|
|
Part: EPF6024AQC208-1
Category:
FPGAs/PLDs
-> FPGA (Field Programmable Gate Array)
Description: Flex 6000 Device Family (5.0V)
Company: Altera Corporation
Datasheet: Download EPF6024AQC208-1 datasheet File size : 188 kB
Request For quote: Find where to buy EPF6024AQC208-1
Datasheet text preview:
FLEX 6000
®
Programmable Logic Device Family
Data Sheet
March 2001, ver. 4.1
Features...
s
s
s
Provides an ideal low-cost, programmable alternative to highvolume gate array applications and allows fast design changes during prototyping or design testing Product features Register-rich, look-up table- (LUT-) based architecture OptiFLEX® architecture that increases device area efficiency Typical gates ranging from 5,000 to 24,000 gates (see Table 1) Built-in low-skew clock distribution tree 100% functional testing of all devices; test vectors or scan chains are not required System-level features In-circuit reconfigurability (ICR) via external configuration device or intelligent controller 5.0-V devices are fully compliant with peripheral component interconnect Special Interest Group (PCI SIG) PCI Local Bus Specification, Revision 2.2 Built-in Joint Test Action Group (JTAG) boundary-scan test (BST) circuitry compliant with IEEE Std. 1149.1-1990, available without consuming additional device logic MultiVoltTM I/O interface operation, allowing a device to bridge between systems operating at different voltages Low power consumption (typical specification less than 0.5 mA in standby mode) 3.3-V devices support hot-socketing
Table 1. FLEX 6000 Device Features Feature
Typical gates (1) Logic elements (LEs) Maximum I/O pins Supply voltage (VCCINT) Note:
( 1) The embedded IEEE Std. 1149.1 JTAG circuitry adds up to 14,000 gates in addition to the listed typical gates.
EPF6010A
10, 000 880 102 3. 3 V
EPF6016
16, 000 1,320 204 5. 0 V
EPF6016A
16, 000 1,320 171 3. 3 V
EPF6024A
24, 000 1,960 218 3. 3 V
Altera Corporation
A-DS-F6000-04.1
1
FLEX 6000 Programmable Logic Device Family Data Sheet
...and More Features
s
s
s
s
s
Powerful I/O pins Individual tri-state output enable control for each pin Programmable output slew-rate control to reduce switching noise Fast path from register to I/O pin for fast clock-to-output time Flexible interconnect FastTrack® Interconnect continuous routing structure for fast, predictable interconnect delays Dedicated carry chain that implements arithmetic functions such as fast adders, counters, and comparators (automatically used by software tools and megafunctions) Dedicated cascade chain that implements high-speed, high-fanin logic functions (automatically used by software tools and megafunctions) Tri-state emulation that implements internal tri-state networks Four low-skew global paths for clock, clear, preset, or logic signals Software design support and automatic place-and-route provided by Altera's development system for Windows-based PCs, Sun SPARCstations, and HP 9000 Series 700/800 Flexible package options Available in a variety of packages with 100 to 256 pins, including the innovative FineLine BGATM packages (see Table 2) SameFrameTM pin-compatibility (with other FLEX® 6000 devices) across device densities and pin counts Thin quad flat pack (TQFP), plastic quad flat pack (PQFP), and ball-grid array (BGA) packages (see Table 2) Footprint- and pin-compatibility with other FLEX 6000 devices in the same package Additional design entry and simulation support provided by EDIF 2 0 0 and 3 0 0 netlist files, the library of parameterized modules (LPM), Verilog HDL, VHDL, DesignWare components, and other interfaces to popular EDA tools from manufacturers such as Cadence, Exemplar Logic, Mentor Graphics, OrCAD, Synopsys, Synplicity, VeriBest, and Viewlogic
Table 2. FLEX 6000 Package Options & I/O Pin Count Device
EP F 6010A EP F 6016 EP F 6016A EP F 6024A 81 81
100-Pin TQFP
71
100-Pin FineLine BGA
144-Pin TQFP
102 117 117 117
208-Pin PQFP
171 171 171
240-Pin PQFP
199 199
256-Pin BGA
204
256-pin FineLine BGA
171 218 219
2
Altera Corporation
FLEX 6000 Programmable Logic Device Family Data Sheet
General Description
The Altera® FLEX 6000 programmable logic device (PLD) family provides a low-cost alternative to high-volume gate array designs. FLEX 6000 devices are based on the OptiFLEX architecture, which minimizes die size while maintaining high performance and routability. The devices have reconfigurable SRAM elements, which give designers the flexibility to quickly change their designs during prototyping and design testing. Designers can also change functionality during operation via in-circuit reconfiguration. FLEX 6000 devices are reprogrammable, and they are 100% tested prior to shipment. As a result, designers are not required to generate test vectors for fault coverage purposes, allowing them to focus on simulation and design verification. In addition, the designer does not need to manage inventories of different gate array designs. FLEX 6000 devices are configured on the board for the specific functionality required. Table 3 shows FLEX 6000 performance for some common designs. All performance values shown were obtained using Synopsys DesignWare or LPM functions. Special design techniques are not required to implement the applications; the designer simply infers or instantiates a function in a Verilog HDL, VHDL, Altera Hardware Description Language (AHDL), or schematic design file.
