|
Details, datasheet, quote on part number:AD603AR-REEL
| |
Datasheet text preview:
a
FEATURES "Linear in dB" Gain Control Pin Programmable Gain Ranges 11 dB to +31 dB with 90 MHz Bandwidth +9 dB to +51 dB with 9 MHz Bandwidth Any Intermediate Range, e.g., 1 dB to +41 dB with 30 MHz Bandwidth Bandwidth Independent of Variable Gain 1.3 nV/Hz Input Noise Spectral Density 0.5 dB Typical Gain Accuracy MIL-STD-883 Compliant and DESC Versions Available APPLICATIONS RF/IF AGC Amplifier Video Gain Control A/D Range Extension Signal Measurement PRODUCT DESCRIPTION
Low Noise, 90 MHz Variable-Gain Amplifier AD603*
1 V to span the central 40 dB of the gain range. An over- and under-range of 1 dB is provided whatever the selected range. The gain-control response time is less than 1 µs for a 40 dB change. The differential gain-control interface allows the use of either differential or single-ended positive or negative control voltages. Several of these amplifiers may be cascaded and their gain-control gains offset to optimize the system S/N ratio. The AD603 can drive a load impedance as low as 100 with low distortion. For a 500 load in shunt with 5 pF, the total harmonic distortion for a ± 1 V sinusoidal output at 10 MHz is typically 60 dBc. The peak specified output is ± 2.5 V minimum into a 500 load, or ± 1 V into a 100 load. The AD603 uses a proprietary circuit topology--the X-AMPTM. The X-AMP comprises a variable attenuator of 0 dB to 42.14 dB followed by a fixed-gain amplifier. Because of the attenuator, the amplifier never has to cope with large inputs and can use negative feedback to define its (fixed) gain and dynamic performance. The attenuator has an input resistance of 100 , laser trimmed to ± 3%, and comprises a seven-stage R-2R ladder network, resulting in an attenuation between tap points of 6.021 dB. A proprietary interpolation technique provides a continuous gain-control function which is linear in dB. The AD603A is specified for operation from 40°C to +85°C and is available in both 8-lead SOIC (R) and 8-lead ceramic DIP (Q). The AD603S is specified for operation from 55°C to +125°C and is available in an 8-lead ceramic DIP (Q). The AD603 is also available under DESC SMD 5962-94572.
The AD603 is a low noise, voltage-controlled amplifier for use in RF and IF AGC systems. It provides accurate, pin selectable gains of 11 dB to +31 dB with a bandwidth of 90 MHz or +9 dB to +51 dB with a bandwidth of 9 MHz. Any intermediate gain range may be arranged using one external resistor. The input referred noise spectral density is only 1.3 nV/Hz and power consumption is 125 mW at the recommended ±5 V supplies. The decibel gain is "linear in dB," accurately calibrated, and stable over temperature and supply. The gain is controlled at a high impedance (50 M), low bias (200 nA) differential input; the scaling is 25 mV/dB, requiring a gain-control voltage of only
FUNCTIONAL BLOCK DIAGRAM
VPOS VNEG GPOS
SCALING REFERENCE
PRECISION PASSIVE INPUT ATTENUATOR
FIXED GAIN AMPLIFIER VOUT
VG GNEG GAIN CONTROL INTERFACE
AD603
6.44k * FDBK 694 *
0dB VINP
6.02dB 12.04dB 18.06dB 24.08dB 30.1dB 36.12dB 42.14dB R 2R R 2R R 2R R 2R R 2R R 2R R R *NORMAL VALUES 20 *
COMM R = 2R LADDER NETWORK
* Patented. X-AMP is a trademark of Analog Devices, Inc.
