|
Details, datasheet, quote on part number:74FCT2257T
| |
Datasheet text preview:
IDT74FCT2257AT/CT FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
FAST CMOS QUAD 2-INPUT M U LT I P L E X E R
FEATURES:
· · · · · · · ·
IDT74FCT2257AT/CT
A and C grades Low input and output leakage 1µA (max.) CMOS power levels True TTL input and output compatibility: VOH = 3.3V (typ.) VOL = 0.3V (typ.) Meets or exceeds JEDEC standard 18 specifications Resistor outputs (-15mA IOH, 12mA IOL) Reduced system switching noise Available in SOIC and QSOP packages
DESCRIPTION:
The FCT2257T is a high-speed quad 2-input multiplexer built using an advanced dual metal CMOS technology. Four bits of data from two sources can be selected using the common select input. The four buffered outputs present the selected data in the true (non-inverting) form. The 2257T has a common Output Enable (OE) input. When OE is high, all outputs are switched to a high-impedance state allowing the outputs to interface directly with bus-oriented systems. The FCT2257T has balanced output drive with current limiting resistors. This offers low ground bounce, minimal undershoot and controlled output fall times-reducing the need for external series terminating resistors. FCT2257T parts are plug-in replacements for FCT257T parts.
FUNCTIONAL BLOCK DIAGRAM
S
T h r e e other multiplexers
I1 B I0 B
I1 D I0 D
ZB ZD
I1A I0A
ZA
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
1
JUNE 2002
DSC-5501/2
© 2002 Integrated Device Technology, Inc.
IDT74FCT2257AT/CT FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS(1)
Symbol VTERM(2) Description Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Storage Temperature DC Output Current Max 0.5 to +7 0.5 to VCC+0.5 65 to +150 60 to +120 Unit V V °C mA VTERM(3) TSTG IOUT
S I0A I1A ZA I0B I1B ZB GND
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
VCC OE I0C I1C ZC I0D I1D ZD
NOTES: 1 . Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. No terminal voltage may exceed Vcc by +0.5V unless otherwise noted. 2 . Inputs and Vcc terminals only. 3 . Output and I/O terminals only.
CAPACITANCE (TA = +25°C, F = 1.0MHz)
Symbol CI N CO U T Parameter(1) Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 6 8 Max. 10 12 Unit pF pF
SOIC/ QSOP TOP VIEW
NOTE: 1 . This parameter is measured at characterization but not tested.
PIN DESCRIPTION
Pin Names I0AI0D I1AI1D OE S ZAZD Source 0 Data Inputs Source 1 Data Inputs Output Enable (Active LOW) Select Input Outputs Description
FUNCTION TABLE(1)
Inputs OE H L L L L S X H H L L I0 X X X L H I1 X L H X X Outputs Z L H L H
NOTE: 1 . H = HIGH Voltage Level L = LOW Voltage Level X = Don't Care Z = High-Impedance
2
IDT74FCT2257AT/CT FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified: Industrial: TA = 40°C to +85°C, VCC = 5.0V ±5%
Symbol VIH VIL IIH IIL IOZH IOZL II VIK VH ICC Parameter Input HIGH Level Input LOW Level Input HIGH Current(4) Input LOW Current(4) High Impedance Output Current (3-State Output Pins)(4) Input HIGH Current(4) Clamp Diode Voltage Input Hysteresis Quiescent Power Supply Current VCC = Max. VIN = GND or VCC VCC = Max., VI = VCC (Max.) VCC = Min., IIN = 18mA -- Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VCC = Max. VCC = Max. VI = 2.7V VI = 0.5V VI = 2.7V VI = 0.5V Min. 2 -- -- -- -- -- -- -- -- -- Typ.(2) -- -- -- -- -- -- -- 0.7 200 0.01 Max. -- 0.8 ±1 ±1 ±1 ±1 ±1 1.2 -- 1 µA V mV mA Unit V V µA µA µA
OUTPUT DRIVE CHARACTERISTICS
Symbol IODL IODH VOH VOL Parameter Output LOW Current Output HIGH Current Output HIGH Voltage Output LOW Voltage Test Conditions(1) VCC = 5V, VIN = VIH or VIL, VOUT = 1.5V(3) VCC = 5V, VIN = VIH or VIL, VOUT = 1.5V(3) VCC = Min IOH = 15mA VIN = VIH or VIL VCC = Min IOL = 12mA VIN = VIH or VIL Min. 16 -16 2.4 -- Typ.(2) 48 -48 3.3 0.3 Max. -- -- -- 0.5 Unit mA mA V V
NOTES: 1 . For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2 . Typical values are at VCC = 5.0V, +25°C ambient. 3 . Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4 . The test limit for this parameter is ±5µA at TA = -55°C.
