Details, datasheet, quote on part number: IDT54FCT16244CTPVB
CategoryLogic => Bus Interface => Bus Oriented Circuits
TitleBus Oriented Circuits
DescriptionFast CMOS 16-bit Buffer/line Driver
CompanyIntegrated Device Technology, Inc.
DatasheetDownload IDT54FCT16244CTPVB datasheet
Find where to buy


Features, Applications

MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) < 250ps Low input and output leakage 1 A (max.) ESD > 2000V per MIL-STD-883, Method > 200V using machine model = 0) High drive outputs (-32mA IOH, 64mA IOL) Power off disable outputs permit "live insertion" Typical VOLP (Output Ground Bounce) 1.0V at VCC = 25C Available in the following packages: Industrial: SSOP, TSSOP, TVSOP Military: CERPACK

The FCT16244T 16-Bit Buffer/Line Driver is for bus interface or signal buffering applications requiring high speed and low power dissipation. These devices have a flow through pin organization, and shrink packaging to simplify board layout. All inputs are designed with hysteresis for improved noise margin. The three-state controls allow independent 8-bit or combined 16bit operation. These parts are plug in replacements for 54/74ABT16244 where higher speed, lower noise or lower power dissipation levels are desired. The FCT16244T is ideally suited for driving high capacitance loads (>200pF) and low impedance backplanes. These "high drive" buffers are designed with power off disable capability to allow "live insertion" of boards when used in a backplane interface.

Description Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Storage Temperature DC Output Current

NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXX Output and I/O terminals. 3. Output and I/O terminals for FCT162XXX. FCT162XXXT and FCT166XXXT.

Symbol CIN COUT Parameter(1) Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 3.5 Max. 6 8 Unit pF

NOTE: 1. This parameter is measured at characterization but not tested.

Pin Names xOE xAx xYx Description 3State Output Enable Inputs (Active LOW) Data Inputs 3-State Outputs

NOTE: H = HIGH Voltage Level X = Don't Care L = LOW Voltage Level Z = High-Impedance

Following Conditions Apply Unless Otherwise Specified: Industrial: to +85C, VCC 5.0V 10%; Military: to +125C, VCC 5.0V 10%

Symbol VIH VIL IIH IIL IOZH IOZL VIK IOS VH ICCL ICCH ICCZ Parameter Input HIGH Level Input LOW Level Input HIGH Current (Input pins)(5) Input HIGH Current (I/O pins)(5) Input LOW Current (Input pins)(5) Input LOW Current (I/O pins)(5) High Impedance Output Current (3-State Output pins)(5) Clamp Diode Voltage Short Circuit Current Input Hysteresis Quiescent Power Supply Current VCC = Max. VIN = GND or VCC = Min., IIN = 18mA VCC = Max., = GND(3) VCC = Max. VI = GND Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VI = VCC Min. 80 Typ.(2) Max. mV A Unit V A

Symbol IO VOH Parameter Output Drive Current Output HIGH Voltage Test Conditions(1) VCC = Max., = 2.5V(3) VCC = Min. VIN = VIH or VIL IOH = 3mA IOH = 12mA MIL IOH = 15mA IND IOH = 24mA MIL IOH 32mA IND(4) VOL IOFF Output LOW Voltage Input/Output Power Off Leakage(5) VCC = Min. VIN = VIH or VIL VCC = 0V, VIN VO 4.5V IOL = 48mA MIL IOL = 64mA IND 0.2 0.55 Min. Typ.(2) 3.5 Max. 180 Unit mA V

NOTES: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC 5.0V, +25C ambient. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Duration of the condition can not exceed one second. 5. The test limit for this parameter = -55C.


Related products with the same datasheet
Some Part number from the same manufacture Integrated Device Technology, Inc.
IDT54FCT16244ET Fast CMOS 16-bit Buffer/line Driver
IDT54FCT16245 Fast CMOS 16-bit Bidirectional Transceiver
IDT54FCT16245AT Fast CMOS 16-bit Bi-directional Transceiver
IDT54FCT162500 Fast CMOS 18-bit Registered Transceiver

74LVCH16260A : 3.3V CMOS 12-BIT Tri-port Bus Exchanger With 5V Tolerant I/o

IDT72261L12TFB : CMOS Supersync Fifoo 16,384 X 9, 32,768 X 9

IDT7381L30JB : Bipolar->F Family 16-bit CMOS Cascadable Alu

IDT74FCT2245CTSOB : Fast CMOS Octal Bidirectional Transceivers

IDT70V27L55PF : High-speed 3.3V 64K x 16 Dual-port Static RAM

MC100ES6011EJR2 : Clock/timing - Clock Buffers, Driver Integrated Circuit (ics) Fanout Buffer (Distribution) Tape & Reel (TR) 2.375 V ~ 3.8 V; IC FANOUT BUFFER ECL 8-TSSOP Specifications: Type: Fanout Buffer (Distribution) ; Frequency - Max: 3GHz ; Input: ECL ; Output: LVPECL ; Voltage - Supply: 2.375 V ~ 3.8 V ; Package / Case: 8-TSSOP (0.118", 3.00mm Width) ; Packaging: Tape & Reel (TR) ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

IDT7143LA25PFGI : 2K X 16 MULTI-PORT SRAM, 45 ns, CQFP68 Specifications: Memory Category: SRAM Chip ; Density: 33 kbits ; Number of Words: 2 k ; Bits per Word: 16 bits ; Package Type: QFP, QFP-68 ; Pins: 68 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 45 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

IDT7281L20SOB : 512 X 9 OTHER FIFO, 12 ns, PQCC32 Specifications: Communication Type: Asynchronous ; Production Status: Full Production ; Density: 5 kbits ; Number of Words: 512 k ; Bits per Word: 9 bits ; Access Time: 12 ns ; Logic Family: CMOS ; Supply Voltage: 5V ; Package Type: PLASTIC, LCC-32 ; Operating Range: Commercial ; Pins: 32 ; Operatin

0-C     D-L     M-R     S-Z