REV. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2000
C, 5 mV V +500 mV, GNEG AD603SPECIFICATIONS (R@nTge= R+25 500V =, and V, 500pF, unlessotherwise noted.)= 0 V, 10 dB to +30 dB Gain a,= C =5
A S G L L
Model Parameter INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Noise Spectral Density1 Noise Figure 1 dB Compression Point Peak Input Voltage OUTPUT CHARACTERISTICS 3 dB Bandwidth Slew Rate Peak Output2 Output Impedance Output Short-Circuit Current Group Delay Change vs. Gain Group Delay Change vs. Frequency Differential Gain Differential Phase Total Harmonic Distortion 3rd Order Intercept ACCURACY Gain Accuracy TMIN to TMAX Output Offset Voltage3 TMIN to TMAX Output Offset Variation vs. VG TMIN to TMAX GAIN CONTROL INTERFACE Gain Scaling Factor TMIN to TMAX GNEG, GPOS Voltage Range4 Input Bias Current Input Offset Current Differential Input Resistance Response Rate POWER SUPPLY Specified Operating Range Quiescent Current TMIN to TMAX
Conditions Pins 3 to 4 Input Short Circuited f = 10 MHz, Gain = max, RS = 10 f = 10 MHz, Gain = max, RS = 10
Min 97
AD603 Typ Max 100 2 1.3 8.8 11 ± 1.4 90 275 ± 3.0 2 50 ±2 ±2 0.2 0.2 60 15 ± 0.5 1 ± 1.5 20 30 20 30 40.6 42 +2.0 103
Unit pF nV/H z dB dBm V MHz V/µs V mA ns ns % Degree dBc dBm dB dB mV mV mV mV dB/V dB/V V nA nA M dB/µs V mA mA
±2
VOUT = 100 mV rms RL 500 RL 500 f 10 MHz f = 3 MHz; Full Gain Range VG = 0 V; f = 1 MHz to 10 MHz f = 10 MHz, VOUT = 1 V rms f = 40 MHz, Gain = max, RS = 50 500 mV VG +500 mV VG = 0 V 500 mV VG +500 mV
± 2.5
39.4 38 1.2
40
Pins 1 to 2 Full 40 dB Gain Change ± 4.75
200 10 50 40 ± 6.3 17 20
12.5
NOTES 1 Typical open or short-circuited input; noise is lower when system is set to maximum gain and input is short-circuited. This figure includes the effects of both voltage and current noise sources. 2 Using resistive loads of 500 or greater, or with the addition of a 1 k pull-down resistor when driving lower loads. 3 The dc gain of the main amplifier in the AD603 is ×35.7; thus, an input offset of 100 µV becomes a 3.57 mV output offset. 4 GNEG and GPOS, gain control, voltage range is guaranteed to be within the range of VS + 4.2 V to +VS 3.4 V over the full temperature range of 40°C to +85°C. Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min and max specifications are guaranteed, although only those shown in boldface are tested on all production units. Specifications subject to change without notice.
2
REV. C
AD603
ABSOLUTE MAXIMUM RATINGS 1
Supply Voltage ± V S . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 7 . 5 V Internal Voltage VINP (Pin 3) . . . . . . . . . . . ± 2 V Continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± VS for 10 ms GPOS, GNEG (Pins 1, 2) . . . . . . . . . . . . . . . . . . . . . . . ± VS Internal Power Dissipation2 . . . . . . . . . . . . . . . . . . . . 400 mW Operating Temperature Range AD603A . . . . . . . . . . . . . . . . . . . . . . . . . . . 40°C to +85°C AD603S . . . . . . . . . . . . . . . . . . . . . . . . . . 55°C to +125°C Storage Temperature Range . . . . . . . . . . . . 65°C to +150°C Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C
NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Thermal Characteristics: 8-Lead SOIC Package: JA = 155°C/W, JC = 33°C/W 8-Lead Ceramic Package: JA = 140°C/W, JC = 15°C/W
PIN FUNCTION DESCRIPTIONS
Pin Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8
Mnemonic GPOS GNEG VINP COMM FDBK VNEG VOUT VPOS
Description Gain-Control Input "HI" (Positive Voltage Increases Gain) Gain-Control Input "LO" (Negative Voltage Increases Gain) Amplifier Input Amplifier Ground Connection to Feedback Network Negative Supply Input Amplifier Output Positive Supply Input
CONNECTION DIAGRAMS 8-Lead Plastic SOIC (R) Package 8-Lead Ceramic DIP (Q) Package
GPOS 1 GNEG 2
8
VPOS
VOUT TOP VIEW VINP 3 (Not to Scale) 6 VNEG
7 5
AD603
COMM 4
FDBK
ORDERING GUIDE Part Number AD603AR AD603AQ AD603SQ/883B * AD603-EB AD603ACHIPS AD603AR-REEL AD603AR-REEL7 Temperature Range 40°C to +85°C 40°C to +85°C 55°C to +125°C 40°C to +85°C 40°C to +85°C 40°C to +85°C Package Description 8-Lead SOIC 8-Lead Ceramic DIP 8-Lead Ceramic DIP Evaluation Board Die 13" Reel 7" Reel Package Option SO-8 Q-8 Q-8
SO-8 SO-8
*Refer to AD603 Military data sheet. Also available as 5962-9457203MPA.
CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD603 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. C
3
AD603
THEORY OF OPERATION
The AD603 comprises a fixed-gain amplifier, preceded by a broadband passive attenuator of 0 dB to 42.14 dB, having a gain-control scaling factor of 40 dB per volt. The fixed gain is laser-trimmed in two ranges, to either 31.07 dB (×35.8) or 50 dB (×358), or may be set to any range in between using one external resistor between Pins 5 and 7. Somewhat higher gain can be obtained by connecting the resistor from Pin 5 to common, but the increase in output offset voltage limits the maximum gain to about 60 dB. For any given range, the bandwidth is independent of the voltage-controlled gain. This system provides an under- and overrange of 1.07 dB in all cases; for example, the overall gain is 11.07 dB to 31.07 dB in the maximum-bandwidth mode (Pin 5 and Pin 7 strapped). This X-AMP structure has many advantages over former methods of gain-control based on nonlinear elements. Most importantly, the fixed-gain amplifier can use negative feedback to increase its accuracy. Since large inputs are first attenuated, the amplifier input is always small. For example, to deliver a ± 1 V output in the 1 dB/+41 dB mode (that is, using a fixed amplifier gain of 41.07 dB) its input is only 8.84 mV; thus the distortion can be very low. Equally important, the small-signal gain and phase response, and thus the pulse response, are essentially independent of gain. Figure 1 is a simplified schematic. The input attenuator is a seven-section R-2R ladder network, using untrimmed resistors of nominally R = 62.5 , which results in a characteristic resistance of 125 ± 20%. A shunt resistor is included at the input and laser trimmed to establish a more exact input resistance of 100 ± 3%, which ensures accurate operation (gain and HP corner frequency) when used in conjunction with external resistors or capacitors. The nominal maximum signal at input VINP is 1 V rms (± 1.4 V peak) when using the recommended ± 5 V supplies, although operation to ± 2 V peak is permissible with some increase in HF distortion and feedthrough. Pin 4 (SIGNAL COMMON) must be connected directly to the input ground; significant impedance in this connection will reduce the gain accuracy. The signal applied at the input of the ladder network is attenuated by 6.02 dB by each section; thus, the attenuation to each of the taps is progressively 0 dB, 6.02 dB, 12.04 dB, 18.06 dB, 24.08 dB, 30.1 dB, 36.12 dB and 42.14 dB. A unique circuit technique is employed to interpolate between these tap-points,
indicated by the "slider" in Figure 1, thus providing continuous attenuation from 0 dB to 42.14 dB. It will help, in understanding the AD603, to think in terms of a mechanical means for moving this slider from left to right; in fact, its "position" is controlled by the voltage between Pins 1 and 2. The details of the gaincontrol interface are discussed later. The gain is at all times very exactly determined, and a linear-indB relationship is automatically guaranteed by the exponential nature of the attenuation in the ladder network (the X-AMP principle). In practice, the gain deviates slightly from the ideal law, by about ± 0.2 dB peak (see, for example, Figure 16).
Noise Performance
An important advantage of the X-AMP is its superior noise performance. The nominal resistance seen at inner tap points is 41.7 (one third of 125 ), which exhibits a Johnson noisespectral density (NSD) of 0.83 nV/Hz (that is, 4kTR) at 27°C, which is a large fraction of the total input noise. The first stage of the amplifier contributes a further 1 nV/Hz, for a total input noise of 1.3 nV/Hz. It will be apparent that it is essential to use a low resistance in the ladder network to achieve the very low specified noise level. The signal's source impedance forms a voltage divider with the AD603's 100 input resistance. In some applications, the resulting attenuation may be unacceptable, requiring the use of an external buffer or preamplifier to match a high impedance source to the low impedance AD603. The noise at maximum gain (that is, at the 0 dB tap) depends on whether the input is short-circuited or open-circuited: when shorted, the minimum NSD of slightly over 1 nV/Hz is achieved; when open, the resistance of 100 looking into the first tap generates 1.29 nV/Hz, so the noise increases to a total of 1.63 nV/Hz. (This last calculation would be important if the AD603 were preceded by, for example, a 900 resistor to allow operation from inputs up to 10 V rms.) As the selected tap moves away from the input, the dependence of the noise on source impedance quickly diminishes. Apart from the small variations just discussed, the signal-tonoise (S/N) ratio at the output is essentially independent of the attenuator setting. For example, on the 11 dB/+31 dB range the fixed gain of ×35.8 raises the output NSD to 46.5 nV/Hz. Thus, for the maximum undistorted output of 1 V rms and a 1 MHz bandwidth, the output S/N ratio would be 86.6 dB, that is, 20 log (1 V/46.5 µV).
