|
|
Part: EL7154
Category:
Description: Driver, Tr-state Ate Pin, 4A Peak, 10MHz, 4.5-16v
Company: Intersil Corporation
Datasheet: Download EL7154 datasheet File size : 84 kB
Request For quote: Find where to buy EL7154
Datasheet text preview:
®
EL7154
D a ta Sheet Ja nu ar y 1996, Rev B FN7278
High Speed, Monolithic Pin Driver
The EL7154 3-state pin driver is particularly well suited for ATE and level shifting applications. The 4A peak drive capability, makes the EL7154 an excellent choice when driving high speed capacitive lines. The p-channel MOSFET is completely isolated from the power supply, providing a high degree of flexibility. Pin (7) can be grounded, and the output can be taken from pin (8) when a "source follower" output is desired. Then n-channel MOSFET has an isolated drain, but shares a common bus with pre-drivers and level shifter circuits. This is necessary to ensure that the nchannel device can turn off effectively when VL goes below GND. In some power-FET and IGBT applications, negative drive is desirable to insure effective turn-off. The EL7154 can be used in these applications by returning VL to a moderate negative potential.
Features
· Comparatively low cost · 3-State output · 3V and 5V Input compatible · Clocking speeds up to 10MHz · 20ns Switching/delay time · 4A Peak drive · Isolated drains · Low output impedance--2.5 · Low quiescent current--5mA · Wide operating voltage--4.5V16V · Isolated P-channel device · Separate ground and VL pins
Pinout
EL7154 (8-PIN PDIP, SOIC) TOP VIEW
Applications
· Loaded circuit board testers · Digital testers · Level shifting below GND · IGBT drivers · CCD drivers
Ordering Information
PART NUMBER EL715 4CN EL715 4CS TEMP. RANGE -40°C to +85°C -40°C to +85°C P ACKAGE 8-Pin PDIP 8-Pin SOIC PKG. NO. MDP003 1 MDP002 7
Nominal Operating Voltage Range
PIN VL VDDVL M IN -3 5 2 -0.5 5 MAX 0 15 15 15 15
Truth Table
3-STATE 0 0 1 1 INPUT 0 1 0 1 POUT Open Open HIGH Open NOUT Open Open Open LOW
V H V L VDDVH VDD
Manufactured under U.S. Patent Nos. 5,334,883, #5,341,047, #5,352,578, #5,352,389, #5,351,012, #5,374,898
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners.
EL7154
Absolute Maximum Ratings (TA = 25°C)
Supply (VDD to VL; VHVL, VH to GND), V+ to VH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V VL to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5V Input Pins . . . . . . . . . . . . . . . . . -0.3V below VL to +0.3V above VDD Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4A Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C Power Dissipation SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .570mW PDIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1050mW
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
PARAMETER INPUT VIH IIH VIL IIL VHVS OUTPUT ROH ROL IOUT IPK IDC POWER SUPPLY IS VS IG IH
TA = 25°C, VDD = +12V, VH = +12V, VL = -3V, unless otherwise specified DESCRIPTION TEST CONDITIONS M IN TYP M AX UNITS
Logic "1" Input Voltage Logic "1" Input Current Logic "0" Input Voltage Logic "0" Input Current Input Hysteresis VIL = 0V VIH = VDD
2.4 0.1 10 0.6 0.1 0.3 10
V µA V µA V
Pull-Up Resistance Pull-Down Resistance Output Leakage Current Peak Output Current Continuous Output Current
IOUT = -100mA IOUT = +100mA VDD/GND Source Sink Source/Sink 200
1. 5 2 0.2 4.0 4.0
4 4 10
µA A mA
Power Supply Current Operating Voltage Current to GND (Pin 4) Off Leakage at VH
Inputs = VDD 4.5
1
2 .5 16
mA V µA µA
1 Pin 8 = 0V 1
10 10
AC Electrical Specifications
PARAMET ER
TA = 25°C unless otherwise specified D E S C R IP T I O N TEST CONDITIONS MIN TYP MAX UNITS
SWITCHING CHARACTERISTICS (VDD = VH = 12V; VL = -3V) tR Rise Time CL = 100pF CL = 2000pF tF Fall Time CL = 100pF CL = 2000pF tD-1 tD-2 tD-1 tD-2 Turn-Off Delay Time Turn-On Delay Time 3-State Delay 3-State Delay CL = 2000pF CL = 2000pF 4 20 4 20 20 10 25 25 25 25 ns ns ns ns 25 ns 25 ns
2
EL7154 Timing Table
Standard Test Configuration
3
EL7154 Typical Performance Curves
Max Power/Derating Curves Switch Threshold vs Supply Voltage
Input Current vs Voltage
Peak Drive vs Supply Voltage
Quiescent Supply Current
"ON" Resistance vs Supply Voltage
Average Supply Current vs Voltage and Frequency
Rise/Fall Time vs Load
4
EL7154 Typical Applications
Pin Driver Adjustable Amplitude Pulse Generator
IGBT Driver (with Negative Swing)
PMOS Follower
Resonant Gate Driver
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 5
Others parts begin by el
EL-1 EL-2 EL-3 EL-4 EL-5 EL-6 EL-7 EL-8 EL-9 EL-10 EL-11 EL-12 EL-13 EL-14 EL-15 EL-16 EL-17 EL-18
|
|
|
