Details, datasheet, quote on part number: ACT8502
PartACT8502
CategoryAnalog & Mixed-Signal Processing => Switches & Multiplexers => Analog Multiplexers/Demultiplexers => Multiplexers
TitleMultiplexers
DescriptionAct8502 Radiation Hardened & Esd Protected 48-channel Analog Multiplexer Module
CompanyAeroflex Circuit Technology
DatasheetDownload ACT8502 datasheet
Quote
Find where to buy
 
  

 

Features, Applications
ACT8502 Radiation Hardened & ESD Protected 48-Channel Analog Multiplexer Module
Features

Full Military Temperature Range Low Power Consumption 90mW 48 Channels Provided by Six (6) HS-1840RH Multiplexers One Address Bus (A0-3) and Three Enable Lines All Channel Inputs protected by 20V Transorbs Fast Access Time 1500ns 35V Input Over Voltage Protection (Power On or Off) Break-Before-Make Switching High Analog Input Impedance (Power On or Off) Dielectrically Isolated Device Islands No Latch-Up Packaging Hermetic Ceramic Quad Flat Pack

96 Leads, 1.32"Sq x.20"Ht Quad Flat Pack Typical Weight 15 grams

Aeroflex's is a radiation hardened, multi-chip 48 channel multiplexer MCM (multi-chip module) with ESD protection for use in space applications. All channel inputs have electrostatic discharge protection. The ACT8502 has been specifically designed to meet exposure to radiation environments. The multiplexer is available a 96 lead High Temperature Co-Fired Ceramic (HTCC) Quad Flatpack (QFP) and is guaranteed operational from to +125C. Available screened in accordance with MIL-PRF-38534, the ACT8502 is ideal for demanding military and space applications.

eroflex Circuit Technology Multiplexer Modules For The Future SCD8502 REV A 10/26/01

The ACT8502 consists of six 16 channel muxes arranged as shown in the Block Diagram. The ACT8502 design is inherently Radiation Hard due to the HS1840RH Multiplexers as well as Microsemi Corp. Transient Suppressors (Reference Microsemi MicroNotes Series 050 page 14). 48 channels addressable by Bus A0~A3, in Three 16 channel blocks, each block enabled separately. Each block connects the addressed channel to two outputs, "Output" and "Current". This technique enables selecting and reading a remote resistive sensor without the MUX resistance being part of the measurement. For grounded sensors, this is done by passing current to the sensor by means of the "Current" pin and reading the resultant voltage (proportional to the sensor resistance) at the "Output" pin. NOTE: It is recommended that all "NC or "no connect pin", be grounded. This eliminates or minimizes any ESD or static buildup.


 

Related products with the same datasheet
ACT8502-7
ACT8502-C
ACT8502-I
ACT8502-S
ACT8502-T
Some Part number from the same manufacture Aeroflex Circuit Technology
ACT8502-7 Act8502 Radiation Hardened & Esd Protected 48-channel Analog Multiplexer Module
ACT8503 Act8503 Radiation Hardened & Esd Protected 48-channel Analog Multiplexer Module
ACT8504 Act8504 Radiation Hardened & Esd Protected 64-channel Analog Multiplexer Module With Mux Output Monitor Function
ACT8505 Act8505 Radiation Hardened 64-channel Analog Multiplexer Module With Mux Output Monitor Function
ACT8600 Act8600 - Rad Hard Dual Adjustable Positive & Negative Voltage Regulator
ACT8601 Radiation Hardened 50 Watt Power Supply Module
ACT8602
ACT8603
ACT8604
ACT8605
ACT8611
ACT8612
ACT8613
ACT8614
ACT8615
ACT861X
ACTE128K32 Act-e128k32 High Speed 4 Megabit EePROM Multichip Module
ACTF128K32 Act-f128k32 High Speed 4 Megabit Flash Multichip Module
ACTF128K8 Act-f128k8 High Speed 1 Megabit Monolithic Flash
ACTF1M32 Act-f1m32 High Speed 32 Megabit Boot Block Flash Multichip Module
ACTF2M32A Act-f2m32a High Speed 64 Megabit Sector Erase Flash Multichip Module
Same catergory

ADG708 : CMOS, Low Voltage, Single 8 to 1 Multiplexer. 5.5 V Single Supply 3 V Dual Supply 3 On-Resistance 0.75 On-Resistance Flatness 100 pA Leakage Currents 14 ns Switching Times Single 8-to-1 Multiplexer ADG708 Differential 4-to-1 Multiplexer ADG709 16-Lead TSSOP Package Low Power Consumption TTL/CMOS-Compatible Inputs APPLICATIONS Data Acquisition Systems Communication Systems Relay Replacement Audio.

