|Description||2K/4Kbit EePROM With 2ch 8bit D/A Converter|
|Company||AKM Semiconductor, Inc.|
|Datasheet||Download AK9824M datasheet
The AK9822/24 includes 2 channel, 8 bit D/A converters with on-chip output buffer amps and it is capable to store the input digital data of each D/A converter by on-chip non-volatile CMOS EEPROM. The AK9822/24 is optimally designed for various circuit adjustments for consumer and industrial equipments and it is ideally suited for replacing mechanical trimmers.Feature
EEPROM section AK9822 128 words AK9824 256 words Õ 16bit One chip microcomputer interface Sequential register read D/A Converter section 2 channel Resolution : 8bit Differential Non-Linearity : 1.0 LSB Linearity Error : 1.5 LSB Output Voltage Range : GND VCC Wide VCC operation EEPROM section : 1.8V5.5V D/A Converter Section : 2.7V5.5V Power Down Function
Pin Description No. Pin Name SK DO GND DI VCC AO0 I/O Analog Output Pin Chip Select Pin Serial Clock Pin Serial Data Output Pin Ground Pin Serial Data Input Pin Power Supply Analog Output Pin (Schmitt-trigger input) (Schmitt-trigger input) Function
The AK9822/24 is composed of EEPROM and the 8bit D/A converter of two channels with the output buffer amplifier. The AK9822/24 can connect to the serial communication port of popular one chip microcomputer directly (3 line negative clock synchronous interface). The AK9822/24 takes the data of the DI pin by the rising edge of the SK pin and outputs the data from the DO pin by the falling edge of the SK pin. The AK9822/24 has 7 instructions such as READ, WRITE, WREN, WRDS, PDEN, PDDS and CALL. The AK9822/24 is operated by inputting these instructions from the serial interface. Each instruction is organized by op-code block (8bits), address block (8bits) and data (8bitsÕ2). The DO pin is "Hi-Z" state except that the DO pin outputs the data of the internal register and the status of Ready/Busy. WRITE protection function There are two states such as the WRITE enable state and the WRITE disable state in the AK9822/24. In the WRITE disable state the WRITE instruction becomes invalid and is not executed. When Vcc is applied to the part, the part powers up in the WRITE disable state and the part becomes the WRITE enable state by inputting the WREN instruction. The WRITE enable state continues until the WRDS instruction is executed or Vcc is removed from the part. Execution of a READ instruction is independent of both WREN and WRDS instructions. Power down function There are two modes such as the power down mode and the normal mode in the AK9822/24. When the is in the power down mode, the D/A converter section is in the standby state. At this time, the outputs of the D/A converters become "Hi-Z". When Vcc is applied to the part, the is in the power down mode. When a AUTO READ function is executed, the part becomes the normal mode. After the AUTO READ function is executed, the mode of the part can be switched by the PDEN and PDDS instructions. The AK9822/24 becomes the power down mode by inputting the PDEN instruction. The part is in the power down mode until the PDDS instruction is executed. When the PDDS instruction is executed, the part becomes the normal mode. When returning to the normal mode from the power down mode, the D/A converters output the voltage value set before entering the power down mode. The relation between the D/A converter state and the mode are shown in the table 1. Mode Power down mode Normal mode State of D/A converter standby normalTable 1. The relation between the state of D/A converter and the mode
|Some Part number from the same manufacture AKM Semiconductor, Inc.|
|AK9844 4kbit EePROM With 4ch 8bit D/A Converter|
|AK9844F 4Kbit EePROM With 4ch 8bit D/A Converter|
|AKD2304 Quad PCM Codec/filter Combo Lsi|
|AKD4309B Evaluation Board Rev.a For Ak4309b|
|AKD4316A Evaluation Board|
|AKD4317 Evaluation Board For Ak4317 Rev.a|
|AKD4351 Evaluation Board Rev.b For Ak4351|
|AKD4352 Evaluation Board Rev.a For Ak4352|
|AKD4353 Evaluation Board Rev.a For Ak4353|
|AKD4356 Evaluation Board Rev.b For Ak4356|
|AKD4363 Evaluation Board Rev.a For Ak4363|
|AKD4364 Evaluation Board Rev.a For Ak4364|
|AKD4380 Evaluation Board Rev.a For Ak4380|
|AKD4382 Evaluation Board Rev.a For Ak4382|
|AKD4384 106db 192khz 24-bit 2ch DAC|
|AKD4393 Evaluation Board Rev.c For Ak4393|
|AKD4394 Evaluation Board Rev.c For Ak4394|
|AKD4395 Evaluation Board Rev.c For Ak4395|
|AKD4516A Evaluation Board Rev.a For Ak4516a|
|AKD4520 100db 20bit Stereo ADC & DAC|
|AKD4520A Evaluation Board Rev.b For Ak4520a|
AK4586 : - AK4527 + Dir
AK5385AVF : 114dB 192kHz 24-Bit Enhanced Dual Bit ADC
AKD4316A : Evaluation Board
AKD4116 : 192khz Digital Audio Receiver
AKD4648-C : Stereo Codec with Mic/hp/spk Amplifier
AME7721BEEY500Y : Step-up/step-down 60mA Regulated Charge Pump
AK4145 : Digital BTSC Stereo Encoder
AKD4643 : Stereo Codec with Built-in Mic/hp/rcv/spk Amplifier
CY62138V : 256K X 8 Static RAM. Low voltage range: 2.73.6V Ultra-low active power Low standby power Easy memory expansion with CS1/CS2 and OE TTL-compatible inputs and outputs Automatic power-down when deselected CMOS for optimum speed/power consumption by 99% when addresses are not toggling. The device can be put into standby mode when deselected (CS1 HIGH or CS2 LOW). Writing to the device.
