Details, datasheet, quote on part number: IDT54FCT162244ATPFB
PartIDT54FCT162244ATPFB
Category
DescriptionFast CMOS 16-bit Buffer/line Driver
CompanyIntegrated Device Technology, Inc.
DatasheetDownload IDT54FCT162244ATPFB datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Common features: 0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) 250ps Low input and output leakage 1 A (max.) ESD > 2000V per MIL-STD-883, Method > 200V using machine model 0) Packages include 25 mil pitch SSOP, 19.6 mil pitch TSSOP, 15.7 mil pitch TVSOP and 25 mil pitch Cerpack Extended commercial range to +85C Features for FCT16244T/AT/CT/ET: High drive outputs (-32mA IOH, 64mA IOL) Power off disable outputs permit "live insertion" Typical VOLP (Output Ground Bounce) 1.0V at VCC = 25C Features for FCT162244T/AT/CT/ET: Balanced Output Drivers: 24mA (commercial), 16mA (military) Reduced system switching noise Typical VOLP (Output Ground Bounce) 0.6V at VCC = 25C Features for FCT166244T/AT/CT: Light Drive Balanced Output: 8mA (commercial), 6mA (military) Minimal system switching noise Typical VOLP (Output Ground Bounce) 0.25V at VCC = 25C Features for FCT162H244T/AT/CT/ET: Bus-Hold retains last active bus state during 3-state Eliminates the need for external pull up resistors

The 16-Bit Buffer/Line Driver is for bus interface or signal buffering applications requiring high speed and low power dissipation. These devices have a flow through pin organization, and shrink packaging to simplify board layout. All inputs are designed with hysteresis for improved noise margin. The three-state controls allow independent 8-bit or combined 16-bit operation. These parts are plug in replacements for 54/74ABT16244 where higher speed, lower noise or lower power dissipation levels are desired. The FCT16244T/AT/CT/ET are ideally suited for driving high capacitance loads (>200pF) and low impedance backplanes. These "high drive" buffers are designed with power off disable capability to allow "live insertion" of boards when used in a backplane interface. The FCT162244T/AT/CT/ET have balanced output current levels and current limiting resistors. These offer low ground bounce, minimal undershoot, and controlled output fall times, reducing the need for external series terminating resistors while still providing very high speed operation for loads of less than 200pF. The FCT166244T/AT/CT are suited for very low noise, point-to-point driving where there is a single receiver, or a very light lumped load (<100pF). The buffers are designed to limit the output current to levels which will avoid noise and ringing on the signal lines without using external series terminating resistors. The FCT162H244T/AT/CT/ET have "Bus-Hold" which retains the input's last state whenever the input goes to high impedance. This prevents "floating" inputs and eliminates the need for pull-up/down resistors.

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

Pin Names xOE xAx xYx Description 3State Output Enable Inputs (Active LOW) Data Inputs(1) 3-State Outputs

2544 tbl 01 NOTE: On FCT16xH these pins have "Bus-hold". All other pins are standard inputs, outputs or I/Os.

Symbol Description Max. VTERM(2) Terminal Voltage with Respect to +7.0 GND (3) Terminal Voltage with Respect to VTERM 0.5 to GND VCC +0.5 TSTG Storage Temperature +150 I OUT DC Output Current to +120 Unit C mA

NOTE: H = HIGH Voltage Level X = Don't Care L = LOW Voltage Level Z = High Impedance

2544 lnk 03 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXXT and FCT166XXXT output and I/O terminals. 3. Output and I/O terminals for FCT162XXXT and FCT166XXXT.

