|Category||Multimedia => Audio => D/A Converters|
|Description||2k / 4kbit EePROM With 2ch 8bit D/A Converter|
|Company||AKM Semiconductor, Inc.|
|Datasheet||Download AK9824 datasheet
The AK9822/24 includes 2 channel, 8 bit D/A converters with on-chip output buffer amps and it is capable to store the input digital data of each D/A converter by on-chip non-volatile CMOS EEPROM. The AK9822/24 is optimally designed for various circuit adjustments for consumer and industrial equipments and it is ideally suited for replacing mechanical trimmers.Feature
EEPROM section AK9822 128 words AK9824 256 words Ő 16bit One chip microcomputer interface Sequential register read D/A Converter section 2 channel Resolution : 8bit Differential Non-Linearity : 1.0 LSB Linearity Error : 1.5 LSB Output Voltage Range : GND VCC Wide VCC operation EEPROM section : 1.8V5.5V D/A Converter Section : 2.7V5.5V Power Down Function
Pin Description No. Pin Name SK DO GND DI VCC AO0 I/O Analog Output Pin Chip Select Pin Serial Clock Pin Serial Data Output Pin Ground Pin Serial Data Input Pin Power Supply Analog Output Pin (Schmitt-trigger input) (Schmitt-trigger input) Function
The AK9822/24 is composed of EEPROM and the 8bit D/A converter of two channels with the output buffer amplifier. The AK9822/24 can connect to the serial communication port of popular one chip microcomputer directly (3 line negative clock synchronous interface). The AK9822/24 takes the data of the DI pin by the rising edge of the SK pin and outputs the data from the DO pin by the falling edge of the SK pin. The AK9822/24 has 7 instructions such as READ, WRITE, WREN, WRDS, PDEN, PDDS and CALL. The AK9822/24 is operated by inputting these instructions from the serial interface. Each instruction is organized by op-code block (8bits), address block (8bits) and data (8bitsŐ2). The DO pin is "Hi-Z" state except that the DO pin outputs the data of the internal register and the status of Ready/Busy. WRITE protection function There are two states such as the WRITE enable state and the WRITE disable state in the AK9822/24. In the WRITE disable state the WRITE instruction becomes invalid and is not executed. When Vcc is applied to the part, the part powers up in the WRITE disable state and the part becomes the WRITE enable state by inputting the WREN instruction. The WRITE enable state continues until the WRDS instruction is executed or Vcc is removed from the part. Execution of a READ instruction is independent of both WREN and WRDS instructions. Power down function There are two modes such as the power down mode and the normal mode in the AK9822/24. When the is in the power down mode, the D/A converter section is in the standby state. At this time, the outputs of the D/A converters become "Hi-Z". When Vcc is applied to the part, the is in the power down mode. When a AUTO READ function is executed, the part becomes the normal mode. After the AUTO READ function is executed, the mode of the part can be switched by the PDEN and PDDS instructions. The AK9822/24 becomes the power down mode by inputting the PDEN instruction. The part is in the power down mode until the PDDS instruction is executed. When the PDDS instruction is executed, the part becomes the normal mode. When returning to the normal mode from the power down mode, the D/A converters output the voltage value set before entering the power down mode. The relation between the D/A converter state and the mode are shown in the table 1. Mode Power down mode Normal mode State of D/A converter standby normalTable 1. The relation between the state of D/A converter and the mode
