Details, datasheet, quote on part number: AD9040AJN
PartAD9040AJN
CategoryData Conversion => ADC (Analog to Digital Converters) => <10 bit
DescriptionComplete 10-Bit Monolithic Sampling A/D Converter (ADC) With On-board Track-and-hold And Reference
CompanyAnalog Devices
DatasheetDownload AD9040AJN datasheet
Quote
Find where to buy
 
  

 

Features, Applications

FEATURES Low Power: 53 dB SNR @ 10 MHz AIN On-Chip T/H, Reference CMOS Compatible 2 V p-p Analog Input Fully Characterized Dynamic Performance APPLICATIONS Ultrasound Medical Imaging Digital Oscilloscopes Professional Video Digital Communications Advanced Television (MUSE Decoders) Instrumentation

The is a complete 10-bit monolithic sampling analogto-digital converter (ADC) with on-board track-and-hold and reference. The unit is designed for low cost, high performance applications and requires only an encode signal to achieve 40 MSPS sample rates with 10-bit resolution. Digital inputs and outputs are CMOS compatible; the analog input requires a signal 2 V p-p amplitude. The two-step architecture used in the AD9040A is optimized to provide the best dynamic performance available while maintaining low power requirements of only 940 mW typically; maximum dissipation is 1.1 watt at 40 MSPS. The signal-to-noise ratio (SNR), including harmonics, is 53 dB, or 8.5 ENOB, when sampling an analog input of 10.3 MHz at 40 MSPS. Competitive devices perform at less than 7.5 ENOB and require external references and larger input signals. The AD9040A A/D converter is available as either a 28-lead plastic DIP a 28-lead SOIC. The two models operate over a commercial temperature range to 70C. Contact the factory regarding availability of ceramic military temperature range devices.

1. CMOS-compatible logic for direct interface to ASICs. 2. On-board T/H provides excellent high frequency performance on analog inputs, critical for communications and medical imaging applications. 3. High input impedance and 2 V p-p input range reduce need for external amplifiers. 4. Easy to use; no cumbersome external voltage references required, allowing denser packing of ADCs for multichannel applications. 5. Available in 28-lead plastic DIP and SOIC packages. 6. Evaluation board includes AD9040AJR, reconstruction DAC, and latches. Space is available near the analog input and digital outputs of the converter for additional circuits. Order as part number AD9040A/PCB (schematic shown in data sheet).

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 Analog Devices, Inc., 2002

Parameter (Conditions) RESOLUTION DC ACCURACY Differential Nonlinearity Integral Nonlinearity No Missing Codes Gain Error Gain Tempco1 ANALOG INPUT Input Voltage Range Input Offset Voltage Input Bias Current Input Resistance Input Capacitance Analog Bandwidth BANDGAP REFERENCE Output Voltage Temperature Coefficient1 SWITCHING PERFORMANCE Maximum Conversion Rate Minimum Conversion Rate Aperture Delay (tA) Aperture Uncertainty (Jitter) Output Propagation Delay (tPD)2 DYNAMIC PERFORMANCE3 Transient Response Overvoltage Recovery Time Signal-to-Noise Ratio4 fIN = 2.3 MHz fIN = 10.3 MHz Signal-to-Noise Ratio4 (Without Harmonics) fIN = 2.3 MHz fIN = 10.3 MHz Signal-to-Noise Ratio4, 5 fIN = 2.3 MHz fIN = 10.3 MHz Signal-to-Noise Ratio4, 5 (Without Harmonics) fIN = 2.3 MHz fIN = 10.3 MHz 2nd Harmonic Distortion fIN = 2.3 MHz fIN = 10.3 MHz 3rd Harmonic Distortion fIN = 2.3 MHz fIN = 10.3 MHz Two-Tone Intermodulation6 Distortion Rejections Differential Phase Differential Gain 25C Full 25C Full 25C Full 25C Full 25C Full 25C Full 25C Full 51 50

Test Level Min AD9040AJN/JR Typ 10 1.0 Guaranteed Max Unit Bits LSB % FS ppm/C V p-p k pF MHz V ppm/C MSPS ns ps, rms ns dB

Parameter (Conditions) ENCODE INPUT Logic "1" Voltage Logic "0" Voltage Logic "1" Current Logic "0" Current Input Capacitance Encode Pulsewidth (High) (tEH)7 Encode Pulsewidth (Low) (tEL)7 DIGITAL OUTPUTS Logic "1" Voltage Logic "0" Voltage Output Coding POWER SUPPLY VD Supply Current +VS Supply Current VS Supply Current Power Dissipation Power Supply Rejection Ratio (PSRR)8 Temp Full 25C Full Test Level IV VI Min Offset Binary Full mA W mV/V 100 AD9040AJN/JR Typ Max Unit ns V

NOTES 1 "Gain Tempco" is for converter using internal reference; "Temperature Coefficient" is for bandgap reference only. 2 Output propagation delay (t PD) is measured from the 50% point of the falling edge of the encode command to the min/max voltage levels of the digital outputs with 10 pF maximum loads. 3 Minimum values apply to AD9040AJR only. 4 RMS signal to rms noise with analog input signal 1 dB below full scale at specified frequency. 5 ENCODE = 32 MSPS. 6 3rd order intermodulation measured with analog input frequencies of 2.3 MHz and 2.4 MHz 7 dB below full scale. 7 For rated performance at 40 MSPS, duty cycle of encode command should be Measured as the ratio of the change in offset voltage for a 5% change S or VS. Specifications subject to change without notice.