ADP3020 : Power. High Efficiency Notebook Computer Power Supply Controller. High-Efficiency Notebook Computer Power Supply Controller ADP3020 Wide Input Voltage Range: 25 V High Conversion Efficiency > 96% Integrated Current Sense--No External Resistor Required Low Shutdown Current: 7 A (Typical) Dual Synchronous Buck Controllers with Selectable PWM/Power-Saving Mode Operation Built-In Gate Drive Boost Circuit for Driving.

CHA2066 : 10-16ghz Low Noise Amplifier. The is a two-stage wide band monolithic low noise amplifier. The circuit is manufactured with a standard HEMT process : 0.25m gate length, via holes through the substrate, air bridges and electron beam gate lithography. It is supplied in chip form. Broad band performance 10-16GHz 2.0dB noise figure, 10-16GHz 16dB gain, 0.5dB gain flatness Low DC power.

IL2903 : Dual Comparator. The IL2903 consists of two independent precision voltage comparators with an offset voltage as low 2.0 mV max for two comparators which were designed specifically to operate from a single power supply over a wide range of voltages. Application areas include limit comparators, simple analog to digital converters; pulse, squarewave and time delay generators;.

LM211-LM311 : Voltage Comparators. MAXIMUM INPUT CURRENT : 150nA MAXIMUM OFFSET CURRENT : 20nA DIFFERENTIAL INPUT VOLTAGE RANGE : 30V POWER CONSUMPTION AT 15V SUPPLY VOLTAGE TO 15V OUTPUT CURRENT : 50mA The LM111, LM211 and LM311 are voltage comparators that have low input currents. They are also designed to operateover a wide range of supplyvoltages : from standard 15V operational.

LM6311 : Low Noise Voltage Feedback High Speed Operational Amplifiers (discontinued).

LT1229 : LT1229, Dual 100MHz Current Feedback Amplifiers. 100MHz Bandwidth 1000V/s Slew Rate Low Cost 30mA Output Drive Current 0.04% Differential Gain 0.1 Differential Phase High Input Impedance: 25M, 3pF Wide Supply Range: to 15V Low Supply Current: 6mA Per Amplifier Inputs Common Mode to Within 1.5V of Supplies Outputs Swing Within 0.8V of Supplies The LT1229/LT1230 dual and quad 100MHz current feedback.

LT1920 : Single. Single Resistor Gainprogrammable, Precisioninstrumentation Amplifier.

MXL1007 : Low-Noise, Precision op Amp.

TLC085A : . TLC085, TLC08xA FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY OPERATIONAL AMPLIFIERS Wide Bandwidth. 10 MHz High Output Drive IOH. mA at VDD V IOL. 0.5 V High Slew Rate SR+. 16 V/s SR. 19 V/s Wide Supply Range. 16 V Supply Current. 1.9 mA/Channel Ultralow Power Shutdown Mode IDD. 125 A/Channel Low Input Noise Voltage. 8.5 nVHz.

TLC2142MP : Excalibur Low-noise High-speed Precision Operational Amplifiers. TLE214xA, TLE214xY EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS Low Noise 10 Hz. 15 nV/Hz 1 kHz. 10.5 nV/Hz 10 000-pF Load Capability 20-mA Min Short-Circuit Output Current 27-V/s Min Slew Rate High Gain-Bandwidth Product. 5.9 MHz Low VIO. 500 V Max at 25C Single or Split Supply. 44 V Fast Settling Time to 0.01% Saturation Recovery.

TLE2144A : . TLE214xA, TLE214xY EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS Low Noise 10 Hz. 15 nV/Hz 1 kHz. 10.5 nV/Hz 10 000-pF Load Capability 20-mA Min Short-Circuit Output Current 27-V/s Min Slew Rate High Gain-Bandwidth Product. 5.9 MHz Low VIO. 500 V Max at 25C Single or Split Supply. 44 V Fast Settling Time to 0.01% Saturation Recovery.

ADA4853-2 : ADA4853-2 - Dual, Low Power, Rail-to-Rail Output, Video Op Amp with Ultralow Power Disable Product The ADA4853-2 is a dual, low power, low cost, high speed, rail-to-rail output op amp with ultralow power disable that is ideal for portable consumer electronics. Despite its low price, the ADA4853-2 provides excellent overall performance and versatility.

AD8667 : 16V, 250 A Low Power, Low Noise Dual Precision CMOS Rail-to-Rail Output Operational Amplifier The AD8667 is a dual rail-to-rail output single supply and dual supply amplifiers that use Analog Devices patented DigiTrim trimming technique to achieve low offset voltage, 300μV over the common mode range. The AD8667 family an extended operating range.

NUF6410 : 6 Channel Low CAP Filter This device is a 6 line EMI filter array for wireless applications. Greater than -20 dB attenuation is obtained at frequencies from 800 MHz to 3.0 GHz. The NUF6410MN has a cut-off frequency of 250 MHz. This DFN package is specifically designed to enhance EMI filtering for low-profile or slim design electronics especially where.

 
0-C     D-L     M-R     S-Z