|
Details, datasheet, quote on part number:IDT74FCT244CTPY
| |
Datasheet text preview:
IDT54/74FCT244T/AT/CT FAST CMOS OCTAL BUFFER/LINE DRIVER
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
FAST CMOS OCTAL BUFFER/LINE DRIVER
FEATURES:
· · · ·
IDT54/74FCT244T/AT/CT
· · · · ·
Std., A, and C grades Low input and output leakage 1µA (max.) CMOS power levels True TTL input and output compatibility: VOH = 3.3V (typ.) VOL = 0.3V (typ.) High Drive outputs (-15mA IOH, 64mA IOL) Meets or exceeds JEDEC standard 18 specifications Military product compliant to MIL-STD-883, Class B and DESC listed (dual marked) Power off disable outputs permit "live insertion" Available in the following packages: Industrial: SOIC, SSOP, QSOP, TSSOP Military: CERDIP, LCC
DESCRIPTION:
The IDT octal buffer/line driver is built using an advanced dual metal CMOS technology. The FCT244T is designed to be employed as a memory and address driver, clock driver, and bus-oriented transmitter/ receiver which provides improved board density.
FUNCTIONAL BLOCK DIAGRAM
OEA OEB DA0 OB0 DA1 OB1 DA2 OB2 DA3 OB3 OA0 DB0 OA1 DB1 OA2 DB2 OA3 DB3
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
1
JUNE 2002
DSC-5586/2
© 2002 Integrated Device Technology, Inc.
IDT54/74FCT244T/AT/CT FAST CMOS OCTAL BUFFER/LINE DRIVER
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATION
OEA OB0 DA0 OEB VCC
INDEX OEA DA0 OB0 DA1 OB1 DA2 OB2 DA3 OB3 GND 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VCC OE B OA0 DB0 OA1 DB1 OA2 DB2 OA3 DB3
32 DA1 OB1 DA2 OB2 DA3 4 5 6 7 8
20 19 18 1 17 16 15
OA0 DB0 OA1 DB1 OA2
14 9 10 11 12 13
GND DB3 OB3 DB2
CERDIP/ SOIC/ SSOP/ QSOP/ TSSOP TOP VIEW
LCC TOP VIEW
ABSOLUTE MAXIMUM RATINGS(1)
Symbol Description Max 0.5 to +7 0.5 to VCC+0.5 65 to +150 60 to +120 Unit V V °C mA VTERM(2) Terminal Voltage with Respect to GND VTERM(3) Terminal Voltage with Respect to GND TSTG IOUT Storage Temperature DC Output Current
PIN DESCRIPTION
Pin Names OEA, OEB Dxx Oxx Inputs Outputs Description 3-State Output Enable Inputs (Active LOW)
NOTES: 1 . Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. No terminal voltage may exceed Vcc by +0.5V unless otherwise noted. 2 . Inputs and Vcc terminals only. 3 . Output and I/O terminals only.
FUNCTION TABLE(1)
OEA L L H Inputs OEB L L H D L H X Outputs L H Z
CAPACITANCE (TA = +25°C, F = 1.0MHz)
Symbol CI N COUT Parameter(1) Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Typ. 6 8 Max. 10 12 Unit pF pF
NOTE: 1 . H = HIGH Voltage Level X = Don't Care L = LOW Voltage Level Z = High Impedance
NOTE: 1 . This parameter is measured at characterization but not tested.
2
OA3
IDT54/74FCT244T/AT/CT FAST CMOS OCTAL BUFFER/LINE DRIVER
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified: Industrial: TA = 40°C to +85°C, VCC = 5.0V ±5%; Military: TA = 55°C to +125°C, VCC = 5.0V ±10%
Symbol VIH VIL IIH IIL IOZH IOZL II VIK VH ICC Parameter Input HIGH Level Input LOW Level Input HIGH Current(4) Input LOW Current(4) High Impedance Output Current (3-State output pins)(4) Input HIGH Current(4) Clamp Diode Voltage Input Hysteresis Quiescent Power Supply Current VCC = Max., VI = VCC (Max.) VCC = Min, IIN = -18mA -- VCC = Max., VIN = GND or VCC Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max. VCC = Max. VCC = Max VI = 2.7V VI = 0.5V VO = 2.7V VO = 0.5V Min. 2 -- -- -- -- -- -- -- -- -- Typ.(2) -- -- -- -- -- -- -- 0.7 200 0.01 Max. -- 0.8 ±1 ±1 ±1 ±1 ±1 1.2 -- 1 µA V mV mA Unit V V µA µA µA
OUTPUT DRIVE CHARACTERISTICS
Symbol VOH Parameter Output HIGH Voltage Test Conditions(1) VCC = Min IOH = 6mA MIL VIN = VIH or VIL IOH = 8mA IND IOH = 12mA MIL IOH = 15mA IND VCC = Min IOL = 48mA MIL VIN = VIH or VIL IOL = 64mA IND VCC = Max., VO = GND(3) Min. 2.4 2 -- 60 Typ.(2) 3.3 3 0.3 120 Max. -- -- 0.55 225 V mA Unit V
VOL IOS
Output LOW Voltage Short Circuit Current
NOTES: 1 . For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2 . Typical values are at VCC = 5.0V, +25°C ambient. 3 . Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4 . The test limit for this parameter is ±5µA at TA = 55°C.
