Details, datasheet, quote on part number: HA3-2539-5
CategoryAnalog & Mixed-Signal Processing => Amplifiers => High Speed/Video Amplifiers => Voltage Feedback
Description600MHz, Very High Slew Rate Operational Amplifier
CompanyIntersil Corporation
DatasheetDownload HA3-2539-5 datasheet
Find where to buy


Features, Applications

600MHz, Very High Slew Rate Operational Amplifier

The Intersil HA-2539 represents the ultimate in high slew rate, wideband, monolithic operational amplifiers. It has been designed and constructed with the Intersil High Frequency Bipolar Dielectric Isolation process and features dynamic parameters never before available from a truly differential device. With a 600V/s slew rate and a 600MHz gain bandwidth product, the HA-2539 is ideally suited for use in video and RF amplifier designs, in closed loop gains 10 or greater. Full 10V swing coupled with outstanding AC parameters and complemented by high open loop gain makes the devices useful in high speed data acquisition systems. For further design assistance please refer to Application Note AN541 (Using the HA-2539 Very High Slew Rate Wideband Operational Amplifiers) and Application Note AN556 (Thermal Safe-Operating-Areas For High Current Operational Amplifiers. For military grade product information, the HA-2539/883 data sheet is available upon request.


Very High Slew Rate. 600V/s Open Loop Gain. 15kV/V Wide Gain-Bandwidth (AV 10). 600MHz Power Bandwidth. 9.5MHz Low Offset Voltage. 8mV Input Voltage Noise. 6nV/Hz Output Voltage Swing. 10V Monolithic Bipolar Dielectric Construction

Pulse and Video Amplifiers Wideband Amplifiers High Speed Sample-Hold Circuits RF Oscillators

NOTE: No-Connection (NC) leads may be tied to a ground plane for better isolation and heat dissipation.

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2003. All Rights Reserved All other trademarks mentioned are the property of their respective owners.

Supply Voltage Between V+ and V- Terminals. 35V Differential Input Voltage. 6V Peak Output Current. 50mA Continuous Output Current. 33mARMS

Thermal Resistance (Typical, Note 2) JA (oC/W) JC (oC/W) PDIP Package. 95 N/A Maximum Internal Quiescent Power Dissipation (Note 1) Maximum Junction Temperature (Plastic Package).150oC Maximum Storage Temperature Range. to 150oC Maximum Lead Temperature (Soldering 10s). 300oC

CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES: 1. Maximum power dissipation with load conditions must be designed to maintain the maximum junction temperature below 150oC for the plastic package. By using Application Note AN556 on Safe Operating Area equations, along with the thermal resistances, proper load conditions can be determined. Heat sinking is recommended above JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

VSUPPLY < 10pF, Unless Otherwise Specified TEMP. (oC)
Average Offset Voltage Drift Bias Current

Input Resistance Input Capacitance Common Mode Range Input Current Noise = 1kHz, RSOURCE = 0) Input Voltage Noise = 1kHz, RSOURCE = 0) TRANSFER CHARACTERISTICS Large Signal Voltage Gain (Note 3) Common Mode Rejection Ratio (Note 4) Minimum Stable Gain Bandwidth (Notes 5, 6)

VSUPPLY < 10pF, Unless Otherwise Specified (Continued) TEMP. (oC)

PARAMETER OUTPUT CHARACTERISTICS Output Voltage Swing (Notes 3, 10) Output Current (Note 3) Output Resistance Full Power Bandwidth (Notes 3, 7) TRANSIENT RESPONSE (Note 8) Rise Time Overshoot Slew Rate Settling Time: 10V Step to 0.1% POWER REQUIREMENTS Supply Current Power Supply Rejection Ratio (Note 9) NOTES: 10V. 4. VCM = 10.

Slew Rate 7. Full Power Bandwidth guaranteed based on slew rate measurement using: FPBW ---------------------------2 V PEAK 8. Refer to Test Circuits section of data sheet. 9. VSUPPLY +5V, -15V and +15V, -5V.

