Details, datasheet, quote on part number: STK7565A
PartSTK7565A
Category
Description
CompanyN.A.
DatasheetDownload STK7565A datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Applications

Voltage regulator for printers, electronic typewriters, XY plotters. Voltage regulator for MSX personal computers, floppy disk drive, computer terminals, portable VTRs.

Features

ICs having 2 outputs for microcomputer power supply (5V) and motor drive power supply 24, 36V) and being capable of delivering 2 regulated outputs from 1 rectifier. Good efficiency due to chopper type and no beat trouble due to fixed oscillation type oscillator common to 2 outputs. Independent overcurrent protectors for 2 outputs (Foldback characteristics). Output 2 (drive power supply) can be turned ON/OFF by external signal. Two outputs can be also turned ON/OFF simultaneously by an external circuit connected (Refer to Sample Application Circuit). High-precision setting of output voltage, elminating the need to use a variable resistor for adjustment. Input/output Gnd lines are united into one, facilatating combination with other nagative power supply. A negative voltage regulator (5V, 12V, etc.) can be connected externally (Refer to Sample Application Circuit). Output voltage/output current are provided in series.

Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein.

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN

Type No. STK7561J STK7561L Case Outline No.4050 No.4051 Type No. STK7562J STK7562L Case Outline No.4050 No.4051 Type No. STK7563J STK7563L Case Outline No.4050 No.4051 Type No. *STK7565A *STK7565F Case Outline No.4049 No.4050

Specifications

(Note) 1 Output 2 cutoff (pin 1 input ) : OUTPUT 2 cutoff 1V or less, OUTPUT 3V or greater. 2 The peak current value of OUTPUT (5V) is set 120% of the rating. 3 The peak current value of OUTPUT 36V) is set 200% of the rating considering the motor driving mode. 4 The secondary winding provided in the 5V choke coil makes OUTPUT 15V, 0.3A) available. 5 Peak current setting time.

Sample Application Circuit 1 : Standard peripheral circuit

Note 1 The N. C pin (pin 18) must not be used as a relay pin for other line, pin. 2 Pins connected inside the IC must be also connected on the printed circuit board.


 

Related products with the same datasheet
STK7560A
STK7560F
STK7560G
STK7560J
STK7561L
STK7562A
STK7562F
STK7562G
STK7562L
STK7563J
STK7563L
Some Part number from the same manufacture
STK7565F
STL39002
STL51004
STL51007
STL51704
STL81004
STL81007
STLC
STLC3040
STLC3040-TR
STLC5412
STLC5432
STLC5460
STLC5464
STLC7545
STLC7546
STLC7549
STM1645
STM326-2
STM51004
STM51007
 
0-C     D-L     M-R     S-Z