|
Details, datasheet, quote on part number:RS605
| |
Datasheet text preview:
DIOTEC ELECTRONICS CORP.
18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958
Data S h e e t N o . B S B U - 6 0 0 - 1 C
FEATURES
MECHANICAL SPECIFICATION
SBU PACKAGE SHOWN ACTUAL SIZE C C1 C2 D D3 _ D2 + D D1 A
VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) BUILT-IN STRESS RELIEF MECHANISM FOR S U P E R I O R R E L I A B I L I T Y AND P E R F O R M A N C E SURGE OVERLOAD RATING TO 250 AMPS PEAK IDEAL FOR PRINTED CIRCUIT BOARD APPLICATIONS THRU-HOLE FOR EASY HEAT SINK MOUNTING
A1 L
UL RECOGNIZED - FILE #E124962
MECHANICAL DATA
L1 B1 B Case: Molded plastic, U/L Flammability Rating 94V-0
SYM A MILLIMETERS MIN 6.6 4.7 1.22 4.57 22.7 4.2 3.6 n/a 10.3 1.7 16.5 25.4 4.57 MAX 7.1 5.2 1.32 5.59 23.24 4.7 4.1 19.3 11.3 2.2 17.8 n/a 6.8 INCHES MIN 0.260 0.185 0.048 0.180 0.895 0.165 0.140 n/a 0.405 0.065 0.660 1.0 0.180 MAX 0.280 0.205 0.052 0.220 0.915 0.185 0.160 0.760 0.455 0.085 0.700 n/a 0.260
Terminals: Round silver plated pins
A1 B B1 C C1 C2 D D1 D2 D3 L L1
Soldering: Per MIL-STD 202 Method 208 guaranteed
_
+
Polarity: Marked on case
Mounting Position: Any. Max. mounting torque = 5 in lb
SERIES SBU6A - SBU6M
Weight: 0.3 Ounces (8 Grams)
MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS
Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.
PARAMETER (TEST CONDITIONS)
Series Number Maximum DC Blocking Voltage Maximum RMS Voltage Maximum Peak Recurrent Reverse Voltage Average Forward Rectified Current TC = 100o C (Notes 1, 3) TA = 40o C (Note 2) Peak Forward Surge Current. Single 60Hz Half-Sine Wave Superimposed on Rated Load (JEDEC Method). TJ = 150O C Maximum Forward Voltage (Per Diode) at 6 Amps DC @ TA = 25o C Maximum Average DC Reverse Current At Rated DC Blocking Voltage @ TA = 100o C Junction to Ambient (Note 2) Typical Thermal Resistance Junction to Case (Note 3) Operating and Storage Temperature Range
SYMBOL
SBU 6A VRM VRMS VRRM IO IFSM VFM IRM RJA RJC TJ ,TSTG 50 35 50 SBU 6B 100 70 100
RATINGS
SBU 6D 200 140 200 SBU 6G 400 280 400 6 6 250 0.95 (Typical < 0.90) 1 50 16.0 3.1 -55 to +150 SBU 6J 600 420 600 SBU 6K 800 560 800 SBU 6M 1000 700 1000
UNITS
VOLTS
AMPS
VOLTS µA °C/W °C
3 . 0 1 06sbu
NOTES: (1) Bridge mounted on 2.6" x 1.4" x 0.06" thick (6.5cm x 3.5cm x 0.15cm) aluminum plate (2) Bridge mounted on PC Board with 0.5" sq. (12mm sq.) copper pads and bridge lead length of 0.375" (9.5mm) (3) Bolt bridge on heat sink with #6 screw, using silicon thermal compound between bridge and mounting surface for maximum heat transfer.
E23
DIOTEC ELECTRONICS CORP.
18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958
Data S h e e t N o . B S B U - 6 0 0 - 2 B
6 AMP SILICON BRIDGE RECTIFIERS
RATING & CHARACTERISTIC CURVES FOR SERIES SBU6A - SBU6M
250
NOTE 1 60Hz Resistive or Inductive Loads
200
150
Case, TC Ambient, TA
100
50
NOTE 2 Temperature, oC FIGURE 1. FORWARD CURRENT DERATING CURVE
0 1 10 100
Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
100
50
10
10
TJ = 100 oC
1.0
NOTE 3
1.0
0.1
TJ = 2 5 C
0.1
0.01 0 20 40 60 80 100 120 140
o
Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE
400 Note 4
Percent of Rated Peak Reverse Voltage FIGURE 4. TYPICAL REVERSE CHARACTERISTICS
NOTES (1) Case Temperature, TC, With Bridge Mounted on 2.6" x 1.4" x 0.06" Thick (6.5cm x 3.5cm x 0.15cm) Aluminum Plate Ambient Temperature, TA, With Bridge Mounted on PC Board With 0.5" Sq. (12mm Sq.) Pads and Bridge Lead Length of 0.375" (9.5mm) (2) TJ = 150o C
100
10 1 10 100
Reverse Voltage, (Volts) FIGURE 5. TYPICAL JUNCTION CAPACITANCE PER DIODE
(3) TJ = 25o C; Pulse Width = 300µSec; 1% Duty Cycle (4) TJ = 25o C; f = 1 MHz; Vsig = 50mVp-p
E24
3 . 0 1 06sbu
|
|