3
IDT54/74FCT244T/AT/CT FAST CMOS OCTAL BUFFER/LINE DRIVER
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
POWER SUPPLY CHARACTERISTICS
Symbol ICC ICCD Parameter Quiescent Power Supply Current TTL Inputs HIGH Dynamic Power Supply Current(4) VCC = Max. VIN = 3.4V(3) VCC = Max. Outputs Open OEA = OEB = GND One Input Toggling 50% Duty Cycle VCC = Max. Outputs Open fi = 10MHz 50% Duty Cycle OEA = OEB = GND One Bit Toggling VCC = Max. Outputs Open fi = 2.5MHz 50% Duty Cycle OEA = OEB = GND Eight Bits Toggling VIN = VCC VIN = GND Test Conditions(1) Min. -- -- Typ.(2) 0.5 0.15 Max. 2 0.25 Unit mA mA/ MHz
IC
Total Power Supply Current(6)
VIN = VCC VIN = GND VIN = 3.4V VIN = GND VIN = VCC VIN = GND VIN = 3.4V VIN = GND
--
1.5
3.5
mA
--
1.8
4.5
--
3
6(5)
--
5
14(5)
NOTES: 1 . For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2 . Typical values are at VCC = 5.0V, +25°C ambient. 3 . Per TTL driven input; (VIN = 3.4V). All other inputs at VCC or GND. 4 . This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5 . Values for these conditions are examples of ICC formula. These limits are guaranteed but not tested. 6 . IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ICC DHNT + ICCD (fCP/2+ fiNi) ICC = Quiescent Current ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) fi = Output Frequency Ni = Number of Outputs at fi All currents are in milliamps and all frequencies are in megahertz.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Propagation Delay Dx to Ox Output Enable Time Output Disable Time Condition(1) CL = 50pF RL = 500 54FCT244T Mil. Min.(2) Max. 1.5 7 1.5 1.5 8.5 7.5 54/74FCT244AT Ind. Mil. Min.(2) Max. Min.(2) Max. 1.5 4.8 1.5 5.1 1.5 1.5 6.2 5.6 1.5 1.5 6.5 5.9 54/74FCT244CT Ind. Mil. Min.(2) Max. Min.(2) Max. 1.5 4.1 1.5 4.6 1.5 1.5 5.8 5.2 1.5 1.5 6.5 5.7 Unit ns ns ns
NOTES: 1 . See test circuit and waveforms. 2 . Minimum limits are guaranteed but not tested on Propagation Delays.
4
IDT54/74FCT244T/AT/CT FAST CMOS OCTAL BUFFER/LINE DRIVER
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
TEST CIRCUITS AND WAVEFORMS
V CC 500 VIN Pulse Generator RT D.U.T . V O UT 7.0V
SWITCH POSITION
Test Open Drain Disable Low Enable Low All Other Tests Switch Closed Open
50pF CL
500
DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
Octal link
Test Circuits for All Outputs
DATA INPUT TIMING INPUT ASYNCHRONOUS CONTROL PRESET CLEAR ETC. SYNCHRONOUS CONTROL PRESET CLEAR CLOCK ENABLE ETC.
tSU
tH
tREM
3V 1.5V 0V 3V 1.5V 0V 3V 1.5V 0V 3V 1.5V 0V
Octal link
LOW-HIGH-LOW PULSE tW HIGH-LOW-HIGH PULSE
Octal link
1.5V
1.5V
tSU
tH
Pulse Width
Set-Up, Hold, and Release Times
ENABLE SAME PHASE INPUT TRANSITION tPLH OUTPUT tPLH OPPOSITE PHASE INPUT TRANSITION tPHL tPHL 3V 1.5V 0V VOH 1.5V V OL 3V 1.5V 0V
Octal link
DISABLE 3V 1.5V
CONTROL INPUT t PZL OUTPUT NORMALLY LOW OUTPUT NORMALLY HIGH SWITCH CLOSED tPZH SWITCH OPEN 3.5V 1.5V tPHZ 0.3V 1.5V 0V tP L Z
0V 3.5V 0.3V V OL VOH 0V
Octal link
Propagation Delay
Enable and Disable Times
NOTES: 1 . Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. 2 . Pulse Generator for All Pulses: Rate 1.0MHz; tF 2.5ns; tR 2.5ns.
5
|
|