Symbol Parameter(1) CIN Input Capacitance COUT Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 3.5 Max. Unit pF 8.0

NOTE: 1. This parameter is measured at characterization but not tested.
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE (STANDARD PARTS)

Following Conditions Apply Unless Otherwise Specified: Commercial: to +85C, VCC 10%; Military: to +125C, VCC 10%

Symbol VIH VIL L I OZH I OZL VIK VH I CCL I CCH I CCZ Parameter Input HIGH Level Input LOW Level Input HIGH Current (Input pins)(5) Input HIGH Current (I/O pins)(5) Input LOW Current (Input pins)(5) VCC = Max. VCC = Min., IIN = 18mA VCC = Max., VO = GND (3)

Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VI = VCC VI = GND = 0.5V

Input LOW Current (I/O pins)(5) High Impedance Output Current (3-State Output pins) (5) Clamp Diode Voltage Short Circuit Current Input Hysteresis Quiescent Power Supply Current

NOTES: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc 5.0V, +25C ambient. 3. Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4. Duration of the condition can not exceed one second. 5. The test limit for this parameter = 55C.


 

Related products with the same datasheet
IDT54FCT162244ATE
IDT54FCT162244ATEB
IDT54FCT162244ATPA
IDT54FCT162244ATPAB
IDT54FCT162244ATPF
IDT54FCT162244ATPV
IDT54FCT162244ATPVB
IDT54FCT162244CT
IDT54FCT162244CTE
IDT54FCT162244CTEB
IDT54FCT162244CTPA
Some Part number from the same manufacture Integrated Device Technology, Inc.
IDT54FCT162244ATPV Fast CMOS 16-bit Buffer/line Driver
IDT54FCT162245 Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162245AT Fast CMOS 16-bit Bi-directional Transceiver
IDT54FCT162245ET Fast CMOS 16-bit Bidirectional Transceivers
IDT54FCT162245ETE Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT162245T Fast CMOS 16-bit Bi-directional Transceiver
IDT54FCT162260 Fast CMOS 12-bit Tri-port Bus Exchanger
IDT54FCT162260AT
IDT54FCT162260ET
IDT54FCT162344 Fast CMOS Address/clock Driver
IDT54FCT162344AT

72V3654 : 2K X 36 X 2 Syncbififo, 3.3V

IDT70V07S35G : High-speed 3.3v 32k X 8 Dual-port Static RAM

IDT70V9289L9PRF8 : 64K X 16 Sync, 3.3V Dual-port RAM, Pipelined/flow-through

IDT72421L20JB : CMOS Syncfifoo 64 X 9, 256 X 9, 512 X 9, 1024 X 9, 2048 X 9 And 4096 X 9

IDT74FCT373ATPB : CMOS/BiCMOS->FCT/FCT-T Family Fast CMOS Octal Transparent Latch

IDT7188S70DBG : 16K X 4 STANDARD SRAM, 15 ns, PDSO24 Specifications: Memory Category: SRAM Chip ; Density: 66 kbits ; Number of Words: 16 k ; Bits per Word: 4 bits ; Package Type: SOJ, 0.300 INCH, SOJ-24 ; Pins: 24 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 15 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

IDT72841L15TFG : 4K X 9 BI-DIRECTIONAL FIFO, 6.5 ns, PQFP64 Specifications: Memory Category: FIFO ; Density: 37 kbits ; Number of Words: 4 k ; Bits per Word: 9 bits ; Package Type: TQFP, TQFP-64 ; Pins: 64 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 6.5 ns ; Cycle Time: 10 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

71421LA20PF : 2K X 8 DUAL-PORT SRAM, 20 ns, PQCC52 Specifications: Memory Category: SRAM Chip ; Density: 16 kbits ; Number of Words: 2 k ; Bits per Word: 8 bits ; Package Type: 0.750 X 0.750 INCH, 0.170 INCH HEIGHT, PLASTIC, LCC-52 ; Pins: 52 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 20 ns ; Operating Temperature: 0 to 70 C (32 to 158

9FG1200DF-1LF : 400 MHz, OTHER CLOCK GENERATOR, PDSO56 Specifications: Device Type: Clock Generator ; Package Type: Surface Mount, SSOP, 0.300 INCH, 0.025 INCH PITCH, ROHS COMPLIANT, MO-118, SSOP-56 ; Supply Voltage: 3.14 to 3.46 volts ; Frequency: 400 MHz ; Operating Temperature: 0.0 to 70 C (32 to 158 F) ; Features / Standards: RoHS, Lead-Free

 
0-C     D-L     M-R     S-Z