100% Production Tested. 100% production tested at 25C, and sample tested at specified temperatures. AC testing done on sample basis. III Sample Tested Only. IV Parameter is guaranteed by design and characterization testing. V Parameter is a typical value only. VI All devices are 100% production tested 25C. 100% production tested at temperature extremes for military temperature devices; guaranteed by design and characterization testing for industrial devices.

VS. 7 V VD. 7 V ANALOG INPUTS. VS to +VS DIGITAL INPUTS. V to +VS VREF Input. V to +VS Digital Output Current. 20 mA Operating Temperature to 70C Storage Temperature. to +150C Maximum Junction Temperature2 (JN/JR Suffixes). 150C Lead Soldering Temp (10 sec). 300C

NOTES 1 Absolute maximum ratings are limiting values to be applied individually, and beyond which the serviceability of the circuit may be impaired. Functional operability is not necessarily implied. Exposure to absolute maximum rating conditions for an extended period of time may affect device reliability. 2 Typical thermal impedances (parts soldered to board): N Package (Plastic DIP): 10C/W. R Package (SOIC): = 10C/W.

70C 28-Lead Plastic DIP 70C 28-Lead SOIC Package Printed Circuit Board (Only) of Evaluation Circuit Complete Evaluation Board, Assembled and Tested, Including AD9040AJR 3


 

Related products with the same datasheet
AD9040A
AD9040A/PCB
AD9040A/PWB
AD9040AJR
Some Part number from the same manufacture Analog Devices
AD9040AJR Complete 10-Bit Monolithic Sampling A/D Converter (ADC) With On-board Track-and-hold And Reference
AD9040APCB 10-bit 40 MSPS A/D Converter
AD9042 12-Bit, 41 MSPS Monolithic A/D Converter
AD9042D 12-bit, 41 MSPS Monolithic A/D Converter
AD9042D/PCB 12-Bit, 41 MSPS Monolithic A/D Converter
AD9042DPCB 12-bit, 41 MSPS Monolithic A/D Converter
AD9042ST/PCB 12-Bit, 41 MSPS Monolithic A/D Converter
AD9042STPCB 12-bit, 41 MSPS Monolithic A/D Converter
AD9048 Monolithic 8-Bit Video A/D Converter
AD9048SE Monolithic 8-bit Video A/D Converter
AD9048SE2 Monolithic 8-Bit Video A/D Converter
AD9048SQ Monolithic 8-bit Video A/D Converter
AD9048SQ2 Monolithic 8-Bit Video A/D Converter
AD9048TE Monolithic 8-bit Video A/D Converter
AD9048TE2 Monolithic 8-Bit Video A/D Converter
AD9048TQ Monolithic 8-bit Video A/D Converter
AD9048TQ2 Monolithic 8-Bit Video A/D Converter
AD9049 9-Bit, 30 MSPS ADC
AD9050 10-Bit, 40 MSPS/60 MSPS A/D Converter
AD9051 10-Bit, 60 MSPS A/D Converter
AD9051-2V 10-bit, 60 MSPS A/D Converter

ADG701L : The ADG701L/ADG702L are monolithic CMOS SPST switches. These switches are designed using an advanced submicron process that provides low power dissipation, yet offers high switching speed, low on resistance, and low leakage currents. In addition, −3 dB bandwidths of greater than 200 MHz can be

AD9522-5BCPZ-REEL7 : 12 LVDS/24 CMOS Output Clock Generator The AD9522-51 provides a multioutput clock distribution function with subpicosecond jitter performance, along with an on-chip PLL that can be used with an external VCO. The AD9522 serial interface supports both SPI and I2C ports. An in-package EEPROM ca

AME8800BEAT :

ADP1048ARQZ-R7 : Pmic - Pfc (power Factor Correction) Integrated Circuit (ics) Tape & Reel (TR) 30kHz ~ 400kHz 3 V ~ 3.6 V; IC DGTL PFC CTRLR 24QSOP Specifications: Packaging: Tape & Reel (TR) ; Package / Case: 24-SSOP (0.154", 3.90mm Width) ; Voltage - Supply: 3 V ~ 3.6 V ; Mode: Average Current ; Frequency - Switching: 30kHz ~ 400kHz ; Current - Startup: - ; Operating Temperature: -40C ~ 85C ; Lead Free Status: Lead Free ; RoHS Status: R

ADM6317DY30ARJ-RL7 : 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 Specifications: Package Type: SOT23, Other, MO-178AA, SOT-23, 5 PIN ; Operating Temperature: -40 to 85 C (-40 to 185 F)

ADM6318AX32ARJ-R7 : IC,POWER SUPPLY SUPERVISOR,TSOP,5PIN,PLASTIC

ADM6318LHARJ44DZ-RL : 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 Specifications: Package Type: SOT23, Other, MO-178AA, SOT-23, 5 PIN ; Operating Temperature: -40 to 85 C (-40 to 185 F)

ADM6320PARJ50CX-RL : 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 Specifications: Package Type: SOT23, Other, MO-178AA, SOT-23, 5 PIN ; Operating Temperature: -40 to 85 C (-40 to 185 F)

ADM6321AX46ARJZ-RL7 : IC,POWER SUPPLY SUPERVISOR,TSOP,5PIN,PLASTIC

 
0-C     D-L     M-R     S-Z