Details, datasheet, quote on part number: AD5241-1M
CategoryAnalog & Mixed-Signal Processing
DescriptionSingle-Channel, I2C Compatible, 256 Position, Digital Potentiometer
CompanyAnalog Devices
DatasheetDownload AD5241-1M datasheet


Features, Applications

FEATURES 256 Position , 100 Low Tempco 30 ppm/ C Internal Power ON Midscale Preset Single Supply V or Dual Supply 2.7 V for AC or Bipolar Operation I2C-Compatible Interface with Reaback Capability Extra Programmable Logic Outputs APPLICATIONS Multimedia, Video and Audio Communications Mechanical Potentiometer Replacement Instrumentation: Gain, Offset Adjustment Programmable Voltage-to-Current Conversion Line Impedance Matching GENERAL DESCRIPTION

The AD5241/AD5242 provides a single-/dual-channel, 256position digitally controlled variable resistor (VR) device. These devices perform the same electronic adjustment function as a potentiometer, trimmer or variable resistor. Each VR offers a completely programmable value of resistance, between the A terminal and the wiper, or the B terminal and the wiper. For AD5242, the fixed A-to-B terminal resistance 1 M has a 1% channel-to-channel matching tolerance. Nominal temperature coefficient of both parts is 30 ppm/C. Wiper position programming defaults to midscale at system power ON. Once powered, the VR wiper position is programmed I2C-compatible 2-wire serial data interface. Both parts have available two extra programmable logic outputs that enable users to drive digital loads, logic gates, LED drivers, and analog switches in their system. The AD5241/AD5242 is available in surface-mount (SO-14/-16) packages and, for ultracompact solutions, TSSOP-14/-16 packages. All parts are guaranteed to operate over the extended industrial temperature range to +85C. For 3-wire, SPI-compatible interface applications, please refer AD8400, AD8402, and AD8403 products.

*Nonvolatile digital potentiometer. is a registered trademark of Philips Corporation.

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 Fax: 781/326-8703 Analog Devices, Inc., 2002

Conditions Min Typ1 Max Unit LSB % ppm/C Bits LSB ppm/C LSB A W kHz % s nVHz

DC CHARACTERISTICS, RHEOSTAT MODE (Specifications apply to all VRs.) Resistor Differential Nonlinearity 2 R-DNL RWB, = NC Resistor Integral Nonlinearity2 R-INL RWB, = NC Nominal Resistor Tolerance = 25C, RAB = 25C, RAB k/1 M Resistance Temperature Coefficient RAB/T VAB = VDD, Wiper = No Connect Wiper Resistance IW = VDD /R, VDD V DC CHARACTERISTICS, POTENTIOMETER DIVIDER MODE (Specifications apply to all VRs.) Resolution N Differential Nonlinearity3 DNL Integral Nonlinearity3 INL Voltage Divider Temperature Coefficient VW/T Code = 80H Full-Scale Error VWFSE Code = FFH Zero-Scale Error VWZSE Code = 00H RESISTOR TERMINALS Voltage Capacitance5 W Common-Mode Leakage DIGITAL INPUTS Input Logic High (SDA and SCL) Input Logic Low (SDA and SCL) Input Logic High (AD0 and AD1) Input Logic Low (AD0 and AD1) Input Logic High Input Logic Low Input Current Input Capacitance5 DIGITAL OUTPUT Output Logic Low (SDA) Output Logic Low (O1 and O2) Output Logic High (O1 and O2) Three-State Leakage Current (SDA) Output Capacitance5 POWER SUPPLIES Power Single-Supply Range Power Dual-Supply Range Positive Supply Current Negative Supply Current Power Dissipation6 Power Supply Sensitivity DYNAMIC 7, 8 Bandwidth 3 dB VA, B, W CA, B CW ICM VIH VIL VIH VIL VIH VIL IIL CIL VOL VOH IOZ COZ VDD RANGE VDD/SS RANGE IDD ISS PDISS PSS BW_1 M THDW tS eN_WB

= 1 MHz, Measured to GND, Code = 1 MHz, Measured to GND, Code VW 0.7 VDD

0.01 RAB 10 k, Code = 80H RAB 100 k, Code = 80H RAB 1 M, Code 1 V rms 2 V dc, 2 V dc, = 1 kHz VA = VDD, 1 LSB Error Band, RAB 10 k RWB = 1 kHz

Total Harmonic Distortion VW Settling Time Resistor Noise Voltage

INTERFACE TIMING CHARACTERISTICS (Applies to all parts. ) SCL Clock Frequency fSCL tBUF Bus Free Time Between t1 STOP and START tHD; STA Hold Time (Repeated START) t2 After this period the first clock pulse is generated. tLOW Low Period of SCL Clock t3 tHIGH High Period of SCL Clock t4 tSU; STA Setup Time for START Condition t5 t6 tHD; DAT Data Hold Time tSU; DAT Data Setup Time t7 tR Rise Time of Both t8 SDA and SCL Signals tF Fall Time of Both SDA and SCL Signals t9 tSU; STO Setup Time for STOP Condition t10

