|
Details, datasheet, quote on part number:HLMP-Q150-F002S
| |
Datasheet text preview:
Subminiature LED Lamps Technical Data
HLMP-Pxxx Series HLMP-Qxxx Series HLMP-6xxx Series HLMP-70xx Series
Features
· Subminiature Flat Top Package Ideal for Backlighting and Light Piping Applications · Subminiature Dome Package Diffused Dome for Wide Viewing Angle Nondiffused Dome for High Brightness · TTL and LSTTL Compatible 5 Volt Resistor Lamps · Available in Six Colors · Ideal for Space Limited Applications · Axial Leads · Available with Lead Configurations for Surface Mount and Through Hole PC Board Mounting
Dome Packages The HLMP-6xxx Series dome lamps for use as indicators use a tinted, diffused lens to provide a wide viewing angle with a high on-off contrast ratio. High brightness lamps use an untinted, nondiffused lens to provide a high luminous intensity within a narrow radiation pattern. Resistor Lamps The HLMP-6xxx Series 5 volt subminiature lamps with built in current limiting resistors are for use in applications where space is at a premium. Lead Configurations All of these devices are made by encapsulating LED chips on axial lead frames to form molded epoxy subminiature lamp packages. A variety of package configuration options is available. These
Description
Flat Top Package The HLMP-Pxxx Series flat top lamps use an untinted, nondiffused, truncated lens to provide a wide radiation pattern that is necessary for use in backlighting applications. The flat top lamps are also ideal for use as emitters in light pipe applications.
include special surface mount lead configurations, gull wing, yoke lead or Z-bend. Right angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm (0.200 inch) center spacing are available for through hole mounting. For more information refer to Standard SMT and Through Hole Lead Bend Options for Subminiature LED Lamps data sheet.
2
Device Selection Guide Part Number: HLMP-xxxx
DH AS High High Standard AlGaAs Efficiency Perf. Emerald Red Red Red Orange Yellow Green Green P005 P105 P102 6000 Q100 Q105 Q150 Q155 6600 6620 6700 6720 6800 6820 P205 P202 6300 6305 7000 P405 P402 Q400 Q405 P305 P302 6400 6405 7019 P505 P502 6500 6505 7040 Q600 Q605 P605 Device Outline Drawing A A B B B B B B
Device Description [1] Untinted, Nondiffused, Flat Top Untinted, Diffused, Flat Top Tinted, Diffused Untinted, Nondiffused, High Brightness Tinted, Diffused, Low Current Nondiffused, Low Current Tinted, Diffused, Resistor, 5 V, 10 mA Diffused, Resistor, 5 V, 4 mA
Ordering Information
HLMX-XXXX-X X X X X Packaging Option Color Bin Selection Max. Iv Bin
Min. Iv Bin 4 x 4 Prod. Part Number
3
Package Dimensions
(A) Flat Top Lamps (B) Diffused and Nondiffused
0.50 (0.020) REF. 1.40 (0.055) .65 0.065) 11.68 (0.460) 0.67 0.420) BOTH SIDES CATHODE
0.50 (0.020) REF. 11.68 (0.460) 0.67 0.420) BOTH SIDES CATHODE
ANODE 1.65 (0.065) DIA. .91 0.075) 0.20 (0.008) MAX.
0.46 (0.018) .56 0.022) 0.25 (0.010) MAX. NOTE 2
ANODE 1.65 (0.065) DIA. .91 0.075) 0.20 (0.008) MAX.
0.46 (0.018) .56 0.022) 0.25 (0.010) MAX. NOTE 2
1 2.21 (0.087) .96 0.077) 1.14 (0.045) .40 0.055)
0.18 (0.007) .23 0.009) 0.63 (0.025) .38 0.015) 1 2.44 (0.096) .88 0.074) 2.03 (0.080) 1.78 (0.070)
1 2.21 (0.087) .96 0.077)
0.76 (0.030) R. .89 0.035) 1 0.94 (0.037) .24 0.049)
2.92 (0.115) MAX. 0.63 (0.025) .38 0.015) 2.08 (0.082) .34 0.092)
0.79 (0.031) MAX. 0.18 (0.007) .23 0.009) 2.08 (0.082) .34 0.092)
0.79 (0.031) 0.53 (0.021)
S CATHODE TRIPE
S CATHODE TRIPE
1 NOTES: . ALL DIMENSIONS ARE IN MILLIMETRES (INCHES). 2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD. 3. LEAD POLARITY FOR AlGaAs LAMPS IS OPPOSITE TO THE LEAD POLARITY OF SUBMINIATURE LAMPS USING OTHER TECHNOLOGIES.
CATHODE AB
NO. ANODE DOWN.
YES. CATHODE DOWN.
Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from Shorting to Anode Connection.
|
|