3
IDT74FCT2257AT/CT FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol ICC ICCD Parameter Quiescent Power Supply Current TTL Inputs HIGH Dynamic Power Supply Current(4) VCC = Max. VIN = 3.4V(3) VCC = Max. Outputs Open OE = GND One Input Toggling 50% Duty Cycle IC Total Power Supply Current(6) VCC = Max. Outputs Open fo = 10MHz 50% Duty Cycle OE = GND One Bit Toggling VCC = Max. Outputs Open fo = 2.5MHz 50% Duty Cycle OE = GND Four Bits Toggling VIN = VCC VIN = GND VIN = 3.4V VIN = GND VIN = VCC VIN = GND VIN = 3.4V VIN = GND -- 0.6 2.2 mA VIN = VCC VIN = GND Test Conditions(1) Min. -- -- Typ.(2) 0.5 0.06 Max. 2 0.12 Unit mA mA/ MHz
--
0.9
3.2
--
0.6
2.2(5)
--
1.6
6.2(5)
NOTES: 1 . For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2 . Typical values are at VCC = 5.0V, +25°C ambient. 3 . Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND. 4 . This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5 . Values for these conditions are examples of ICC formula. These limits are guaranteed but not tested. 6 . IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ICC DHNT + ICCD (fONO) ICC = Quiescent Current ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current caused by an Input Transition Pair (HLH or LHL) fO = Output Frequency NO = Number of Outputs at fO All currents are in milliamps and all frequencies are in megahertz.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
74FCT2257AT Symbol tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Propagation Delay Ix to Zx Propagation Delay S to Zx Output Enable Time Output Disable Time Condition(1) CL = 50pF RL = 500 CL = 50pF M i n .( 2 ) 1.5 1.5 1.5 1.5 Max. 5 7 7 5.5 74FCT2257CT M i n .( 2 ) 1.5 1.5 1.5 1.5 Max. 4.3 5.2 6 5 Unit
ns ns ns ns
NOTES: 1 . See test circuit and waveforms. 2 . Minimum limits are guaranteed but not tested on Propagation Delays.
4
IDT74FCT2257AT/CT FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
TEST CIRCUITS AND WAVEFORMS
V CC 500 VIN Pulse Generator RT D.U.T . V O UT 7.0V
SWITCH POSITION
Test Open Drain Disable Low Enable Low All Other Tests Switch Closed Open
50pF CL
500
DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
Octal link
Test Circuits for All Outputs
DATA INPUT TIMING INPUT ASYNCHRONOUS CONTROL PRESET CLEAR ETC. SYNCHRONOUS CONTROL PRESET CLEAR CLOCK ENABLE ETC.
tSU
tH
tREM
3V 1.5V 0V 3V 1.5V 0V 3V 1.5V 0V 3V 1.5V 0V
Octal link
LOW-HIGH-LOW PULSE tW HIGH-LOW-HIGH PULSE
Octal link
1.5V
1.5V
tSU
tH
Pulse Width
Set-Up, Hold, and Release Times
ENABLE SAME PHASE INPUT TRANSITION tPLH OUTPUT tPLH OPPOSITE PHASE INPUT TRANSITION tPHL tPHL 3V 1.5V 0V VOH 1.5V V OL 3V 1.5V 0V
Octal link
DISABLE 3V 1.5V
CONTROL INPUT t PZL OUTPUT NORMALLY LOW OUTPUT NORMALLY HIGH SWITCH CLOSED tPZH SWITCH OPEN 3.5V 1.5V tPHZ 0.3V 1.5V 0V tP L Z
0V 3.5V 0.3V V OL VOH 0V
Octal link
Propagation Delay
Enable and Disable Times
NOTES: 1 . Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. 2 . Pulse Generator for All Pulses: Rate 1.0MHz; tF 2.5ns; tR 2.5ns.
5
|
|
