|
|
Part: EK14
Category:
Others
Description: Evaluation Kit Sip03 Packaged op Amps
Company: Apex Microtechnology Corporation
Datasheet: Download EK14 datasheet File size : 74 kB
Request For quote: Find where to buy EK14
Datasheet text preview:
EVALUATION KIT SIP03 PACKAGED OP AMPS
EK14
MICROTECHNOLOGY
HTTP://WWW.APEXMICROTECH.COM
(800) 546-APEX
(800) 546-2739
INTRODUCTION
The EK14 evaluation kit provides a convenient way to breadboard circuits using Apex power op amps packaged in the 12-pin SIP03 package. The amplifier may be mounted vertically with the HS20 heat sink, or horizontally. Connections are provided for required power supply bypassing, external compensation components, as well as current limit resistors. A large area for component mounting provides flexibility and makes a multitude of circuit configurations possible.
PARTS LIST
Part # HS20 EVAL16 MS06 OX7R105KWN CSR10 TWO7 Description Heatsink PC Board Mating Socket 1µF Ceramic Capacitor .15 Resistor Thermal Washer Quantity 1 1 1 2 2 1 package
CAUTION ASSEMBLY
Use the supplied thermal washers or thermal grease between the power amplifier and the heat sink.
BEFORE YOU GET STARTED
· All Apex amplifiers should be handled using proper ESD precautions. · Always use the heat sink and thermal washers included in this kit. · Always use adequate power supply bypassing. · Do not change connections while the circuit is powered. · Initially set all power supplies to the minimum operating levels allowed in the device data sheet. · Check for oscillations.
1. On the silk screen side of the evaluation board, insert and solder the MS06 mating socket in DUT holes 1 12. Be sure each one is fully seated. 2. Solder components for your circuit. Be sure to include proper bypassing, required compensation components and current limit resistors. See the op amp data sheet for help in selecting these components. 1uF capacitors and a .15 resistor have been included with the EK12 kit but may be replaced with other components as necessary. 3. Place the TW07 thermal washer on the heat sink over the mounting hole for the DUT. Place a #6 screw through the mounting hole and thread a #6 nut onto the screw at the back of the heat sink. Do not tighten. Note that there are two sets of mounting holes on the HS20. Holes on one edge allow room between the DUT and evaluation board for the MS06 socket. The holes on the other edge are for direct through hole mounting of the DUT to the evaluation board. It is recommended that you use the MS06. 4. Mount the DUT to the HS20 by sliding under the head of the #6 screw and on top of the thermal washer. Tighten the nut to the specified 8 to 10 in-lbs. (.9 to .13 N*M). Do not over torque. 5. Install leads of the DUT into the MS06 on the evaluation board. Use #6 self-tapping screws to secure the evaluation board to the HS20 heat sink as shown in the assembly diagram (Figure 1).
APEX MICROTECHNOLOGY CORPORATION · TELEPHONE (520) 690-8600 · FAX (520) 888-3329 · ORDERS (520) 690-8601 · EMAIL prodlit@apexmicrotech.com
EK14
EVALUATION KIT FOR SIP03 PIN-OUT
FIGURE 1.
This data sheet has been carefully APEX MICROTECHNOLOGY checked and is believed to be reliable, however, no responsibility· TUCSON, ARIZONA 85741 or omissions. All specifications are subject to change without notice. CORPORATION · 5980 NORTH SHANNON ROAD is assumed for possible inaccuracies · USA · APPLICATIONS HOTLINE: 1 (800) 546-2739 EK14 REV. A DECEMBER 1998 © 1998 Apex Microtechnology Corp.
Others parts begin by ek
EK-1 EK-2 EK-3 EK-4 EK-5 EK-6
|
|
|