VPOS VNEG GPOS
SCALING REFERENCE
PRECISION PASSIVE INPUT ATTENUATOR
FIXED GAIN AMPLIFIER VOUT
VG GNEG GAIN CONTROL INTERFACE
AD603
6.44k * FDBK 694 *
0dB VINP
6.02dB 12.04dB 18.06dB 24.08dB 30.1dB 36.12dB 42.14dB R 2R R 2R R 2R R 2R R 2R R 2R R R *NORMAL VALUES 20 *
COMM R = 2R LADDER NETWORK
Figure 1. Simplified Block Diagram of the AD603
4
REV. C
AD603
The Gain-Control Interface
The attenuation is controlled through a differential, highimpedance (50 M) input, with a scaling factor which is laser-trimmed to 40 dB per volt, that is, 25 mV/dB. An internal bandgap reference ensures stability of the scaling with respect to supply and temperature variations. When the differential input voltage VG = 0 V, the attenuator "slider" is centered, providing an attenuation of 21.07 dB. For the maximum bandwidth range, this results in an overall gain of 10 dB (= 21.07 dB + 31.07 dB). When the control input is 500 mV, the gain is lowered by 20 dB (= 0.500 V × 40 dB/V), to 10 dB; when set to +500 mV, the gain is increased by 20 dB, to 30 dB. When this interface is overdriven in either direction, the gain approaches either 11.07 dB (= 42.14 dB + 31.07 dB) or 31.07 dB (= 0 + 31.07 dB), respectively. The only constraint on the gain-control voltage is that it be kept within the common-mode range (1.2 V to +2.0 V assuming +5 V supplies) of the gain control interface. The basic gain of the AD603 can thus be calculated using the following simple expression: Gain (dB) = 40 VG + 10 (1) where VG is in volts. When Pins 5 and 7 are strapped (see next section) the gain becomes Gain (dB) = 40 VG + 20 for 0 to +40 dB and Gain (dB) = 40 VG + 30 for +10 to +50 dB (2) The high impedance gain-control input ensures minimal loading when driving many amplifiers in multiple channel or cascaded applications. The differential capability provides flexibility in choosing the appropriate signal levels and polarities for various control schemes. For example, if the gain is to be controlled by a DAC providing a positive only ground-referenced output, the "Gain Control LO" (GNEG) pin should be biased to a fixed offset of +500 mV, to set the gain to 10 dB when "Gain Control HI" (GPOS) is at zero, and to 30 dB when at +1.00 V. It is a simple matter to include a voltage divider to achieve other scaling factors. When using an 8-bit DAC having an FS output of +2.55 V (10 mV/bit), a divider ratio of 2 (generating 5 mV/bit) would result in a gain-setting resolution of 0.2 dB/bit. The use of such offsets is valuable when two AD603s are cascaded, when various options exist for optimizing the S/N profile, as will be shown later.
Programming the Fixed-Gain Amplifier Using Pin Strapping
DECIBELS
VC1
GPOS
VPOS
VPOS
AD603
VC2 GNEG VOUT VNEG VNEG VOUT
VIN
VINP
COMM
FDBK
a. 10 dB to +30 dB; 90 MHz Bandwidth
VC1 GPOS VPOS VPOS
AD603
VC2 GNEG VOUT VNEG VNEG 2.15k 5 COMM FDBK .6pF VOUT
VIN
VINP
b. 0 dB to +40 dB; 30 MHz Bandwidth
VC1 GPOS VPOS VPOS
AD603
VC2 GNEG VOUT VNEG VNEG VOUT
VIN
VINP
COMM
FDBK 18pF
c. +10 dB to +50 dB; 9 MHz Bandwidth Figure 2. Pin Strapping to Set Gain
52 50 48 46 44 42 40 38 36 34 32 30 10 100 1k REXT 10k 100k 1M 2:VdB (OUT) VdB (OUT) 1:VdB (OUT)
Access to the feedback network is provided at Pin 5 (FDBK). The user may program the gain of the AD603's output amplifier using this pin, as shown in Figure 2. There are three modes: in the default mode, FDBK is unconnected, providing the range +9 dB/+51 dB; when VOUT and FDBK are shorted, the gain is lowered to 11 dB/+31 dB; when an external resistor is placed between VOUT and FDBK any intermediate gain can be achieved, for example, 1 dB/+41 dB. Figure 3 shows the nominal maximum gain versus external resistor for this mode.
Figure 3. Gain vs. REXT, Showing Worst-Case Limits Assuming Internal Resistors Have a Maximum Tolerance of 20%
REV. C
5
|
|