10. Guaranteed range for output voltage is 10V. Functional operation outside of this range is not guaranteed.


Related products with the same datasheet
Some Part number from the same manufacture Intersil Corporation
HA3-2540-5 400MHz, Fast Settling Operational Amplifier
HA3-2544C-5 50MHz, Video Operational Amplifier
HA3-2546-5 30MHz, Voltage Output, Two Quadrant Analog Multiplier
HA3-2556-9 57MHz, Wideband, Four Quadrant, Voltage Output Analog Multiplier
HA3-2605-5 12MHz, High Input Impedance Operational Amplifiers
HA3-2625-5 100MHz, High Input Impedance, Very Wideband, Uncompensated Operational Amplifiers
HA3-2839-5 600mhz, Very High Slew Rate Operational Amplifier
HA3-2842-5 80MHz, High Slew Rate, High Output Current, Video Operational Amplifier
HA3-4741-5 Quad, 3.5MHz, Operational Amplifier
HA3-4905-5 Precision Quad Comparators
HA3-5002-5 110MHz, High Slew Rate, High Output Current Buffer
HA3-5020-5 100MHz Current Feedback Video Amplifier With Disable
HA3-5033-5 250MHz Video Buffer
HA3-5102-5 Dual And Quad, 8MHz And 60MHz, Low Noise Operational Amplifiers
HA3-5114-5 Dual And Quad, 8mhz And 60mhz, Low Noise Operational Amplifiers
HA3-5142-5 Dual, 400kHz, Ultra-low Power Operational Amplifier
HA3-5320-5 Microsecond Precision Sample And Hold Amplifier Amplifier
HA3-5330-5 650ns Precision Sample And Hold Amplifier

DG441/883 : Monolithic Quad SPST CMOS Analog Switches

EL1511CS-T13 : Driver, Vco DMT Adsl, Differential Line, Medium Power, 360mA Driver, Power Control, Dual

HFA1412/883 : Quad, High Speed, Low Power, Video Closed Loop Buffer

ISL6841IB : Improved Industry Standard Single-ended Current Mode PWM Controller. UVLO=7.0 V; Dmax=100%The ISL6840, ISL6841, ISL6842, ISL6843, ISL6844, ISL6845 Family of Adjustable Frequency, Low Power, Pulse Width Modulating (PWM) Current Mode Controllers is Designed For a Wide Range of Power Conversion A

ISL55191IBZ : The ISL55191 and ISL55291 are single and dual high speed operational amplifiers featuring low noise, low distortion, and rail-to-rail output drive capability. They are designed to operate with single and dual supplies from +5VDC (2.5VDC) down to +3VDC (1.5VDC). These amplifiers draw 6.1mA of quies

EL5327CRZ : 2.5mhz 4, 8, 10 & 12 Channel Rail-to-rail Buffers

ISL9112IRT7Z-T7A : 1.2A High Efficiency Buck-Boost Regulators The ISL9110 and ISL9112 are highly-integrated Buck-Boost switching regulators that accept input voltages either above or below the regulated output voltage. Unlike other Buck-Boost regulators, these regulators automatically transition between operating mod

ISL95837HRZ : 3+1 And 1+1 Voltage Regulator For IMVP-7/VR12 CPUs Compliant with IMVP-7/VR12, the ISL95835 provides a complete solution for microprocessor and graphic processor core power supply. It provides two Voltage Regulators (VRs) with three integrated gate drivers. The first VR can be configured as 3-,

ISL65426IRZA-TS2715 : The ISL65426 is a high efficiency dual output monolithic synchronous buck converter operating over an input voltage range of 2.375V to 5.5V. This single chip power solution provides two output voltages which are selectable or externally adjustable from 1V to 80% of the supply voltage while deliverin

EL1848IYZ-T13 : Pmic - Led Driver Integrated Circuit (ics) Backlight Yes -; IC LED DRIVR WHITE BCKLGT 8-MSOP Specifications: Type - Primary: Backlight ; Type - Secondary: White LED ; Number of Outputs: 1 ; Constant Current: Yes ; Constant Voltage: - ; Topology: PWM, Step-Up (Boost) ; Frequency: 800kHz ~ 1.2MHz ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

ISL28127FUZ-T13 : Linear - Amplifier - Instrumentation, Op Amps, Buffer Amp Integrated Circuit (ics) General Purpose Tape & Reel (TR) 2.2mA 4.5 V ~ 40 V, 2.25 V ~ 20 V; IC OPAMP .10MHZ PREC LN 8MSOP Specifications: Packaging: Tape & Reel (TR) ; Amplifier Type: General Purpose ; Number of Circuits: 1 ; Package / Case: 8-TSSOP, 8-MSOP (0.118", 3.00mm Width) ; Slew Rate: 3.6 V/s ; Gain Bandwidth Product: 10MHz ; Current - Supply: 2.2mA ; Current - Output / Channel: 45mA ; Voltage - Supply, Si

0-C     D-L     M-R     S-Z