EL2033C : 100 MHZ Buffer Amplifier. Differential gain 0.1% Differential phase 0.1° 100mA continuous output current guaranteed Short circuit protected Wide bandwidth - 100MHz High slew rate - 1200V/µs High input impedance 2M Low quiescent current drain The EL2003C and EL2033C are general purpose monolithic unity gain buffers featuring 100MHz, -3dB bandwidth and 4ns small signal rise time.
GPA-CG2CA : GPS Antenna. This new type of GPS antenna from MITSUMI sticks directly onto automobile windows (front, rear). The specially developed layout places the antenna reception element surface on the adhesive face. Sticking onto glass helps attain reliable performance and simplifies wiring. 1. Outer dimensions: 12.5(H)mm 2. Excellent performance characteristics (NF has risen.
J210 : Single. N-channel Field-effect Transistor. Product File under Discrete Semiconductors, SC07 1997 Dec 01 High speed switching Interchangeability of drain and source connections High impedance. APPLICATIONS Analog switches Choppers, multiplexers and commutators Audio amplifiers. N-channel symmetrical junction field-effect transistor TO-92 (SOT54) package. CAUTION This product is supplied in anti-static.
MCP18480 : The MCP18480 is a –48V Hot Swap Controller With Fully Configurable .
MCSF1 : 1.6mm 2 Pin Ceramic Surface Mount Crystal. Mode of Operation 1=Fundamental 3=Third Overtone Operating Temperature Range to 85°C Load Capacitance S=Series, XX=XXpF (Pico Farads) Frequency Range Frequency Tolerance/Stability C, D Operating Temperature Range "C" Option, "E" Option, "F" Option Aging @ 25°C Storage Temperature Range Load Capacitance "S" Option "XX" Option Shunt Capacitance Insulation.
TSD-800 : Support Products FOR Micro Linear I.c.s. Magnetics Micro Linear's ML4824 Switcher GENERAL APPLICATION ML4824-1 Premier Magnetics' TSD-735 Switch Mode Transformer was designed for use with MICRO LINEAR'S ML4824-1 PFC/PWM Combination off-line controller IC, in the Two Transistor Single-Ended Forward Converter Configuration. This converter topology can provide isolated multiple outputs with efficiencies.
CCF60324KFKE36 : Metal Film Resistors, Industrial, 1% Tolerance. Power Ratings: 1/2, 3/4 and 1 watt ± 100ppm/°C temperature coefficient Superior electrical performance Flame retardant epoxy conformal coating Standard 5 band color code marking for ease of identification after mounting Tape and reel packaging for automatic insertion (52.4mm inside tape spacing per EIA-296-E) Lead (Pb)-Free version is RoHS Compliant.
YB01KW01-12-JD-RO : Switch Hardware INDICATOR AMBER CAP. s: Manufacturer: NKK Switches ; Product Category: Switch Hardware ; RoHS: Details ; For Use With: Pushbutton Switches ; Type: Indicators ; Designed for: YB, YB2 Series ; Body Shape: Square ; Color: Black ; : 12 volt incandescent lamp, LED cap ; Illumination: Illuminated ; Mounting Style: Panel, Bushing Mount.
NRS6020T3R3NMGJ : Fixed Inductors, Coils, Choke 3.3µH 2.75A 0.236" L x 0.236" W x 0.078" H (6.00mm x 6.00mm x 2.00mm) -; INDUCTOR POWER 3.3UH 2.75A SMD. s: Inductance: 3.3µH ; Tolerance: ±30% ; Package / Case: 0.236" L x 0.236" W x 0.078" H (6.00mm x 6.00mm x 2.00mm) ; Packaging: Tape & Reel (TR) ; Type: - ; Current: 2.75A ; Mounting Type: Surface Mount ; Q @ Freq:.
RG1005P-5360-P-T1 : 536 Ohm 0.063W, 1/16W Chip Resistor - Surface Mount; RES 536 OHM 1/16W .02% 0402. s: Resistance (Ohms): 536 ; Power (Watts): 0.063W, 1/16W ; Tolerance: ±0.02% ; Packaging: Tape & Reel (TR) ; Composition: Thin Film ; Temperature Coefficient: ±25ppm/°C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.
CRCW12066K98FKEAHP : 6.98K Ohm 0.5W, 1/2W Chip Resistor - Surface Mount; RES 6.98K OHM .5W 1% 1206 SMD. s: Resistance (Ohms): 6.98K ; Power (Watts): 0.5W, 1/2W ; Tolerance: ±1% ; Packaging: Tape & Reel (TR) ; Composition: Thick Film ; Temperature Coefficient: ±100ppm/°C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.
3009P-1-102 : Ohm Trimmer Potentiometers, Variable Resistors Side Adjustment 15 Turn; TRIMMER 1K OHM 0.75W TH. s: Resistance (Ohms): 1K ; Power (Watts): 0.75W, 3/4W ; Number of Turns: 15 ; Adjustment Type: Side Adjustment ; Tolerance: ±10% ; Mounting Type: Through Hole ; Temperature Coefficient: ±100ppm/°C ; Resistive Material: Cermet ; Packaging: Tube ; Lead Free.
SCA830-D06-1 : Board Mount Accelerometers 1-Axis Acceleromter SPI interface. Murata MEMS Sensors are robust silicon capacitive sensors. Using Murata's 3D MEMS technology, the sensors are very sensitive to inertial forces and pressure, but are insensitive to other environmental variables. The composition of single crystal silicon and glass ensures reliability, accuracy,.
51951-001LF : 28 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER. s: Connector Type: TWO PART BOARD CONNECTOR ; Gender: Male ; Termination Types: SOLDER ; Number of Contacts: 28.