energy consumption, but also in simplicity of operation and installation. Comfort: - Dimmable from 100% to 3% luminous flux for FH® lamps - Dimmable from 100% to 1% luminous flux for FQ® lamps - Flicker-free starting at all dimmer settings - Numerous control options with a low-voltage control signal (1 - 10 V) - Electronic control gear from different circuits can be dimmed together on different phases
Electronic control gear QUICKTRONIC® DIMMABLE for FH-lamps, single-lamp version QT-FH 1x14/230-240 DIM
Page 2 - Easy to incorporate into existing lighting control systems Economy: - Potentially large energy savings thanks to daylight-dependent lighting control - Long lamp life - Protective warm start Safety: - Safety shutdown of the power supply to defective lamps - Compliance with European standards for safety, operation and EMC - Overvoltage protective cutout for short-duration voltage surges (DIN VDE 0160) and for temporary overvoltages - Greater fire protection because lamps operate at lower temperatures and luminaires can be constructed to meet EN 60598/DIN VDE 0710 and DIN VDE 0711 standards - Can be used in emergency lighting systems as per DIN VDE 0108. Applications: Adjustable lighting in conference rooms, film projection rooms, exhibition rooms, CAD and PC rooms, control rooms, film recording studios, and for energy savings in offices with daylight-dependent lighting control. General: - Supply voltage: 230V/240V - Mains frequency: 0/50 to 60 Hz - Lamp start: warm start within 2 s. Lamp will start at any dimmer setting. - Radio interference suppression: to DIN VDE 0875/CISPR 15/EN 55015 - Mains harmonics: to DIN VDE 0712 Part 23/IEC 929/EN 61000-3-2/EN 60929 - Immunity to EN 61547 - Same luminous flux for AC and DC operation. - Values for luminous flux, mains current and system wattage at a dimmer setting of 100% - Max. 0.6 mA control current at the 1-10V interface
|
|
