|
Details, datasheet, quote on part number:W208D
| |
| Part: | W208D |
| Category: | Timing Circuits => Clock Generators => General Purpose PLL |
| Description: | FTG For Integrated Core Logic With 133-MHz FSB |
| Company: | Cypress Semiconductor Corp. |
| Datasheet: | Download W208D datasheet File size : 173 kB |
| Request For quote: | Find where to buy W208D
|
| |
Datasheet text preview:
PRELIMINARY
W208 D
FTG for Integrated Core Logic with 133-MHz FSB
Features
· Maximized EMI suppression using Cypress's Spread Spectrum technology · Low jitter and tightly controlled clock skew · Highly integrated device providing clocks required for CPU, core logic, and SDRAM · Three copies of CPU clock at 66/100 MHz · Nine copies of 100-MHz SDRAM clocks · Eight copies of PCI clock · Two copies of synchronous APIC clock · Two copies of 48-MHz clock (non-spread spectrum) optimized for USB reference input and video dot clock · Two copies of 66-MHz fixed clock · One copy of 14.31818-MHz reference clock · Power down control · I2CTM interface for turning off unused clocks APIC, 48-MHz, SDRAM Output Skew: ...... 250 ps CPU, 3V66 Output Skew:...........175 ps PCI Output Skew:........500 ps CPU to SDRAM Skew (@ 133 MHz):.......±0.5 ns CPU to SDRAM Skew (@ 100 MHz):........4.5 to 5.5 ns CPU to 3V66 Skew (@ 66 MHz): ..... 7.0 to 8.0 ns 3V66 to PCI Skew (3V66 lead):..1.5 to 3.5 ns PCI to APIC Skew: ..... ±0.5 ns Table 1. Pin Selectable Functions SEL133 X X 0 0 1 1 SEL1 0 0 1 1 1 1 SEL0 0 1 0 1 0 1 Function Three-state Test 66-MHz CPU 100-MHz CPU Reserved 133-MHz CPU
Key Specifications
CPU, SDRAM Outputs Cycle-to-Cycle Jitter:..... 250 ps APIC, 48-MHz, 3V66, PCI Outputs Cycle-to-Cycle Jitter:......... 500 ps
Block Diagram
VDDQ3
Pin Configuration [1]
REF/SEL133* VDDQ3 X1 X2 GND GND 3V66_0 3V66_1 VDDQ3 VDDQ3 PCI0_ICH PCI1 PCI2 GND PCI3 PCI4 GND PCI5 PCI6 PCI7 VDDQ3 VDDQ3 GND GND USB DOT VDDQ3 SEL0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 GND APIC0 APIC1 VDDQ2 CPU0 VDDQ2 CPU1 CPU2_ITP GND GND SDRAM0 SDRAM1 VDDQ3 SDRAM2 SDRAM3 GND SDRAM4 SDRAM5 VDDQ3 SDRAM6 SDRAM7 GND DCLK VDDQ3 PWRDWN# SCLK SDATA SEL1
X1 X2
XTAL OSC
PLL REF FREQ
REF/SEL133
VDDQ2
SDATA SCLK
I2C Logic
Divider, Delay, and Phase Control Logic
2
CPU0:1 CPU2_ITP APIC0:1 VDDQ3
W208D
2
SEL0:1
PLL 1
2
3V66_0:1
PCI0_ICH PCI1:7
7
DCLK PWRDWN#
8
SDRAM0:7
PLL2
VDDQ3 USB DOT
Note: 1. Internal pull-down resistors present on input marked with *. Design should not solely rely on internal pull-down resister to set I/O pin LOW.
I2C is a trademark of Phillips Corporation. Intel is a registered trademark of Intel Corporation.
