Details, datasheet, quote on part number: FAN1582x15
PartFAN1582x15
CategoryPower Management => Regulators => Linear Regulators => LDO (Low Drop Out)
Description3A Fixed 1.5V Low Dropout Voltage Regulator (LDO)
CompanyFairchild Semiconductor
DatasheetDownload FAN1582x15 datasheet
  

 

Features, Applications

Features

Ultra Low dropout voltage, 0.4V typical at 3A Remote sense operation Fast transient response Load regulation: 0.05% typical 0.5% initial accuracy On-chip thermal limiting 5-Pin SPAK, TO-252 DPAK, and TO-263 packages

Description

The FAN1582, FAN1582-1.5, and FAN1582-2.5 are ultra-low dropout regulators with 3A output current capability. These devices have been optimized for low voltage applications including VTT bus termination, where transient response and minimum input voltage are critical. The FAN1582 is ideal for low voltage microprocessor applications requiring a regulated output from to 5.7V with a power input supply to 6.5V. The FAN1582-1.5 offers fixed 1.5V with 3A current capabilities for GTL+ bus VTT termination. The FAN1582-2.5 offers fixed 2.5V with 3A current capability for logic IC operation and processors while minimizing the overall power dissipation. Current limit ensures controlled short-circuit current. On-chip thermal limiting provides protection against any combination of overload and ambient temperature that would create excessive junction temperatures. The FAN1582 series regulators are available in the 5-Pin SPAK, TO-252 DPAK, and TO-263 power packages.

Applications

Pentium® Processors PowerPCTM, AMD K5 and K6 processors Pentium support of GTL+ bus supply Low voltage logic supply Embedded Processor supplies Split plane regulator New 2.5V and 1.8V Logic Families

Typical Applications

VIN 3.3V 10µF VIN 3.3V 10µF VCNTL 5V + VIN VSENSE VCNTL + 22µF VIN 5.75V 10µF VCNTL 12V + VIN VSENSE + VIN VSENSE FAN1582­2.5 VOUT VCNTL GND

Pentium is a registered trademark of Intel Corporation. PowerPC is a trademark of IBM Corporation.

FAN1582M-1.5, -2.5 FRONT VIEW FAN1582M FRONT VIEW FAN1582P FRONT VIEW FAN1582P-1.5, -2.5 FRONT VIEW FAN1582D FRONT VIEW FAN1582D-1.5, -2.5 FRONT VIEW


*With package soldered to 0.5 square inch copper area over backside ground plane or internal power plane, JA can vary from 30 °C/W to more than 40 °C/W. Other mounting techniques can provide a thermal resistance lower than 30 °C/W.

Pin Function Descrition Remote Voltage Sense. Connect this pin to the load to permit true remote sensing and avoid trace drops. Adjust or Ground. On the FAN1582, this pin forms the feedback to determine the output voltage. On the FAN1582-1.5 and -2.5, connect this pin to ground. Output Voltage. This pin and the tab are output. Control Voltage. This pin draws small-signal power to control the FAN1582 circuitry. Connect to a voltage higher than VIN, as shown in the applications circuits. Input Voltage.

Thermal Shutdown Current Limit 3 Output 1 Sense 2 Adj

Parameter VIN VCNTL Operating Junction Temperature Range Lead Temperature (Soldering, 10 sec.) Storage Temperature Range -65 0 Min. Max. Unit V °C

TJ=25°C, VOUT = VS, VADJ = 0V unless otherwise specified. The denotes specifications which apply over the specified operating temperature range. Parameter Reference Voltage3 Reference Voltage3 Conditions VIN = 2.0V, VCNTL = 2.75V, IOUT 10mA 2.05V VIN 5.5V, 2.7V VCNTL 12V, 10mA IOUT 3A 3V VIN 7V (function of Vout), 10mA IOUT 3A 3V VIN 7V, 10mA IOUT 3A 5.1V VIN 7V, 10mA IOUT 3A 1.75V VIN 5.5V, 2.5V VCNTL 12V, IOUT = 10mA VIN = 2.1V, VCNTL 2.75V, 10mA IOUT 3A VIN = 2.05V, VREF = 1%, IOUT = 3A VCNTL = 2.75V, VREF = 1%, IOUT = 3A VCNTL = 2.75V, VREF = 1%, IOUT = 3A VIN = 2.05V, VCNTL = 2.75V VIN = 2.05V, VCNTL = 2.75V, IOUT = 10mA VIN = 2.05V, VCNTL = 2.75V VIN = 3.3V, VCNTL = 5V VIN = 3.75V, VCNTL = 120Hz, COUT = 22µF Tantalum, IOUT 1.5A TO-263/TO-252 SPAK 25°C, 30ms pulse Min. 1.243 1.237 Typ. 1.250 Max. 1.257 1.263 Units V

Adjustable Output Voltage Output Voltage4 Output Voltage5 Line Regulation1,2 Load Regulation1,2 Dropout Voltage Minimum (VCNTL­VOUT) Dropout Voltage Minimum (VIN­VOUT) Dropout Voltage Minimum VIN Current Limit Control Pin Current Adjust Pin Current3 Minimum Load Current Ripple Rejection Thermal Resistance, Junction to Case Thermal Regulation Thermal Shutdown

Notes: 1. See thermal regulation specifications for changes in output voltage due to heating effects. Load and line regulation are measured at a constant junction temperature by low duty cycle pulse testing. 2. Line and load regulation are guaranteed up to the maximum power dissipation (18W). Power dissipation is determined by input/output differential and the output current. Guaranteed maximum output power will not be available over the full input/ output voltage range. 3. FAN1582 only. 4. FAN1582-1.5 only. 5. FAN1582-2.5 only.