NOTES 1 Typicals represent average readings at 25 C, VDD V. 2 Resistor position nonlinearity error R-INL is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic. See Figure 10 test circuit. 3 INL and DNL are measured V W with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. A = VDD and 0 V. DNL specification limits 1 LSB maximum are Guaranteed Monotonic operating conditions. See Figure 9 test circuit. 4 Resistor terminals B, W have no limitations on polarity with respect to each other. 5 Guaranteed by design and not subject to production test. 6 PDISS is calculated from (IDD VDD). CMOS logic level inputs result in minimum power dissipation. 7 Bandwidth, noise, and settling time are dependent on the terminal resistance value chosen. The lowest R value results in the fastest settling time and highest bandwidth. The highest R value results in the minimum overall power consumption. 8 All dynamic characteristics use V. 9 See timing diagram for location of measured values. Specifications subject to change without notice.


Related products with the same datasheet
Some Part number from the same manufacture Analog Devices
AD5241BR10 Single-Channel, I2C Compatible, 256 Position, Digital Potentiometer
AD5243 256-Position Dual Channel I2C Compatible Digital Potentiometer
AD5245 256 Position I2C Compatible Digital Potentiometer
AD5246 128 Position I2C Compatible Programmable Resistor in SC70 Package
AD5247 128 Position I2C Compatible Digital Potentiometer in SC70 Package
AD5248 256-Position Dual Channel I2C Compatible Digital Resistor
AD524A Precision Monolithic Instrumentation Amplifier
AD524AD Precision Instrumentation Amplifier
AD524AE Precision Monolithic Instrumentation Amplifier
AD524B Precision Instrumentation Amplifier
AD524BD Precision Monolithic Instrumentation Amplifier
AD524C Precision Instrumentation Amplifier
AD524CD Precision Monolithic Instrumentation Amplifier
AD524S Precision Instrumentation Amplifier
AD524SCHIPS Precision Monolithic Instrumentation Amplifier
AD5251 I2C, Nonvolatile Memory, Dual 64-Position Digital Potentiometer

AME8501AEFTCD28 : 3-Pin/5-Pin Micropower P Reset Family

OP213EP : Low Noise, Low Drift Single-supply Operational Amplifiers

ADCMP604BKSZ-RL : ADCMP604 - Rail-to-Rail, Very Fast, 2.5 V to 5.5 V, Single-Supply LVDS Comparator in a 6-lead SC70 Package. Product Description The ADCMP604 and ADCMP605 are very fast comparators fabricated on Analog Devices proprietary XFCB2 process. These comparators are exceptionally versatile an

ADR06BUJ-R2 : Ultracompact, Precision 10.0 V Voltage References The ADR01, ADR02, ADR03, and ADR06 are precision 10.0 V, 5.0 V, 2.5 V, and 3.0 V band gap voltage references featuring high accuracy, high stability, and low power. The parts are housed in tiny, 5-lead SC70 and TSOT packages, as well as in 8-lead SO

AD7847AR883B : Lc2mos Complete, Dual 12-bit Mdacs

AD7862ARS-2REEL : Data Acquisition - Analog To Digital Converter (adc) Integrated Circuit (ics) 4 Single-Ended, Unipolar Tape & Reel (TR) Analog and Digital; IC ADC 12BIT DUAL 250KSPS 28SSOP Specifications: Number of Bits: 12 ; Package / Case: 28-SSOP (0.209", 5.30mm Width) ; Data Interface: Parallel ; Packaging: Tape & Reel (TR) ; Sampling Rate (Per Second): 250k ; Operating Temperature: -40C ~ 85C ; Voltage Supply Source: Analog and Digital ; Number of Inputs and Type: 4 Single-

ADP3335ARM-2.85-RL : 1.8 V FIXED POSITIVE LDO REGULATOR, 0.37 V DROPOUT, PDSO8 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, 3 X 3 MM, LFCSP-8 ; Life Cycle Stage: ACTIVE ; Output Voltage: 1.76 to 1.84 volts ; IOUT: 0.5000 amps ; VIN: 2.6 to 12 volts ; Dropout Voltage: 0.3700 volts

ADSP-BF542KBCZ-6A : 16-BIT, 50 MHz, OTHER DSP, PBGA316 Specifications: Data Bus: 40 ; Supply Voltage: 1 ; Package Type: Other, LEAD FREE, MO-205AM, MBGA-316 ; Pin Count: 316 ; Clock Speed: 50 MHz ; Operating Temperature: -40 to 105 C (-40 to 221 F) ; External Memory Interface: 16-Bit

0-C     D-L     M-R     S-Z