Table 3. FLEX 6000 Device Performance for Common Designs Application LEs Used -1 Speed Grade
16-bit loadable counter 16-bit accumulator 24-bit accumulator 16-to-1 multiplexer (pin-to-pin) (1) 16 × 16 multiplier with a 4-stage pipeline N ot e :
(1) This performance value is measured as a pin-to-pin delay.
Performance -2 Speed Grade
153 153 123 13. 4 67
Units -3 Speed Grade
133 133 108 16.6 58 MHz MHz MHz ns MHz
16 16 24 10 592
172 172 136 12. 1 84
Altera Corporation
3
FLEX 6000 Programmable Logic Device Family Data Sheet
Table 4 shows FLEX 6000 performance for more complex designs. Table 4. FLEX 6000 Device Performance for Complex Designs Application LEs Used -1 Speed Grade
8-bit, 16-tap parallel finite impulse response (FIR) filter 8-bit, 512-point fast Fourier transform (FFT) function a16450 universal asynchronous receiver/transmitter (UART) PCI bus target with zero wait states Note:
( 1)
Note (1) Performance -2 Speed Grade
80 89 53 30 49
Units -3 Speed Grade
72 109 43 25 42 MSPS
5 99 1,182 4 87 6 09
94 75 63 36 56
µS M Hz
M Hz M Hz
The applications in this table were created using Altera MegaCoreTM functions.
FLEX 6000 devices are supported by Altera development systems; a single, integrated package that offers schematic, text (including AHDL), and waveform design entry, compilation and logic synthesis, full simulation and worst-case timing analysis, and device configuration. The Altera software provides EDIF 2 0 0 and 3 0 0, LPM, VHDL, Verilog HDL, and other interfaces for additional design entry and simulation support from other industry-standard PC- and UNIX workstation-based EDA tools. The Altera software works easily with common gate array EDA tools for synthesis and simulation. For example, the Altera software can generate Verilog HDL files for simulation with tools such as Cadence Verilog-XL. Additionally, the Altera software contains EDA libraries that use devicespecific features such as carry chains which are used for fast counter and arithmetic functions. For instance, the Synopsys Design Compiler library supplied with the Altera development systems include DesignWare functions that are optimized for the FLEX 6000 architecture. The Altera development system runs on Windows-based PCs, Sun SPARCstations, and HP 9000 Series 700/800.
f
See the MAX+PLUS II Programmable Logic Development System & Software Data Sheet and the Quartus Programmable Logic Development System & Software Data Sheet for more information.
4
Altera Corporation
FLEX 6000 Programmable Logic Device Family Data Sheet
Functional Description
The FLEX 6000 OptiFLEX architecture consists of logic elements (LEs). Each LE includes a 4-input look-up table (LUT), which can implement any 4-input function, a register, and dedicated paths for carry and cascade chain functions. Because each LE contains a register, a design can be easily pipelined without consuming more LEs. The specified gate count for FLEX 6000 devices includes all LUTs and registers. LEs are combined into groups called logic array blocks (LABs); each LAB contains 10 LEs. The Altera software automatically places related LEs into the same LAB, minimizing the number of required interconnects. Each LAB can implement a medium-sized block of logic, such as a counter or multiplexer. Signal interconnections within FLEX 6000 devices--and to and from device pins--are provided via the routing structure of the FastTrack Interconnect. The routing structure is a series of fast, continuous row and column channels that run the entire length and width of the device. Any LE or pin can feed or be fed by any other LE or pin via the FastTrack Interconnect. See "FastTrack Interconnect" on page 17 of this data sheet for more information. Each I/O pin is fed by an I/O element (IOE) located at the end of each row and column of the FastTrack Interconnect. Each IOE contains a bidirectional I/O buffer. Each IOE is placed next to an LAB, where it can be driven by the local interconnect of that LAB. This feature allows fast clock-to-output times of less than 8 ns when a pin is driven by any of the 10 LEs in the adjacent LAB. Also, any LE can drive any pin via the row and column interconnect. I/O pins can drive the LE registers via the row and column interconnect, providing setup times as low as 2 ns and hold times of 0 ns. IOEs provide a variety of features, such as JTAG BST support, slew-rate control, and tri-state buffers. Figure 1 shows a block diagram of the FLEX 6000 OptiFLEX architecture. Each group of ten LEs is combined into an LAB, and the LABs are arranged into rows and columns. The LABs are interconnected by the FastTrack Interconnect. IOEs are located at the end of each FastTrack Interconnect row and column.
Altera Corporation
5
Others parts begin by ep
EP-1 EP-2 EP-3 EP-4 EP-5 EP-6 EP-7 EP-8 EP-9 EP-10 EP-11 EP-12 EP-13 EP-14 EP-15 EP-16 EP-17 EP-18 EP-19 EP-20 EP-21 EP-22 EP-23 EP-24 EP-25 EP-26 EP-27 EP-28 EP-29 EP-30 EP-31 EP-32 EP-33 EP-34 EP-35 EP-36 EP-37 EP-38 EP-39 EP-40 EP-41
|
|
|
