|
Details, datasheet, quote on part number:NC7SZ66P5X
| |
Datasheet text preview:
NC7SZ66 · FSA66 TinyLogic Low Voltage UHS Single SPST Normally Open Analog Switch or 1-Bit Bus Switch
November 1996 Revised January 2003
NC7SZ66 · FSA66 TinyLogic Low Voltage UHS Single SPST Normally Open Analog Switch or 1-Bit Bus Switch
General Description
The NC7SZ66 or FSA66 is a ultra high-speed (UHS) CMOS compatible single-pole/single-throw (SPST) analog switch or 1-bit bus switch. The LOW on resistance of the switch allows input to be connected to output with minimal propagation delay and without generating additional ground bounce noise. The device is organized as a 1-bit switch with a switch enable (OE) signal. When OE is HIGH, the switch is on and Port A is connected to Port B. When OE is LOW, the switch is open and a high-impedance state exists between the two ports.
Features
s Space saving SOT23 or SC70 5-lead package s Ultra small MicroPak leadless package s Broad VCC Operating Range 1.65V5.5V s Rail-to-Rail signal handling s 5 switch connection between two ports s Minimal propagation delay through the switch s Low ICC s Zero bounce in flow-through mode s Control input compatible with CMOS input levels s >250 MHz -3dB bandwidth
Ordering Code:
Order Number NC7SZ66M5X NC7SZ66P5X NC7SZ66L6X FSA66M5X FSA66P5X FSA66L6X Package Number MA05B MAA05A MAC06 MA05B MAA05A MAC06 Product Code Top Mark 7Z66 Z66 EE 7Z66 Z66 EE Package Description 5-Lead SOT23, JEDEC MO-178, 1.6mm 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 6-Lead MicroPak, 1.0mm Wide 5-Lead SOT23, JEDEC MO-178, 1.6mm 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 6-Lead MicroPak, 1.0mm Wide Supplied As 3k Units on Tape and Reel 3k Units on Tape and Reel 5k Units on Tape and Reel 3k Units on Tape and Reel 3k Units on Tape and Reel 5k Units on Tape and Reel
TinyLogic is a registered trademark and MicroPak is a trademark of Fairchild Semiconductor Corporation.
© 2003 Fairchild Semiconductor Corporation
DS012177
www.fairchildsemi.com
NC7SZ66 · FSA66
Logic Symbol
Analog Symbol
Pin Descriptions
Pin Names OE A B NC Description Switch Enable Input Bus A I/O Bus B I/O No Connect Pin Assignments for SC70
Connection Diagrams
Function Table
OE L H B0 HIGH-Z State A0 Function Disconnect Connect (Top View) Pad Assignment for MicroPak
(Top Thru View)
www.fairchildsemi.com
2
NC7SZ66 · FSA66
Absolute Maximum Ratings(Note 1)
Supply Voltage (VCC ) DC Switch Voltage (VS) DC Input Voltage (VIN) (Note 2) DC Input Diode Current (IIK) VIN < 0V DC Output (IOUT ) Sink Current DC VCC/GND Current (ICC/IGND) Storage Temperature Range (TSTG) Junction Lead Temperature under Bias (TJ) Junction Lead Temperature (TL) (Soldering, 10 Seconds) Power Dissipation (PD) @ +85°C SOT23-5 SC70-5 200 mW 150 mW
-0.5V to +7.0V -0.5V to VCC +0.5V -0.5V to +7.0V -50 mA
128 mA
Recommended Operating Conditions (Note 3)
Power Supply Operating (VCC) Control Input Voltage (VIN) Switch Input Voltage (VIN) Switch Output Voltage (VOUT) Input Rise and Fall Time (tr, tf) Control Input; VCC = 2.3V-3.6V Control Input; VCC = 4.5-5.5V Switch I/O Operating Temperature (TA) Thermal Resistance (JA) SOT23-5 300°C/Watt 425°C/Watt SC70-5 0 ns/V to 10 ns 0 ns/V to 5 ns 0 ns/V to DC 1.65V to 5.5V 0V to 5.5V 0V to VCC 0V to VCC
±100 mA -65°C to +150°C +150°C +260°C
-40°C to +85°C
Note 1: The "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The "Recommended Operating Conditions" table will define the conditions for actual device operation. Note 2: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 3: Unused inputs must be held HIGH or LOW. They may not float.
DC Electrical Characteristics
VCC Symbol VIH VIL IIN IOFF RON Parameter HIGH Level Input Voltage LOW Level Input Voltage Control Input Leakage Current OFF Leakage Current Switch On Resistance (Note 4) 4.5 (V) TA= -40°C to +85°C Min Typ (Note 5) Max M in TA = +25°C Typ M ax Units Conditions
1.65 to 1.95 0.75 VCC 2.3 to 5.5 1.65 to 1.95 2.3 to 5.5 0 to 5.5 1.65 to 5.5 ±0.05 ±0.05 3 5 7 3.0 2.3 1.8 4 10 5 13 7 25 0.7 VCC 0 . 2 5 V CC 0.3 VCC ±1.0 ±10.0 7 12 15 9 20 12 30 28 60 6 12 28 125 0.05 10
V V µA µA 0 VIN 5.5V 0 A, B VCC VIN = 0V, IIN = 30 mA VIN = 2.4V, IIN = 15 mA VIN = 4.5V, IIN = 30 mA VIN = 0V, IIN = 24 mA VIN = 3V, IIN = 24 mA VIN = 0V, IIN = 8 mA VIN = 2.3V, IIN = 8 mA VIN = 0V, IIN = 4 mA VIN = 1.8V, IIN = 4 mA IA = -30 mA, 0 VBn VCC IA = -24 mA, 0 VBn VCC IA = -8 mA, 0 VBn VCC IA = -4 mA, 0 VBn VCC µA VIN = VCC or GND IOUT = 0
Rflat
On Resistance Flatness (Note 4)(Note 6)(Note 7)
5 .0 3.3 2.5 1.8
ICC
Quiescent Supply Current
1.65 to 5.5
Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the voltages on the two (A or B) pins. Note 5: All typical values are at the specified VCC, and TA = 25°C. Note 6: Parameter is characterized but not tested in production. Note 7: Flatness is defined as the difference between the maximum and minimum value of On Resistance over the specified range of conditions.
3
www.fairchildsemi.com
|
|