 

Related products with the same datasheet
FAN1582x25
Some Part number from the same manufacture Fairchild Semiconductor
FAN1582x25 3A Fixed 1.5V Low Dropout Voltage Regulator (LDO)
FAN1585A 5A Adjustable/fixed Low Dropout Linear Regulator
FAN1587A 3A Adjustable/fixed Low Dropout Linear Regulator
FAN1587Ax15
FAN1589 2.7A, 1.2V Low Dropout Linear Regulator For VRM8.5
FAN1616A 0.5A Adjustable/fixed Low Dropout Linear Regulator
FAN1616Ax18
FAN1654 1A LDO, DDR Bus Termination Regulator
FAN1655 FAN1655 - 3A DDR Bus Termination Regulator
FAN1950 1.5A Low Voltage LDO
FAN1951
FAN2011 High-efficiency Step-down DC/DC Converter
FAN2012
FAN2500 Low-dropout Voltage Regulator
FAN2500x25
FAN2501 100 ma CMOS LDO Regulators

DM74ALS163BMX : Bipolar->ALS Family Synchronous Four-bit Binary Counter With Synchronous Clear

KA5S1265 : Off-Line Fairchild Power Switch(sps)

SFU9034 : 60V P-channel A-FET

FAN3224CMX : Dual 4A High-Speed, Low-Side Gate Driver The FAN3223-25 family of dual 4A gate drivers is designed to drive N-channel enhancement-mode MOSFETs in low-side switching applications by providing high peak current pulses during the short switching intervals. The driver is available with either TTL or CM

MR33519MP8A : LED , Round with Domed Top, 5mm 12V 13mA Yellow (x 4) Through Hole, Right Angle; LED SS 12V QUAD YLW DIFF PCB 5MM Specifications: Color: Yellow (x 4) ; Mounting Type: Through Hole, Right Angle ; Configuration: 4 wide ; Voltage Rating: 12V ; Current: 13mA ; Lens Style/Size: Round with Domed Top, 5mm ; Packaging: Bulk ; Lens Type: Diffused, Tinted

HUF75631SK8T : Fet - Single Discrete Semiconductor Product 5.5A 100V 2.5W Surface Mount; MOSFET N-CH 100V 5.5A 8-SOP Specifications: Mounting Type: Surface Mount ; FET Type: MOSFET N-Channel, Metal Oxide ; Drain to Source Voltage (Vdss): 100V ; Current - Continuous Drain (Id) @ 25° C: 5.5A ; Rds On (Max) @ Id, Vgs: 39 mOhm @ 5.5A, 10V ; Input Capacitance (Ciss) @ Vds: 1225pF @ 25V ; Power - Max: 2.5W ; Packaging:

H11F13S : Optoisolator - Transistor, Photovoltaic Output Channel Surface Mount 6-SMD; OPTOCOUPLER FET BILAT VDE 6-SMD Specifications: Voltage - Isolation: 5300Vrms ; Input Type: DC ; Output Type: Photo FET ; Current - Output / Channel: - ; Voltage - Output: 30V ; Vce Saturation (Max): - ; Current Transfer Ratio (Min): - ; Mounting Type: Surface Mount ; Package / Case: 6-SMD ; Packaging: Tube ; Lead Free Status: Lea

BC856BL99Z : 100 mA, 65 V, PNP, Si, SMALL SIGNAL TRANSISTOR Specifications: Polarity: PNP

Same catergory

EPH3R3030 : Sidac / Uni-directional Thyristor (G1V Series). Characteristics Conditions 48 V Output Min. 3.2 0 Output Over Current Limit = Io Max. 20 Hz~5 MHz Hz ~50 MHz 30 Typ. Max. 3.46 3 Unit dB µV Output Voltage Initial Setting Line Regulation Load Regulation Po Max Output Over Voltage Protection Output Low Voltage Protection Voac Output Ripple & Noise Characteristics Conditions 48 V Min. Typ. 84 1.8 Max.

MC33063A : Dc-to-dc Converter Control Circuit. The MC34063A Series is a monolithic control circuit containing the primary functions required for DC­to­DC converters. These devices consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch. This series was specifically designed.

NCP512 : . The NCP512 series of fixed output linear regulators are designed for handheld communication equipment and portable battery powered applications which require low quiescent. The NCP512 series an ultra­low quiescent current of 40 mA. Each device contains a voltage reference unit, an error amplifier, a PMOS power transistor, resistors for setting output.

