Details, datasheet, quote on part number: AT87F51-24PI
PartAT87F51-24PI
CategoryMicrocontrollers => 8 bit
Description8-bit Microcontroller With4k Bytes Quickflash
CompanyATMEL Corporation
DatasheetDownload AT87F51-24PI datasheet
Quote
Find where to buy
 
  

 

Features, Applications
Features

Compatible with MCS-51TM Products 4K Bytes of User Programmable QuickFlashTM Memory Fully Static Operation: to 24 MHz Three-Level Program Memory Lock x 8-Bit Internal RAM 32 Programmable I/O Lines Two 16-Bit Timer/Counters Six Interrupt Sources Programmable Serial Channel Low Power Idle and Power Down Modes

Description

The is a low-power, high-performance CMOS 8-bit microcomputer with 4K bytes of QuickFlash Programmable Read Only Memory. The device is manufactured using Atmel's high density nonvolatile memory technology and is compatible with the industry standard MCS-51TM instruction set and pinout. The on-chip QuickFlash allows the program memory to be user programmed by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with QuickFlash on a monolithic chip, the Atmel is a powerful microcomputer which provides a highly flexible and cost effective solution to many embedded control applications.


PSEN ALE/PROG EA / VPP RST PORT 1 LATCH PORT 3 LATCH TIMING AND CONTROL INSTRUCTION REGISTER DPTR

The AT87F51 provides the following standard features: 4K bytes of QuickFlash, 128 bytes of RAM, 32 I/O lines, two 16-bit timer/counters, a five vector two-level interrupt architecture, a full duplex serial port, on-chip oscillator and clock circuitry. In addition, the AT87F51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power Down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset. when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX @ RI), Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the high-order address bits and some control signals during QuickFlash programming and verification. Port 3 Port an 8-bit bidirectional I/O port with internal pullups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pullups. Port 3 also serves the functions of various special features of the AT87F51 as listed below:

Port Pin P3.6 P3.7 Alternate Functions RXD (serial input port) TXD (serial output port) INT0 (external interrupt 0) INT1 (external interrupt 1) T0 (timer 0 external input) T1 (timer 1 external input) WR (external data memory write strobe) RD (external data memory read strobe)

VCC Supply voltage. GND Ground. Port 0 Port an 8-bit open drain bidirectional I/O port. As an output port each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as highimpedance inputs. Port 0 may also be configured to be the multiplexed loworder address/data bus during accesses to external program and data memory. In this mode P0 has internal pullups. Port 0 also receives the code bytes during QuickFlash programming, and outputs the code bytes during program verification. External pullups are required during program verification. Port 1 Port an 8-bit bidirectional I/O port with internal pullups. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 1 also receives the low-order address bytes during QuickFlash programming and verification. Port 2 Port an 8-bit bidirectional I/O port with internal pullups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @ DPTR). In this application it uses strong internal pullups

Port 3 also receives some control signals for QuickFlash programming and verification. RST Reset input. A high on this pin for two machine cycles while the oscillator is running resets the device. ALE/PROG Address Latch Enable output pulse for latching the low byte of the address during accesses to external memory. This pin is also the program pulse input (PROG) during QuickFlash programming. In normal operation ALE is emitted at a constant rate of 1/6 the oscillator frequency, and may be used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped during each access to external Data Memory. If desired, ALE operation can be disabled by setting bit 0 of SFR location 8EH. With the bit set, ALE is active only during a MOVX or MOVC instruction. Otherwise, the pin is weakly pulled high. Setting the ALE-disable bit has no effect if the microcontroller is in external execution mode. PSEN Program Store Enable is the read strobe to external program memory.


 

Related products with the same datasheet
AT87F51-12AI
AT87F51-12JC
AT87F51-12JI44J
AT87F51-12PC
AT87F51-12PI
AT87F51-16AC
AT87F51-16AI
AT87F51-16JC
AT87F51-16JI
AT87F51-16PC
AT87F51-16PI
AT87F51-20AC
Some Part number from the same manufacture ATMEL Corporation
AT87F51-33 8-bit Microcontroller With 4k Bytes Quickflash (tm)
AT87F51RC 8-bit Microcontroller With 32k Bytes Quickflash(tm)
AT87F52 8-bit Microcontroller With 8k Bytes Quickflash (tm)
AT87F55 8-bit Microcontroller With 20k Bytes Quickflash(tm)
AT87F55WD 80C32 Microcontroller With 20K OTP Quickflash
AT87LV51-16AC
AT87LV51-16AI
AT87LV51-16JC
AT87LV51-16JI
AT87LV51-16PC
AT87LV51-16PI
AT87LV52 8-bit Microcontroller With 8k Bytes Quickflash (tm)
AT87LV55-12AC
AT87LV55-12AI

5962-9154504MXX : High-density Uv-erasable Programmable Logic Device

AT28C256-25C : 256k (32k X 8) Paged CMOS E2PROM

AT80F52-12AC : CISC->8051/80C51 Family->EEPROM/Flash 8-bit Microcontroller With 8k Bytes Quickflash Memory

AT93C66-10C-2.7 : 1k (128x8 or 64x16),2k (256x8 or 128x16),4k (512x8 or 256x16) 3-wire Serial EePROMs

U6032B : Toggle ic For Switch-over Function

AT24C256BW-SH-B : Two-wire Serial Eeprom Smart Card Modules 128K (16,384 x 8) 256 (32,768 x 8)

AT27C256R-25RI : 32K X 8 OTPROM, 120 ns, PQCC32 Specifications: Memory Category: PROM ; Density: 262 kbits ; Number of Words: 32 k ; Bits per Word: 8 bits ; Package Type: PLASTIC, MS-016AE, LCC-32 ; Pins: 32 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 120 ns ; Operating Temperature: -40 to 125 C (-40 to 257 F)

ATF22V10C-5SC : FLASH PLD, 10 ns, CDIP24 Specifications: Package Type: Other, DIP-24 ; Pins: 24 ; Logic Family: CMOS ; Internal Frequency: 90 MHz ; User I/Os: 10 pins ; Propagation Delay: 10 ns ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Supply Voltage: 5V

ATMEGA128L-8AN : 8-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP64 Specifications: Data Bus: 8 Bit ; Life Cycle Stage: ACTIVE ; Clock Speed: 8 MHz ; ROM Type: Flash ; Supply Voltage: 2.7 to 5.5 volts ; I/O Ports: 53 ; Package Type: TQFP, Other, 14 X 14 MM, 1 MM HEIGHT, 0.80 MM PITCH, PLASTIC, MS-026AEB, TQFP-64 ; Operating Range: Industrial ; Pin Count: 64 ; Operat

TT28C010N-25M-5 : IC,EEPROM,128KX8,CMOS,FP,32PIN,CERAMIC Specifications: Memory Category: PROM

 
0-C     D-L     M-R     S-Z