Details, datasheet, quote on part number: A6130DL8A
Description5V Accurate Regulator With Integrated Windowed Watchdog.
CompanyEM Microelectronic
DatasheetDownload A6130DL8A datasheet
Find where to buy


Features, Applications

High Efficiency Linear Power Supply with Accurate Power Surveillance and Software Monitoring

Highly accurate 100 mA guaranteed output Low dropout voltage, typically 100 mA Low quiescent current, typically 155 A Standby mode, maximum current 340 A (with 100 A load on OUTPUT) Unregulated DC input can withstand -20 V reverse battery and +60 V power transients Fully operational for unregulated DC input voltage 26 V and regulated output voltage down 3.0 V Reset output guaranteed for regulated output voltage down V No reverse output current Very low temperature coefficient for the regulated output Current limiting Comparator for voltage monitoring, voltage reference 1.17V 2.2% voltage reference accuracy +25C 4.2% voltage reference accuracy from to +85C Programmable reset voltage monitoring Programmable power on reset (POR) delay Watchdog with programmable time windows guarantees a minimum time and a maximum time between software clearing of the watchdog Time base accuracy 10% System enable output offers added security TTL/CMOS compatible to +85C temperature range DIP8 and SO8 packages

lated output voltage as low 1.2 V. The watchdog function monitors software cycle time and execution. If software clears the watchdog too quickly (incorrect cycle time) or too slowly (incorrect execution) it will cause the system to be reset. The system enable output prevents critical control functions being activated until software has successfully cleared the watchdog three times. Such a security could be used to prevent motor controls being energized on repeated resets of a faulty system.


Industrial electronics Cellular telephones Security systems Battery powered products High efficiency linear power supplies Automotive electronics


The A6130 offers a high level of integration by combining voltage regulation, voltage monitoring and software monitoring an 8 lead package. The voltage regulator has a low dropout voltage (typ. at 100 mA) and a low quiescent current (155 A). The quiescent current increases only slightly in dropout prolonging battery life. Built-in protection includes a positive transient absorber for 60 V (load dump) and the ability to survive an unregulated input voltage -20 V (reverse battery). The input may be connected to ground or a reverse voltage without reverse current flow from the output to the input. A comparator monitors the voltage applied at the VIN input comparing it with an internal 1.17 V reference. The power-on reset function is initialized after VIN reaches 1.17 V and takes the reset output inactive after TPOR depending of external resistance. The reset output goes active low when the VIN voltage is less than 1.17 V. The RES and EN outputs are guaranteed in a correct state for a regu-

Continuous voltage at INPUT to VSS Transients on INPUT for 100 ms and duty cycle 1% Reverse supply voltage on INPUT Max. voltage at any signal pin Min. voltage at any signal pin Storage temperature Electrostatic discharge max. To MIL-STD-883C method 3015 Max. soldering conditions

Operating junction temperature1) INPUT voltage 2) OUTPUT voltage 2) 3) RES & EN guaranteed 4) OUTPUT current 5) Comparator input voltage RC-oscillator programming Thermal resistance from junction to ambient - SO8


Table 1 Stresses above these listed maximum ratings may cause permanent damage to the device. Exposure beyond specified operating conditions may affect device reliability or cause malfunction.

The maximum operating temperature is confirmed by sampling at initial device qualification. In production, all devices are tested +85C. 2) Full operation guaranteed. To achieve the load regulation specified in Table 22 F capacitor or greater is required on the INPUT, see Fig. 8. The 22 F must have an effective resistance 5 W and a resonant frequency above 500 kHz. 10 F load capacitor and 100 nF decoupling capacitor are required on the regulator OUTPUT for stability. The 10 F must have an effective series resistance 5 W and a resonant frequency above 500 kHz. 4) RES must be pulled up externally to VOUTPUT even it is unused. (Note: RES and EN are used as inputs by EM test.) 5) The OUTPUT current will not apply for all possible combinations of input voltage and output current. Combinations that would require the A6130 to work above the maximum junction temperature (+85C) must be avoided. 6) The thermal resistance specified assumes the package is soldered to a PCB.

This device has built-in protection against high static voltages or electric fields; however, anti-static precautions must be taken as for any other CMOS component. Unless otherwise specified, proper operation can only occur when all terminal voltages are kept within the supply voltage range. At any time, all inputs must be tied to a defined logic voltage level.