NCP5355D : MOSFET/IGBT Drivers. Ana Buck PWR MOSFET Drivr, Package: Soic, Pins=8.

PT5107A : Plug-in Power Solutions->Non-Isolated->Single Posi. ti PT5107, 15Vout 1A Wide Input Positive Step-down Isr.

PT6935A : Plug-in Power Solutions->Non-Isolated->Multiple Ou. ti PT6935, 2.5V/1.8V 9.5 Amp 5V/3.3V-Input Dual Output Isr.

PT7716A : Plug-in Power Solutions->Non-Isolated->Single Posi. ti PT7716, 20-A 1.075V to 1.85V 3.3V-Input Programmable Isr.

PT7743A : Plug-in Power Solutions->Non-Isolated->Single Posi. ti PT7743, 20 Amp 'Current Booster' For PT7709 Isr.

REF3130 : 20ppm/C Max, 100uA, SOT23-3 Series Voltage Referencethe REF31xx is a Family of Precision, Low Power, Low Dropout, Series Voltage References Available in The Tiny SOT23-3 Package..

ST3L01 : Triple Voltage Regulator. DUAL INPUT VOLTAGE (12V AND 5V) TRIPLE OUTPUT VOLTAGE 8V) 2.6V GUARANTEED IOUT 1.2A 3.3V GUARANTEED IOUT 1.0A 8V GUARANTEED IOUT TO 200mA THERMAL AND SHORT CIRCUIT PROTECTION GUARANTEED OPERATING TEMPERATURE RANGE to 125°C) This device contains three voltage regulators, all fixed output voltage, in one 7 pin surface mount package. The first 2.6 V regulator.

TDD25-03S2 : DC-DC Converter 25Watt. LOW COST & 3:1 WIDE INPUT RANGE I/O ISOLATION INPUT Pi FILTER SHORT CIRCUIT PROTECTION HIGH PERFORMANCE 2 YEARS WARRANTY OUTPUT WATTAGE VOLTAGE Single Output Models Block diagram for TDD25 series with single output Vi + Switching Device Vi Opto Isolation Reference & Error Amp. Rectifier Block diagram for TDD25 series with dual output Vi + Rectifier.

TLE6262G : Supply. Systemintegration of Transceiver And Voltage Regulator. Standard fault tolerant differential CAN-transceiver (TLE6254 LS CAN cell) Bus failure management Low power mode management CAN data transmission rate to 125 kBaud Low-dropout voltage regulator ± 2% Two Low Side Switches Three High Side Switches Power on and under-voltage reset generator Vcc supervisor Window watchdog Programable time base Integrated.

TMC211 : Microstepping Stepper Motor Controller/driver With Lin Interface. Micro Stepping Stepper Motor Controller / Driver with LIN Interface The is a combined micro-stepping stepper motor motion controller and driver with RAM and OTP memory. The RAM or OTP memory is used to store motor parameters and configuration settings. The TMC211 allows up to four bit of microstepping and a coil current to 800 mA. After initialization.

TPS61092RSAR : Switching DC/DC Converters, Integrated Switch. ti TPS61092, 5-V Output, 500-mA, 96% Efficient Boost Converter, 20uA, QFN-16.

ISL6609 : Synchronous Rectified MOSFET Driver The ISL6609, ISL6609A is a high frequency, MOSFET driver optimized to drive two N-Channel power MOSFETs in a synchronous-rectified buck converter topology. This driver combined with an Intersil ISL63xx or ISL65xx multiphase PWM controller forms a complete single-stage core-voltage regulator solution with high efficiency.

SRDB-04HX20 : NON-ISOLATED DC/DC CONVERTERS The SRDB-04HX20 is part of the low cost non-isolated dc/dc converter. The module uses a DIP package for ease of layout and space savings, with a low profile of 8.5 mm. The output is closely regulated and the efficiency of 12 V is typically 86% at full load. include remote sense, over current protection and remote on/off..

TPS60255 : 7-Channel, High Efficiency 175-mA Charge Pump For White LED Backlight The TPS60255 is a high-efficiency, constant frequency charge pump DC/DC converter that uses 1× and 1.5× conversion to maximize efficiency for the input voltage range. By using adaptive 1×/1.5× charge-pump modes and very low dropout current regulators, the TPS60255 achieves high efficiency.

TPS54318 : 2.95V To 6V Input, 2A, 2MHz Synchronous Step Down SWIFT™ DCDC Converter The TPS54218 device is a full featured 6 V, 2 A, synchronous step down current mode converter with two integrated MOSFETs. The TPS54218 enables small designs by integrating the MOSFETs, implementing current mode control to reduce external component count, reducing inductor size.

NJM2344 : PWM DC/DC Converter IC With Standby Function The NJM2344 is a general purpose PWM DC/DC converter IC configurable for step-up, step-down and inverting applications.An internal 1.5A power transistor, a pulse-by pulse current limit and 1% precision reference make the NJM2344 suitable for a wide range of voltage converter needs. The NJM2344 a standby function.

 
0-C     D-L     M-R     S-Z