Details, datasheet, quote on part number: IDT54FCT162373ETPF
PartIDT54FCT162373ETPF
CategoryLogic => Latches => CMOS/BiCMOS->FCT/FCT-T Family
TitleCMOS/BiCMOS->FCT/FCT-T Family
DescriptionFast CMOS 16-bit Transparent Latch
CompanyIntegrated Device Technology, Inc.
DatasheetDownload IDT54FCT162373ETPF datasheet
  

 

Features, Applications

0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) < 250ps Low input and output leakage 1µA (max.) VCC 5V ±10% Balanced Output Drivers: ±24mA Reduced system switching noise Typical VOLP (Output Ground Bounce) 0.6V at VCC = 25°C Available in SSOP and TSSOP packages

The FCT162373T 16-bit transparent D-type latch is built using advanced dual metal CMOS technology. This high-speed, low-power latch is ideal for temporary storage of data. It can be used for implementing memory address latches, I/O ports, and bus drivers. The Output Enable and Latch Enable controls are organized to operate each device as two 8-bit latches, or one 16-bit latch. Flow-through organization of signal pins simplifies layout. All inputs are designed with hysteresis for improved noise margin. The FCT162373T has balanced output drive with current limiting resistors. This offers low ground bounce, minimal undershoot, and controlled output fall times­reducing the need for external series terminating resistors. The is a plug-in replacement for the FCT16373T and ABT16373 for on-board interface applications.

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

Symbol Description Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Storage Temperature DC Output Current Max to +120 Unit °C mA

NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXX Output and I/O terminals. 3. Output and I/O terminals for FCT162XXX.

Symbol CIN COUT Parameter(1) Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 3.5 Max. 6 8 Unit pF

NOTE: 1. This parameter is measured at characterization but not tested.

Pin Names xDx xLE x OE xOx Data Inputs Latch Enable Input (Active HIGH) Outputs Enable Input (Active LOW) 3-State Outputs Description

NOTE: H = HIGH Voltage Level X = Don't Care L = LOW Voltage Level Z = High-Impedance
Following Conditions Apply Unless Otherwise Specified: Industrial: to +85°C, VCC 5.0V ±10%

Symbol VIH VIL IIH Parameter Input HIGH Level Input LOW Level Input HIGH Current (Input pins)(5) Input HIGH Current (I/O pins)(5) IIL Input LOW Current (Input pins)(5) Input LOW Current (I/O pins)(5) IOZH IOZL VIK IOS VH ICCL ICCH ICCZ High Impedance Output Current (3-State Output pins)(5) Clamp Diode Voltage Short Circuit Current Input Hysteresis Quiescent Power Supply Current VCC = Max. VIN = GND or VCC = Min., IIN = ­18mA VCC = Max., = GND(3) VCC = Max. = 0.5V VCC = Max. VI = GND Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VI = VCC Min. ­80 Typ.(2) Max. mV µA Unit V µA

Symbol IODL IODH VOH VOL Parameter Output LOW Current Output HIGH Current Output HIGH Voltage Output LOW Voltage Test Conditions(1) VCC = 5V, VIN = VIH or VIL, = 1.5V(3) VCC = 5V, VIN = VIH or VIL, = 1.5V(3) VCC = Min VIN = VIH or VIL VCC = Min VIN = VIH or VIL IOH = ­24mA IOL = 24mA Min. 2.4 Typ.(2) Max. ­200 0.55 Unit mA V

NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC 5.0V, +25°C ambient. 3. Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4. Duration of the condition can not exceed one second. 5. The test limit for this parameter = ­55°C.


 

Related products with the same datasheet
IDT54FCT162373ATE
IDT54FCT162373ATEB
IDT54FCT162373ATPA
IDT54FCT162373ATPAB
IDT54FCT162373ATPF
IDT54FCT162373ATPFB
IDT54FCT162373ATPV
IDT54FCT162373ATPVB
IDT54FCT162373CT
IDT54FCT162373CTE
IDT54FCT162373CTEB
IDT54FCT162373CTPA
Some Part number from the same manufacture Integrated Device Technology, Inc.
IDT54FCT162373ETPFB Fast CMOS 16-bit Transparent Latch
IDT54FCT162374 Fast CMOS 16-bit Register (3-state)
IDT54FCT162374AT
IDT54FCT16240 Fast CMOS 16-bit Buffer/line Driver
IDT54FCT16240AT
IDT54FCT16240T
IDT54FCT16244
IDT54FCT16244AT

74LVCH162721A : 3.3V CMOS 20-BIT Flip-flop With 3-STATE Outputs, 5V Tolerant I/O, And Bus-hold

IDT54FCT374CT : CMOS/BiCMOS->FCT/FCT-T Family Fast CMOS Octal D Registers (3-state)

IDT54FCT646CP : Bus Oriented Circuits Fast CMOS Octal Transceiver/register (3-state)

IDT72V2113L7PF : 3.3 VOLT HIGH Density CMOS Supersync FIFO 131,072 x 18 262,144 x 18

MPC9448FA : Clock/timing - Clock Buffers, Driver Integrated Circuit (ics) Fanout Buffer (Distribution), Multiplexer Tray 2.375 V ~ 3.465 V; IC CLK FAN BUFF MUX 1:12 32LQFP Specifications: Type: Fanout Buffer (Distribution), Multiplexer ; Frequency - Max: 350MHz ; Input: LVCMOS, LVPECL ; Output: LVCMOS ; Voltage - Supply: 2.375 V ~ 3.465 V ; Package / Case: 32-LQFP ; Packaging: Tray ; Lead Free Status: Contains Lead ; RoHS Status: RoHS Non-Compliant

IDT70V05L20JGI : 8K X 8 DUAL-PORT SRAM, 15 ns, CPGA68 Specifications: Memory Category: SRAM Chip ; Density: 66 kbits ; Number of Words: 8 k ; Bits per Word: 8 bits ; Package Type: 1.180 X 1.180 INCH, 0.160 INCH HEIGHT, GREEN, CERAMIC, PGA-68 ; Pins: 68 ; Logic Family: CMOS ; Supply Voltage: 3.3V ; Access Time: 15 ns ; Operating Temperature: 0 to 70 C (

IDT71421LA55JG : 2K X 8 MULTI-PORT SRAM, 100 ns, PQCC52 Specifications: Memory Category: SRAM Chip ; Density: 16 kbits ; Number of Words: 2 k ; Bits per Word: 8 bits ; Package Type: PLASTIC, LCC-52 ; Pins: 52 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 100 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

IDT72821L15TFGI : 1K X 9 BI-DIRECTIONAL FIFO, 6.5 ns, PQFP64 Specifications: Memory Category: FIFO ; Density: 9 kbits ; Number of Words: 1 k ; Bits per Word: 9 bits ; Package Type: TQFP, TQFP-64 ; Pins: 64 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 6.5 ns ; Cycle Time: 10 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

 
0-C     D-L     M-R     S-Z