Details, datasheet, quote on part number: HA2-2510/883
CategoryAnalog & Mixed-Signal Processing => Amplifiers => Operational Amplifiers
DescriptionHigh Slew Rate Operational Amplifier
CompanyIntersil Corporation
DatasheetDownload HA2-2510/883 datasheet
Cross ref.Similar parts: OP42AJ/883C, AD518JH/+, AD518JH, AD518KH/+, AD518KH, AD518SH/883B, AD518SH, OP42AJ/883C, AM-450-2, AM-450-2M
Find where to buy


Features, Applications


The is a high performance operational amplifier which sets the standards for maximum slew rate and wide bandwidth operation in moderately powered, internally compensated, monolithic devices. In addition to excellent dynamic characteristics, this dielectrically isolated amplifier also offers low offset current and high input impedance. The 50V/s minimum slew rate and fast settling time of the HA-2510/883 are ideally suited for high speed D/A, A/D, and pulse amplification designs. The HA-2510/883's superior bandwidth and 750kHz minimum full power bandwidth are extremely useful in RF and video applications. To insure compliance with slew rate and transient response specifications, all devices are 100% tested for AC performance characteristics over full temperature limits. To improve signal conditioning accuracy, the HA-2510/883 provides a maximum offset current of 25nA and a minimum input impedance of 50M, both 25oC, as well as offset voltage adjust capability.


This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. High Slew Rate.50V/s (Min) 65V/s (Typ) Wide Power Bandwidth. 750kHz (Min) Low Offset Current. 25nA (Min) 10nA (Typ) High Input Impedance. 50M (Min) 100M (Typ) Wide Small Signal Bandwidth. 12MHz (Typ) Fast Settling Time of 10V Step). 250ns (Typ) Low Quiescent Supply Current. 6mA (Max) Internally Compensated For Unity Gain Stability

Data Acquisition Systems RF Amplifiers Video Amplifiers Signal Generators Pulse Amplification

PART NUMBER HA2-2510/883 HA7-2510/883 TEMP. RANGE (oC) to 125 PACKAGE 8 Pin Can 8 Ld CERDIP PKG. NO. T8.C F8.3A

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2002. All Rights Reserved

Voltage Between V+ and V- Terminals. 40V Differential Input Voltage. 15V Voltage at Either Input Terminal. V+ to VPeak Output Current. 50mA ESD Rating. <2000V

Thermal Resistance (Typical, Note JA JC CERDIP Package. 120oC/W 30oC/W Metal Can Package. 160oC/W 75oC/W Package Power Dissipation Limit at 75oC for TJ 175oC CERDIP Package. 870mW Metal Can Package. 625mW Package Power Dissipation Derating Factor Above 75oC CERDIP Package. 8.7mW/oC Metal Can Package. 6.3mW/oC Maximum Junction Temperature. 175oC Maximum Storage Temperature Range. to 150oC Maximum Lead Temperature (Soldering 10s). 300oC

CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTE: JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief

TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = 15V, RSOURCE 100 , RLOAD 500k , VOUT = 0V, Unless Otherwise Specified. PARAMETER Input Offset Voltage SYMBOL VIO VCM = 0V CONDITIONS GROUP A SUBGROUPS 2, 3 Input Bias Current +IB VCM = 0V, +RS = 100k, -RS -IB VCM = 0V, +RS = 100, -RS 2, 3 Input Offset Current IIO VCM = 0V, +RS = 100k, -RS 2, 3 Common Mode Range +CMR 2, 3 -CMR 2, 3 Large Signal Voltage Gain +AVOL VOUT = 0V and 5, 6 -AVOL VOUT = 0V and 5, 6 Common Mode Rejection Ratio +CMRR VCM = -25V, VOUT = -10V VCM = -5V, VOUT = +10V TEMP (oC) MIN MAX UNITS mV nA kV/V dB

TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = 15V, RSOURCE 100 , RLOAD 500k , VOUT = 0V, Unless Otherwise Specified. PARAMETER Output Voltage Swing SYMBOL +VOUT = 2k CONDITIONS GROUP A SUBGROUPS 5, 6 -VOUT 5, 6 Output Current +IOUT VOUT 5, 6 -IOUT VOUT 5, 6 Quiescent Power Supply Current +ICC VOUT = 0V, IOUT = 0mA VOUT = 0V, IOUT = 0mA VSUP = -15V VSUP = -10V -PSRR 2, 3 Offset Voltage Adjustment +VIOAdj Note -VIOAdj Note NOTE: 2. Offset adjustment range is [VIO (Measured) 1mV] minimum referred to output. This test is for functionality only to assure adjustment through 0V. TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = 15V, RSOURCE 50 , RLOAD 2k , CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified. PARAMETER Slew Rate SYMBOL +SR CONDITIONS VOUT +5V, 25% +SR 75% GROUP A SUBGROUPS 8A, 8B -SR VOUT -5V, 75% -SR 8A, 8B TEMP (oC) MIN MAX UNITS V/ s TEMP (oC) MIN VIO-1 VIO+1 MAX UNITS dB mV


Related products with the same datasheet
Some Part number from the same manufacture Intersil Corporation
HA2-2520-2 20MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers
HA2-2520/883 Uncompensated, High Slew Rate Operational Amplifier
HA2-2522-2 20MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers
HA2-2600-2 12MHz, High Input Impedance Operational Amplifiers
HA2-2602/883 Wideband, High Impedance Operational Amplifiers
HA2-2605-5 12MHz, High Input Impedance Operational Amplifiers
HA2-2620-2 100MHz, High Input Impedance, Very Wideband, Uncompensated Operational Amplifiers
HA2-2640-2 4MHz, High Supply Voltage Operational Amplifiers
HA2-5002-2 110MHz, High Slew Rate, High Output Current Buffer
HA2-5002/883 Monolithic, Wideband, High Slew Rate, High Output Current Buffer
HA2-5033-2 250MHz Video Buffer
HA2-5112/883 Dual, Low Noise, High Performance Uncompensated Operational Amplifier
HA2-5127/883 8.5MHz, Ultra-low Noise Precision Operational Amplifier
HA2-5135/883 Precision Operational Amplifier
HA2-5137883 60mhz, Ultra Low Noise, Precision Operational Amplifier
HA2-5160-2 100MHz, JFET Input, High Slew Rate, Uncompensated, Operational Amplifiers
HA2-5170-5 8mhz, Precision, JFET Input Operational Amplifier
HA2-5177883 Ultra Low Offset Voltage Operational Amplifier

HI-548/883 : Analog Switch, Spst, Dual, Nclosed, Ron = 55, TTL Inputs, 80mA Signal Current, CMOS, 883 Compliant

HS9-6664RH-T : 64K Radiation Hardened 8K X 8 CMOS Prom

IH5020C :

ISL84542IH-T : Low-Voltage, Single Supply, Dual Spst, SPDT Analog Switches

ISL9000AIRBBZ : Dual LDO with Low Noise, Very High Psrr, and Low IQ

ISL6506BCBZ : Multiple Linear Power Controller with ACPI Control Interface

ISL9011IRRKZ : Dual LDO with Low Noise, Low IQ, and High PSRR

ISL9104AIRUWZ-T7A : 500mA 4.3MHz Low IQ High Efficiency Synchronous Buck Converter The ISL9104, ISL9104A is a 500mA, 4.3MHz step-down regulator, which is ideal for powering low-voltage microprocessors in compact devices such as PDAs and cellular phones. It is optimized for generating low output voltages down to 0.8V.

EL5371IUZ-T7 : LINE DRIVER Specifications: Device Type: Line / Bus Driver

0-C     D-L     M-R     S-Z