|Some Part number from the same manufacture AKM Semiconductor, Inc.|
|AK9824M 2K/4Kbit EePROM With 2ch 8bit D/A Converter|
|AK9844 4kbit EePROM With 4ch 8bit D/A Converter|
|AK9844F 4Kbit EePROM With 4ch 8bit D/A Converter|
|AKD2304 Quad PCM Codec/filter Combo Lsi|
|AKD4309B Evaluation Board Rev.a For Ak4309b|
|AKD4316A Evaluation Board|
|AKD4317 Evaluation Board For Ak4317 Rev.a|
|AKD4351 Evaluation Board Rev.b For Ak4351|
|AKD4352 Evaluation Board Rev.a For Ak4352|
|AKD4353 Evaluation Board Rev.a For Ak4353|
|AKD4356 Evaluation Board Rev.b For Ak4356|
|AKD4363 Evaluation Board Rev.a For Ak4363|
|AKD4364 Evaluation Board Rev.a For Ak4364|
|AKD4380 Evaluation Board Rev.a For Ak4380|
|AKD4382 Evaluation Board Rev.a For Ak4382|
|AKD4384 106db 192khz 24-bit 2ch DAC|
|AKD4393 Evaluation Board Rev.c For Ak4393|
|AKD4394 Evaluation Board Rev.c For Ak4394|
|AKD4395 Evaluation Board Rev.c For Ak4395|
|AKD4516A Evaluation Board Rev.a For Ak4516a|
|AKD4520 100db 20bit Stereo ADC & DAC|
AN5394FB : Package =. The is an RGB processor IC which converts the brightness and color difference signals to a primary color signal. It can be connected to each input signal of HDTV (Japan), DVD, NTSC, PAL, VGA, etc. and facilitates rationalization and high performance of the endproducts. Wider band for signal processing (Y: 30 MHz/-3 dB, color difference: 15 MHz/-3 dB) Direct.
GS7005 : Converters. Pro-linx(tm) Complete Serial Digital Video Receiver. DATA SHEET SMPTE 259M-C compliant fully integrated 270 Mb/s SDI receiver integrated cable equalization (100m Belden 8281 typical) low power consumption (750mW typical) operates from to 85°C small footprint with minimal external components Lock and Carrier Detect output indications H timing signal output SMPTE descrambler and NRZI decoder may be disabled.
HDD-1206SM : 12-bit Deglitched Voltage Out D/A Converter.
LTC1098AC : Micropower Sampling 8-bit Serial I/o A/D Converters. 80µA Maximum Supply Current 1nA Typical Supply Current in Shutdown 8-Pin SO Plastic Package 5V Operation (LTC1096/LTC1098) 3V Operation (LTC1096L/LTC1098L)(2.65V Min) Sample-and-Hold 16µs Conversion Time 33kHz Sample Rate ± 0.5LSB Total Unadjusted Error Over Temp Direct 3-Wire Interface to Most MPU Serial Ports and All MPU Parallel I/O Ports The LTC ®1096/LTC1096L/LTC1098/LTC1098L.
M52957FP : Distance Detection Signal Processing For 3V Supply Voltage. DISTANCE DETECTION SIGNAL PROCESSING FOR 3V SUPPLY VOLTAGE is a semiconductor integrated circuit containing distance detection signal processing circuit for 3V supply voltage. This device transforms each optical inflow current I1 and I2 from PSD SENSOR into the voltage, and integrates that output after doing calculation corresponds to I1/(I1+I2), and outputs.
PCM3008T : ti PCM3008, Low Voltage And Low Power Single-ended Analog Input/output 16-Bit Stereo Audio Codec.
PIC16LC711 : 8-bit CMOS Microcontrollers With A/D Converter. Timer0: 8-bit timer/counter with 8-bit prescaler 8-bit multichannel analog-to-digital converter Brown-out detection circuitry for Brown-out Reset (BOR) 13 I/O Pins with Individual Direction Control PIC16C7X Program Memory (EPROM) x 14 Data Memory (Bytes) x 8 I/O Pins Timer Modules A/D Channels In-Circuit Serial Programming Brown-out Reset Interrupt.
TDA4671 : Chroma. Picture Signal Improvement (psi) Circuit. Product Supersedes data of June 1993 File under Integrated Circuits, IC02 1996 Dec 11 Luminance signal delay from 1100 ns (minimum step 45 ns) Luminance signal peaking with symmetrical overshoots selectable Selectable or 5 MHz peaking centre frequency and degree of peaking 0, +3 and +6 dB) Selectable noise reduction by coring Handles negative as well.