Cypress Semiconductor Corporation Document #: 38-07228 Rev. **
·
3901 North First Street
·
San Jose
·
CA 95134 · 408-943-2600 Revised September 27, 2001
PRELIMINARY
Pin Definitions
Pin Name REF/SEL133 Pin No. 1 Pin Type I/O Pin Description
W208D
Reference Clock/Select 133-MHz FSB: 3.3V 14.318-MHz clock output. This pin also serves as a strap option for CPU frequency selection. See Table 1 for detailed descriptions. Crystal Input: This pin has dual functions. It can be used as an external 14.318-MHz crystal connection or as an external reference frequency input. Crystal Output: An input connection for an external 14.318-MHz crystal. If using an external reference, this pin must be left unconnected. PCI Clock 0 through 7: 3.3V 33-MHz PCI clock outputs. PCI1:7 can be individually turned off via I2C interface. 66-MHz Clock Output: 3.3V fixed 66-MHz clock. USB Clock Output: 3.3V fixed 48-MHz, non-spread spectrum USB clock outputs. Dot Clock Output: 3.3V 48-MHz, non-spread spectrum signal. Clock Function Selection Pins: LVTTL-compatible input to select device functions. See Table 1 for detailed descriptions. Power-Down Control: LVTTL-compatible asynchronous input that places the device in power-down mode when held LOW. CPU Clock Outputs: Clock outputs for the host bus interface and integrated test port. Output frequencies run at 66 MHz, 100 MHz, or 133 MHz, depending on the configuration of SEL0:1 and SEL133. Voltage swing set by VDDQ2. SDRAM Clock Outputs: 3.3V outputs running at 100 MHz. SDRAM0:7 can be individually turned off via I2C interface. Synchronous APIC Clock Outputs: Clock outputs running synchronous with the PCI clock outputs (33 MHz). Voltage swing set by VDDQ2. Data pin for I2C circuitry. Clock pin for I2C circuitry. 3.3V Power Connection: Power supply for SDRAM output buffers, PCI output buffers, 3V66 output buffers, reference output buffers, and 48-MHz output buffers. Connect to 3.3V. 2.5V Power Connection: Power supply for IOAPIC and CPU output buffers. Connect to 2.5V or 3.3V. Ground Connections: Connect all ground pins to the common system ground plane.
X1 X2 PCI0_ICH, PCI1:7 3V66_0:1 USB DOT SEL0:1 PWRDWN# CPU2_ITP, CPU0:1 SDRAM0:7, DCLK APIC0:1 SDATA SCLK VDDQ3
3 4 11, 12, 13, 15, 16, 18, 19. 20 7, 8 25 26 28, 29 32 49, 52, 50
I I O O O O I I O
46, 45, 43, 42, 40, 39, 37, 36, 34 55, 54 30 31 2, 9, 10, 21, 22, 27, 33, 38, 44 51, 53 5, 6, 14, 17, 23, 24, 35, 41, 47, 48, 56
O
O I/O I P
VDDQ2 GND
P G
Document #: 38-07228 Rev. **
Page 2 of 14
PRELIMINARY
VDD Output Strapping Resistor 10 k (Load Option 1) W208D Power-on Reset Timer Output Buffer Output Three-state
Q
W208D
Series Termination Resistor Clock Load
Hold Output Low
D
10k (Load Option 0)
Data Latch
Figure 1. Input Logic Selection Through Resistor Load Option
Overview
The W208D is a highly integrated frequency timing generator, supplying all the required clock sources for an Intel® architecture platform using graphics integrated core logic.
Functional Description
I/O Pin Operation REF/SEL133 is a dual-purpose l/O pin. Upon power-up the pin acts as a logic input. If the pin is strapped to a HIGH state externally, CPU clock outputs will run at 133 MHz. If it is strapped LOW, CPU clock outputs will be determined by the status of SEL0:1 input pins. An external 10-k strapping resistor should be used. Figure 1 shows a suggested method for strapping resistor connections. Table 2. CK Whitney Truth Table SEL133 X X 0 0 1 1 SEL1 0 0 1 1 1 1 SEL0 0 1 0 1 0 1 133 MHz 100 MHz 66 MHz CPU Hi-Z TCLK/4 66 MHz 100 MHz SDRAM Hi-Z TCLK/4 100 MHz 100 MHz 3V66 Hi-Z TCLK/6 66 MHz 66 MHz
After 2 ms, the pin becomes an output. Assuming the power supply has stabilized by then, the specified output frequency is delivered on the pins. If the power supply has not yet reached full value, output frequency initially may be below target but will increase to target once supply voltage has stabilized. In either case, a short output clock cycle may be produced from the CPU clock outputs when the outputs are enabled. Pin Selectable Functions Table 1 outlines the device functions selectable through SEL133 and SEL0:1. Specific outputs available at each pin are detailed in Table 2 below. The SEL0 pin requires a 220 pull-up resistor to 3.3V for the W208D to sense the maximum host bus frequency of the processor and configure itself accordingly.
PCI Hi-Z TCLK/12 33 MHz 33 MHz 33 MHz
48MHz Hi-Z TCLK/2 48 MHz 48 MHz 48 MHz
REF Hi-Z TCLK 14.318 MHz 14.318 MHz 14.318 MHz
APIC Hi-Z TCLK/12 33 MHz 33 MHz 33 MHz
Notes 2 4, 5 3, 6, 7 3, 6, 7 3, 6, 7
Reserved
Notes: 2. Provided for board-level "bed of nails" testing. 3. "Normal" mode of operation. 4. TCLK is a test clock overdriven on the XTAL_IN input during test mode. 5. Required for DC output impedance verification. 6. Range of reference frequency allowed is min. = 14.316 MHz, nominal = 14.31818 MHz, max. = 14.32 MHz. 7. Frequency accuracy of 48 MHz must be +167 PPM to match USB default.
Document #: 38-07228 Rev. **
Page 3 of 14
|
|
