Details, datasheet, quote on part number: ATF22V10CQ-15PC
CategoryFPGAs/PLDs => PLDs (Programmable Logic Devices) => SPLDs (Simple PLD) => EE Programmable SPLD
TitleEE Programmable SPLD
DescriptionHigh-performance Eepld
CompanyATMEL Corporation
DatasheetDownload ATF22V10CQ-15PC datasheet
Cross ref.Similar parts: PAL16L8A, PAL16L8A-2, PAL16L8AM, PAL16R4A, PAL16R4A-2M, PAL16R4AM, PAL16R6A, PAL16R6AM, PAL16R8A, PAL16R8AM
Find where to buy


Features, Applications
High-speed, Electrically Erasable Programmable Logic Devices
Latch Feature Holds Inputs to Previous Logic States
Pin-controlled Standby Power (10 A Typical) Advanced Flash Technology

Reprogrammable 100% Tested High-reliability CMOS Process 20-year Data Retention 100 Erase/Write Cycles 2,000V ESD Protection 200 mA Latch-up Immunity Dual Inline and Surface Mount Packages in Standard Pinouts PCI-compliant True Input Transition Detection "Z" and "QZ" Version

Pin Name CLK IN I/O GND VCC PD Function Clock Logic Inputs Bi-directional Buffers Ground +5V Supply Power-down PLCC

For all PLCCs (except "-5"), pins 8, 15 and 22 can be left unconnected. However, if they are connected, superior performance will be achieved.


The is a high-performance CMOS (electrically erasable) programmable logic device (PLD) that utilizes Atmel's proven electrically erasable Flash memory technology. Speeds down 5 ns and power dissipation as low 100 A are offered. All speed ranges are specified over the full 10% range for industrial temperature ranges, and 5% for commercial temperature ranges. Several low-power options allow selection of the best solution for various types of power-limited applications. Each of these options significantly reduces total system power and enhances system reliability.

Temperature under Bias.................................. to +85C Storage Temperature..................................... to +150C Voltage on Any Pin with Respect to +7.0V(1) Voltage on Input Pins with Respect to Ground during to +14.0V(1) Note: Programming Voltage with Respect +14.0V(1) 1. *NOTICE: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Minimum voltage is -0.6V DC, which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V DC, which may overshoot to 7.0V for pulses of less than 20 ns.

Commercial Operating Temperature (Ambient) VCC Power Supply 5% Industrial 10%

PAL Mode (5828 Fuses) Synario WINCUPL Note: ATF22V10C (DIP) ATF22V10C (PLCC) P22V10 P22V10LCC GAL Mode (5892 Fuses) ATTF22V10C DIP (UES) ATF22C10C PLCC (UES) G22V10 G22V10LCC Power-down Mode(1) (5893 Fuses) ATF22V10C DIP (PWD) ATF22V10C PLCC (PWD) G22V10CP G22V10CPLCC

1. These device types will create a JEDEC file which when programmed in ATF22V10C devices will enable the power-down mode feature. All other device types have the feature disabled.

Symbol IIL IIH Parameter Input or I/O Low Leakage Current Input or I/O High Leakage Current Condition 0 VIN VIL (Max) 3.5 VIN VCC 10 C-10 ICC Power Supply Current, Standby VCC = Max, VIN = Max, Outputs Open C-10 ICC2 Clocked Power Supply Current VCC = Max, Outputs Open, = 15 MHz C-15 CQ-15 IPD IOS(1) VIL VIH VOL Power Supply Current, PD Mode Output Short Circuit Current Input Low Voltage Input High Voltage VIN = VIH or VIL, VCC = Min VIN = VIH or VIL, VCC = Min IOL 16 mA IOL 12 mA IOH -4.0 mA Com., Ind. Mil. 2.4 VCC = Max VIN = 0, Max VOUT -0.5 2.0 Com. Ind. Com. Ind. Com. Ind. Com. Ind. Com. Ind. Com. Ind. Com. Ind. Min Typ -35.0 Max VCC+0.75 0.5 Units A mA

1. Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec.


Related products with the same datasheet
Some Part number from the same manufacture ATMEL Corporation
ATF22V10CQ-15PI High-performance Eepld
ATF2500C High-speed Programmable Logic Device
ATF750C High-speed Complex Programmable Logic Device
ATFS05 Configuration Memory Used to Load The Bitstream For AT94K05AL Fpslic Devices.
ATFV2500C High Speed Programmable Logic Device
ATL25 The ATL25 Series Gate Array And Embedded Array Families From Atmel Are Fabricated on a 0.25 Micron CMOS Process With 5 Levels of Metal. This Family Features Arrays With up to 6.9 Million Routable Gates

AT27LV020A-12TC : ->UV/EPROM 2-mb (256kx8) Low Voltage OTP EPROM

AT45D011-JI : 1-mb 5.0-volt Only Serial Dataflash(r)

AT49BV002AT-70JC : 256K X 8 (2M Bit), 2.7-Volt Read And 2.7-Volt Write, Bottom Boot Parametric Block Flash

MH1242 : Military/Aerospace 1.6M Used Gates 0.35 m CMOS Sea of Gates / Embedded Arrays

AT24C32_03 : 2-wire Serial Eeprom

AT90PWM1-16MUR : 8-bit Microcontroller with 8K Bytes In-system Programmable Flash

AT91SAM7XC128-CU-999 : AT91 ARM Thumb-based Microcontrollers Atmel's AT91SAM7XC256/128 is a member of a series of highly integrated Flash microcontrollers based on the 32-bit ARM RISC processor. It features 256/128 Kbyte high-speed Flash and 64/32 Kbyte SRAM, a large set of peripherals, including an 802.3 Ethernet MA

MMDP-67206EV-30 : 4K X 9 OTHER FIFO, 40 ns, CDFP28 Specifications: Memory Category: FIFO ; Density: 37 kbits ; Number of Words: 4 k ; Bits per Word: 9 bits ; Package Type: 0.400 INCH, FP-28 ; Pins: 28 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 40 ns ; Cycle Time: 50 ns ; Operating Temperature: -55 to 125 C (-67 to 257 F)

T89C5121-S3RIL : 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP44 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 16 MHz ; ROM Type: Flash ; Supply Voltage: 2.85 to 5.4 volts ; Package Type: Other, VQFP-44 ; Operating Range: Industrial ; Pin Count: 44 ; Operating Temperature: -40 to 85 C (-40 to 185 F)

0-C     D-L     M-R     S-Z