TDA7480 : 10W Mono Class D Amplifier. 10W OUTPUT POWER: = 8/4; THD = 10% HIGH EFFICIENCY NO HEATSINK SPLIT SUPPLY OVERVOLTAGE PROTECTION ST-BY AND MUTE SHORT CIRCUIT PROTECTION THERMAL OVERLOAD PROTECTION The is an audio class-D amplifier assembled in Power DIP package specially designed for high efficiency applications mainly for TV and Home Stereo sets. R2 7K ST-BY MUTE -VCC (Pin R3 30K ST-BY/.
TWL1107 : . Handsets, Voice-Enabled Terminals, and Telecommunications Applications to 3.3-V Operation Selectable 13-Bit Linear or 8-Bit A-Law Companded Conversion Differential Microphone Input with External Gain Setting Differential Earphone Output Capable of Driving to 8- Load Programmable Volume Control in Linear Mode Microphone (MIC) and Earphone (EAR) Mute.
U2730B-N : L-band Down-converter Incl. PLL For Dab Receivers. The is a monolithically integrated L-band down-converter circuit fabricated in Atmel Wireless & Microcontrollers' advanced UHF5S technology. This is an improved version of the U2730B-B and covers all functions of an L-band downconverter in a DAB receiver. The device includes a gain controlled amplifier, a gain controlled mixer, an output buffer, a gain.
U4256BM : Frequency Synthesizer For Radio Tuning.
VSP2254GSJ : CCD Imaging Analog Front Ends. ti VSP2254, 2CH, 14-Bit, 36 MSPS CCD Signal Processor For Digital Camera.
YMF753 : AC97 Rev.2.2 Compliant Audio Codec. an AC'97 Audio CODEC LSI, which is fully compliant with the industry standard "Audio CODEC '97" component (Revision 2.2). Different from former AC'97, YMF753 supports new like SPDIF OUT and Zoomed Video Port. Without using a digital controller, these new can be enhanced in the AC'97 sound system that has an ICH controller built-in chipset. Low power.
LM4871 : 3W Audio Power Amplifier with Shutdown Mode The LM4871 is a mono bridged audio power amplifier capable of delivering 3W of continuous average power into a 3 load with less than 10% THD when powered by a 5V power supply . To conserve power in portable applications, the LM4871's micropower shutdown mode (IQ = 0.6µA, typ) is activated when VDD is applied.
ts4909 : A free-form text of the package type. Status The current status of a product: Preview: Product proposal has been announced. Evaluation: The period in which customer samples become available. Active: Product is in volume production., NRND: Not Recommended for New Design, Product is fully available to support existing customers but is not recommended.
TAS5713 : Digital Audio Power Amp The TAS5713 is a 25-W, efficient, digital-audio power amplifier for driving stereo bridge-tied speakers. One serial data input allows processing of up to two discrete audio channels and seamless integration to most digital audio processors and MPEG decoders. The device accepts a wide range of input data and data rates. A fully.
CS35L00 : Low Power Class-D Audio Amplifiers The CS35L00, L01 and L03 are a family of low-power digital audio amplifiers with Cirrus Logic’s proprietary Hybrid Class-D Architecture, designed specifically for today’s mobile applications. Combining the benefits of both linear and switching amplifier technologies, its Hybrid Class-D architecture offers best-in-class.
LM49251 : Stereo Audio Subsystem With Class G Headphone Amplifier And Class D Speaker Amplifier With Speaker Protection The LM49251 is a fully integrated audio subsystem designed for portable handheld applications such as cellular phones. Part of Nationalâ€™s PowerWise family of products, the LM49251 utilizes a high efficiency class G headphone amplifier topology.