|
|
Part: EK01PC
Category:
Others
Description: Evaluation Kit For Sa01 Pin-out
Company: Apex Microtechnology Corporation
Datasheet: Download EK01PC datasheet File size : 74 kB
Request For quote: Find where to buy EK01PC
Datasheet text preview:
EVALUATION KIT FOR SA01 PIN-OUT
EK01
MICROTECHNOLOGY
HTTP://WWW.APEXMICROTECH.COM
(800) 546-APEX
(800) 546-2739
INTRODUCTION
This easy-to-use kit provides a platform for the evaluation of PWM amplifiers using the SA01 pin-out configuration. It can be used to analyze a multitude of standard or proprietary circuit configurations, and is flexible enough to do most standard amplifier test configurations. The board is designed for surface mounting all components except the switching amplifier. The schematic is shown in Figure 2. Note that all of the components shown on the schematic will probably not be used for any single circuit. Some components will simply be omitted, while others require installation of a jumper to complete the signal path. Only components unique to the EK01 are provided in this kit. Hardware similar to that shown in figure 1 must be obtained locally. The PC board and the foot print of the heatsink measure 3" by 5".
ASSEMBLY
1. From the non-silk screen side, insert and solder cage jacks. Be sure each one is fully seated. 2. From the non-silk screen side, push spacer grommets into PC board until fully seated. Grommets will snug when screws are inserted for heatsink mounting. 3. Apply TW10 thermal washer or a thin, even coat of thermal grease to the bottom of the SA01. If grease is from a tube make sure there is no sign separation of solids and liquids. If from a jar, stir it prior to application. 4. Use #14 sleeving to insulate and align at least 2 opposite pins of the amplifier. 5. Mount amplifier to heatsink using #6 screws and nuts. Do not over torque. 6. Install components as needed. External connections may be soldered directly or standard banana jacks may be soldered to these pads. 7. Insert amplifier pins into cage jacks and fasten board to heatsink.
PARTS LIST
Part # HS16 MS04 EK01PC 60SPG00001 TW10 Description Heatsink PC mount Cage Jacks PC Board Spacer Grommets Thermal Washer Quantity 1 1 Bag/12 each 1 4 1 Box/10 each
BEFORE YOU GET STARTED
* * * * * * * All Apex amplifiers should be handled using proper ESD precautions. Always use the heatsink included in this kit with thermal grease. Torque the part to the specified 8 to 10 in-lbs (.9 to 1.13 N*M) Always use adequate power supply bypassing. Do not change connections while the circuit is powered. Initially set all power supplies to the minimum operating levels allowed in the device data sheet. Check for oscillations.
Cage Jack PC Board (Silkscreen side) Solder as required
Spacer Grommet 6-32 x 1/2 Lg. Screw TW10 thermal washer or thermal grease as required
Heatsink #8 or #10 Screw (1/2" - 3/4" LG) Switching Amplifier Hex Nut 6-32 THD 1/4"
FIGURE 1.
APEX MICROTECHNOLOGY CORPORATION · TELEPHONE (520) 690-8600 · FAX (520) 888-3329 · ORDERS (520) 690-8601 · EMAIL prodlit@apexmicrotech.com
EK01
FIGURE 2. PCB SCHEMATIC.
TACH/ FEEDBACK C3 R7 C4 R11 R6 C6 EA OUT 3 7 +VS D4 7.5V REF +IN SA01 R3 R8 R9 R10 C8 +IN C13 R13 C2 C11 R15 D5 11V SHDN/ I SENSE FILTER 10 8 EA PWM B 9 OUT GND 4 A 6 OUT D1 D3 R2 R12 C10 C1 C7 R16
EVALUATION KIT FOR SA01 PIN-OUT
+VS
SIG R5 IN D6 11V REF OUT C9 D7 11V GND R14 R1
C5
1 5 2
C12
IN
AOUT
BOUT D2 GND
R4
R17
SHDN SIG
TYPICAL COMPONENT FUNCTIONS
R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12, 13, 15, 16 R14 R17 C1 C2 C3, 4 C5 C6 C7 C8 C9 C10, 11 C12 C13 D1 D4 D5 D7 Provides -IN bias from the Reference voltage. Sets DC scaling for external feedback such as tachometers, position sensors or current sensors. With R4 sets DC operating point of +IN, with R13 and R15 sets gain of voltage feedback circuit. With R3 sets DC operating point of +IN. Input scaling of the control signal. With C6 sets the corner frequency of the integrator. With C3 & C4 forms a low pass filter for the external feedback loop. Often used with tachometers. With C2 forms a low pass filter for the current limit circuit. Current sense. Often is a piece of resistance wire. With R8 divides shutdown signal voltage feeding SHDN/FILTER pin. With C5 sets corner frequency for external feedback loop. Provides voltage feedback for a voltage controlled output. Helps set gain or scale input voltage levels. With C12 provides low pass filtering of +IN signal. Power supply bypass. With R8 form a low pass filter for the current limit circuit, also filters the SHDN signal. With R7 forms a low pass filter for the external feed back loop. Often used with tachometers. With R11 sets corner frequency for external feedback loop. With R6 sets the corner frequency of the integrator. Power supply bypass, must have very low ESR in MHz range. Filters reference or feedback voltage at +IN. Bypass for the reference voltage. With R15 and R16 provides low pass filtering of voltage feedback. With R17 provides low pass filtering of +IN signal. Provides AC coupling of +IN signal. Optional flyback diodes. Input protection zener diodes.