Supply current in standby mode Supply current 1) Supply current 1)

ISS REXT = don't care, TCL = VOUTPUT, VIN 100 A REXT = 100 kW, I/Ps at VOUTPUT, O/Ps MW to VOUTPUT, 100 A REXT = 100 kW, I/Ps at VOUTPUT, VINPUT 8.0 V, O/Ps 1MW to VOUTPUT, 100 mA, V VINPUT = 1 mA, = 100 mA, +85C VINPUT = 100 A, REXT = 100 kW, O/Ps MW to VOUTPUT, I/Ps at VOUTPUT = 50 mA, VINPUT 10 ms OUTPUT tied to VSS

Output voltage Output voltage Output voltage temperature coefficient 2) Line regulation 3) Load regulation 3) Dropout voltage4) Dropout voltage4) Dropout voltage4) Dropout supply current

Thermal regulation 5) Current limit OUTPUT noise, to 100kHz

3.0 VOUTPUT = 100 A. + 100 nF, CINPUT = 22 F, to +85C, unless otherwise specified RES and EN Output Low Voltage VOL VOH VIL VIH ILI RVIN VREF VHY VOUTPUT 4.5 V, IOL 20 mA VOUTPUT 4.5 V, IOL 8 mA VOUTPUT 2.0 V, IOL 4 mA VOUTPUT 1.2 V, IOL 0.5 mA VOUTPUT 4.5 V, IOH -1 mA VOUTPUT 2.0 V, IOH -100 A VOUTPUT 1.2 V, IOH 1.8 1.0 VSS 2.0 VSS VTCL VOUTPUT +70C VOUTPUT V mV

TCL and VIN TCL Input Low Level TCL Input High Level Leakage current TCL input VIN input resistance Comparator reference 6)7)

If INPUT is connected to VSS, no reverse current will flow from the OUTPUT to the INPUT, however the supply current specified will be sank by the OUTPUT to supply the A6130. 2) The OUTPUT voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. 3) Regulation is measured at constant junction temperature using pulse testing with a low duty cycle. Changes in OUTPUT voltage due to heating effects are covered in the specification for thermal regulation. 4) The dropout voltage is defined as the INPUT to OUTPUT differential, measured with the input voltage equal V. 5) Thermal regulation is defined as the change in OUTPUT voltage at a time T after a change in power dissipation is applied, excluding load or line regulation effects. 6) The comparator and the voltage regulator have separate voltage references (see Block Diagram Fig. 7). 7) The comparator reference is the power-down reset threshold. The power-on reset threshold equals the comparator reference voltage plus the comparator hysteresis (see Fig. 4).


Related products with the same datasheet
Some Part number from the same manufacture EM Microelectronic
A6130SO8A 5V Accurate Regulator With Integrated Windowed Watchdog.
A6150 5V Accurate Regulator With Integrated Windowed Watchdog
A6155 5V Regulator With Integrated Windowed Watchdog And Sleep Mode Detection
A6250 5V Regulator With Integrated Windowed Watchdog in Power Package
A6300 5V Accurate Regulator With Timeout Reset Function (no Watchdog)
EM4005 134KHz, ISO 11'784 / 11'785 Compliant Read Only Contactless Identification Device
EM4006 13.56MHz, 82 Bit Read Only Contactless Identification Device
EM4022 125KHz to 2.45GHz, 64 Bit Read Only Anticolision Contactless Identification Device
EM4025 125KHz, Anticollision Read Only Cid
EM4055 125KHz, 1 Kbit Read/write Contactless Identification Device With Fast Anticollision Protocol
EM4056 125KHz, 2 Kbit Read Write Contactless Identification Device With Anti-collision
EM4069 125KHz-134KHz, 128 Bit Read Write Contactless Identification Device With OTP Function
EM4095 125KHz-134 Khz, Read Write Analog Front End For Rfid Basestation
EM4100 125KHz, 64 Bit Read Only Contactless Identification Device
EM4102 125KHz, 64 Bit Read Only Cid For Direct Coil Connection
EM4105 134KHz, ISO 11'784 / 11'785 Compliant Read Only Contactless Identification Device
EM4125 125KHz, Anticollision Read Only Cid
EM4150 125KHz, 1 Kbit Read Write Contactless Identification Device

EM6626WS11- : Ultra-low Power Microcontroller With 4x32 LCD Driver

V617314P : Power Accurate Voltage Window Surveillance, Software Monitoring And Chip Select

V6340JSP3B : Power Low Cost 3-Pin Voltage Detector

V6340NSP3B : Power Low Cost 3-Pin Voltage Detector

EM6325DX-2.6 : Reset Circuit with Manual Reset

EM6352XSP5B1.3 : Voltage Detector, High-precision

EM4450A6WW11 : 1 KBit Read/write Contactless Identification Device

EM4350A6WP7 : 1 KBit READ / Write Contactless Identification Device

0-C     D-L     M-R     S-Z