|
Details, datasheet, quote on part number:DB1501PT
| |
Datasheet text preview:
DIOTEC ELECTRONICS CORP.
18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958
D a t a Sheet No. BRDB-1500P-1C ADBD-1500P-1C
FEATURES
MECHANICAL SPECIFICATION
SERIES: DB1500P - DB1510P and ADB1504P - ADB1508P
Suffix "P" indicates molded PLASTIC with integrally mounted Heat Sink Heat Sink
VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) BUILT-IN STRESS RELIEF MECHANISM FOR S U P E R I O R R E L I A B I L I T Y AND P E R F O R M A N C E INTEGRALLY MOLDED HEAT SINK PROVIDES VERY LOW THERMAL RESISTANCE FOR MAXIMUM HEAT DISSIPATION
BH
BH
Molded Body
LT
LL
Molded Body
D1
HOLE FOR #8 SCREW
Top View of Heat Sink
HOLE F O R #8 SCREW
LD
UL RECOGNIZED - FILE #E141956
+
AC
AC
AC
+
AC
MECHANICAL DATA
Case: Molded plastic, U/L Flammability Rating 94V-0 Terminals: Round silver plated copper pins or fast-on terminals Soldering: Per MIL-STD 202 Method 208 guaranteed (Note 1) Polarity: Marked on side of case Mounting Position: Any. Through hole for #8 screw. Max. mounting torque = 20 in-lb. Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams) Wire Leads - 0.55 Ounce (16.0 Grams)
D1
AC
D3
BL
AC
BL D1
_
D2 BL
+ _
_
D2
D1 BL
Suffix "T" indicates FAST-ON TERMINALS
Suffix "W" indicates WIRE LEADS
MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS
Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.
PARAMETER (TEST CONDITIONS)
Series Number Maximum DC Blocking Voltage Working Peak Reverse Voltage Maximum Peak Recurrent Reverse Voltage RMS Reverse Voltage Rating for Fusing (Non Repetitive; 1mS < t < 8.3mS) Peak Forward Surge Current. Single 60Hz Half-Sine Wave Superimposed on Rated Load (JEDEC Method). TJ = 150O C Average Forward Rectified Current @ TC = 50 C
Junction Operating and Storage Temperature Range Mimimum Avalanche Voltage Maximum Avalanche Voltage Maximum Forward Voltage (Per Diode) at 7.5 Amps DC
o
RATINGS
SYMBOL
CONTROLLED AVALANCHE
NON-CONTROLLED AVALANCHE
UNITS
ADB ADB ADB DB DB DB DB DB DB DB 1504P 1506P 1508P 1500P 1501P 1502P 1504P 1506P 1508P 1510P
VRM VRWM VRRM VR (RMS) It IFSM IO TJ, TSTG V(BR) Min V(BR) Max VFM IRM VISO RJC
See N o t e 1 See N o t e 1 1.05 1 50 2500 1.4
2
400
600
800
50
100
200
400
600
800 1 0 0 0
VOLTS
280 420 560 35 70 140 375 300 15 -55 to +150 n/a n/a 280 420 560 700
AMPS2 SEC AMPS °C
VOLTS
@ TA = 25o C Maximum Reverse Current at Rated VRM @TA = 125o C Minimum Insulation Breakdown Voltage (Circuit to Case) Typical Thermal Resistance, Junction to Case
µA VOLTS
o
C/W
3.01 1 5 d b p
NOTES: (1) These bridges exhibit the avalanche characteristic at breakdown. If your application requires a specific breakdown voltage range, please contact us.
E37
DIOTEC ELECTRONICS CORP.
18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958
Data S h e e t N o . B R D B - 1 5 0 0 P - 2 B ABDB-1500P-2B
15 AMP SILICON BRIDGE RECTIFIERS
RATING & CHARACTERISTIC CURVES FOR SERIES DB1500P - DB1510P and SERIES ADB1504P - ADB1508P
60Hz Resistive and Inductive Loads
400
TJ = 150o C
300
200
Bridge Mounted on 5 x 4 x 3" Thick (12.7 x 10.2 x 7.6cm) Finned Al. Plate
100
60
1
10
100
Case Temperature, C FIGURE 1. FORWARD CURRENT DERATING CURVE
o
Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
1000
10
100
TJ = 125O C
1.0
10
1.0
TJ = 25o C Pulse Width = 300µSec 1%Duty Cycle
0.1
TJ = 25O C
0.1
.01 0 20 40 60 80 100 120 140
Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE
Percent of Rated Peak Reverse Voltage FIGURE 4. TYPICAL REVERSE CHARACTERISTICS
E38
3.01 1 5 d b p
|
|