APEX MICROTECHNOLOGY CORPORATION · 5980 NORTH SHANNON ROAD · TUCSON, ARIZONA 85741 · USA · APPLICATIONS HOTLINE: 1 (800) 546-2739
EVALUATION KIT FOR SA01 PIN-OUT
EK01
FIGURE 3. PCB FRONT.
OPEN LOOP OPERATION
R6 C6 +VS EA OUT 3 7 +VS A 6 OUT PWM B 9 OUT GND 4 R9 R10 C2 SHDN SIG BOUT C1 C7
1 5 REF OUT C9 R17 2
IN 7.5V REF +IN SA01
EA
AOUT
C12
SHDN/ I SENSE FILTER 10 8 R8
GND IN +2.5/+7.5
VIN Duty Cycle @ AOUT
2.5V 0% 5V 50% 7.5V 100%
(A B) =
VIN 5 V I R 2.5 * S O * DSON
APEX MICROTECHNOLOGY CORPORATION · TELEPHONE (520) 690-8600 · FAX (520) 888-3329 · ORDERS (520) 690-8601 · EMAIL prodlit@apexmicrotech.com
EK01
VOLTAGE CONTROL
SIG R5 1 R1 RO REF OUT C9 R17 SA01 5 2 IN 7.5V REF +IN SHDN/ I SENSE FILTER 10 8 R8 RI R10 C8 RF R13 C2 C11 R15 SHDN SIG R6 C6 EA OUT 3 7 +VS A 6 OUT PWM B 9 OUT GND 4 R9 BOUT C1 C7 R12 RF C10 R16 +VS
COMMON CONFIGURATIONS
EA
AOUT
(A B) = VIN *
RF RI
R4 RO
R3
GND
POSITION CONTROL
TACH/ FEEDBACK R7 R2 SIG R5 R11 R6 C5 1 R1 REF OUT C9 R17 5 2 IN 7.5V REF +IN SA01 R3 R8 R9 R10 C8 +IN C2 SHDN SIG SHDN/ I SENSE FILTER 10 8 C6 EA OUT 3 7 +VS A 6 OUT PWM B 9 OUT GND 4 AOUT +REF C1 C7 +VS
EA
M BOUT
REF
R4
GND
SPEED CONTROL
TACH/ FEEDBACK C3 R7 C4 R11 R6 C6 EA OUT 3 7 +VS A 6 OUT PWM B 9 OUT GND 4 R9 R10 C8 +IN C2 SHDN SIG AOUT M BOUT GND R8 T +VS C1 C7 R2
SIG R5
C5
1 R1 REF OUT C9 R17 5 2
IN 7.5V REF +IN SA01
EA
SHDN/ I SENSE FILTER 10 8
R4
R3
This data sheet has been carefully CORPORATION · to be NORTH SHANNON ROAD · assumed for possible inaccuracies or omissions. All specifications HOTLINE: change without notice. APEX MICROTECHNOLOGY checked and is believed 5980reliable, however, no responsibility isTUCSON, ARIZONA 85741 · USA · APPLICATIONS are subject to 1 (800) 546-2739 EK01U REV. C JANUARY 1998 © 1998 Apex Microtechnology Corp.
Others parts begin by ek
EK-1 EK-2 EK-3 EK-4 EK-5 EK-6
|
|
|
