Details, datasheet, quote on part number: HA4-5020/883
Description100mhz Current Feedback Video Amplifier with Disable
CompanyIntersil Corporation
DatasheetDownload HA4-5020/883 datasheet
Find where to buy


Features, Applications

100MHz Current Feedback Video Amplifier with Disable

The is a wide bandwidth, high slew rate amplifier optimized for video applications and gains between 1 and 10. Manufactured on Intersil's Reduced Feature Complementary Bipolar DI process, this amplifier uses current mode feedback to maintain higher bandwidth at a given gain than conventional voltage feedback amplifiers. Since is a closed loop device, the HA-5020/883 offers better gain accuracy and lower distortion than open loop buffers. The HA-5020/883 features low differential gain and phase and will drive two double terminated 75 coax cables to video levels with low distortion. Adding a gain flatness performance of 0.1dB makes this amplifier ideal for demanding video applications. The bandwidth and slew rate of the HA-5020/ 883 are relatively independent of closed loop gain. The 105MHz unity gain bandwidth only decreases at a gain of 10. The HA-5020/883 used in place of a conventional op amp will yield a significant improvement in the speed power product. To further reduce power, the HA-5020/883 has a disable function which significantly reduces supply current, while forcing the output to a true high impedance state. This allows the outputs of multiple amplifiers to be wire-OR'd into multiplexer configurations. The device also includes output short circuit protection and output offset voltage adjustment. The HA-5020/883 offers significant enhancements over competing amplifiers, such as the EL2020. Improvements include unity gain bandwidth, slew rate, video performance, lower supply current, and superior DC specifications.


This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. Wide Unity Gain Bandwidth. 105MHz (Min) Slew Rate. 800V/s Output Current. 30mA (Min) Drives 3.5V into 75 Differential Gain. 0.025% Differential Phase.0.025 Deg Low Input Noise Voltage. 4.5nV/Hz Low Supply Current. 10mA (Max) Wide Supply Range. to 15V Output Enable/Disable High Performance Replacement for EL2020/883


Unity Gain Video/Wideband Buffer Video Gain Block Video Distribution Amp/Coax Cable Driver Flash A/D Driver Waveform Generator Output Driver Current to Voltage Converter; D/A Output Buffer Radar Systems Imaging Systems

PART NUMBER HA7-5020/883 HA4-5020/883 TEMPERATURE RANGE to +125oC PACKAGE 8 Lead CerDIP 20 Lead Ceramic LCC

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 321-724-7143 | Copyright Intersil Corporation 1999

Voltage Between V+ and V- Terminals. 36V Differential Input Voltage. 8V Voltage at Either Input Terminal. V+ to VPeak Output Current. Full Short Circuit Protected Junction Temperature (TJ). +175oC Storage Temperature Range. to +150oC ESD Rating. < 2000V Lead Temperature (Soldering 10s). +300oC

Thermal Package Characteristics JA JC CerDIP Package. 115oC/W 30oC/W Ceramic LCC Package. 75oC/W 23oC/W Package Power Dissipation Limit at +75oC for TJ +175oC CerDIP Package. 0.87W Ceramic LCC Package. 1.33W Package Power Dissipation Derating Factor Above +75oC CerDIP Package. 8.7mW/oC Ceramic LCC Package. 13.3mW/oC

CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

Operating Temperature Range. to +125oC Operating Supply Voltage. to 15V VINCM 1/2(V+ - V-) = 1k VDISABLE or 0V

TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: Supply Voltage = 15V, RSOURCE = 0, AVCL = 1k, RLOAD = 400, VOUT = 0V, VDISABLE = V+, Unless Otherwise Specified. GROUP A SUBGROUP 2, 3 Common Mode Rejection Ratio +CMRR VCM = -25V VCM = -5V VSUP = -15V VSUP = -18V VCM = 0V VCM = -25V VCM = -5V Calculated 1/IBPCMP IBPCMP IBPPSP VSUP = -15V VSUP = -18V VCM = 0V LIMITS TEMPERATURE +125oC, -55oC MIN o

Non-Inverting (+IN) Current +IN Common Mode Rejection
Non-Inverting (+IN) Input Impedance +IN Power Supply Rejection

TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: Supply Voltage = 15V, RSOURCE = 0, AVCL = 1k, RLOAD = 400, VOUT = 0V, VDISABLE = V+, Unless Otherwise Specified. GROUP A SUBGROUP -CMR 2, 3 Transimpedance = 400, VOUT = 400, VOUT to -10V VIN = 12.8V -VOUT VIN = -5V, VIN = -5V, VIN = -3V Note -IOUT Note Short Circuit Output Current +ISC RL = Open, VIN 2, 3 -ISC RL = Open, VIN 2, 3 Disabled Output Current +ILEAK VIN = 0V, VOUT RL = Open, VDIS = 0V VIN = 2V -ILEAK VIN = 0V, VOUT RL = Open, VDIS = 0V VIN = -2V LIMITS TEMPERATURE +125oC, -55oC MIN o


Some Part number from the same manufacture Intersil Corporation
ISL6210 Dual Synchronous Rectified Mosfet Drivers
ISL5585AIMZ 3.3V Ringing SLIC Family for Voice Over Broadband (vob)
ISL22346WMVEP Low Noise, Low Power I2c Bus, 128 Taps
EL2210 Low Cost, Dual, Triple and Quad Video Op Amps
ZL2005ALNFT Digital-dc Integrated Power Management and Conversion IC
HSP9501_04 Programmable Data Buffer
HA1-5340/883 High Speed, Low Distortion, Precision Monolithic Sample and Hold Amplifier
HFA1102EVAL 600mhz Current Feedback Amplifier with Compensation Pin
ISL6268 High-performance Notebook PWM Controller
ISL5957IAZ 14-bit, +3.3v, 260+msps, High Speed D/A Converter
HS-139RH_04 Radiation Hardened Quad Voltage Comparator
EL6839CLZT13 Dual 4-channel Driver with Oscillator and LVDS
X5328P-2.7A CPU Supervisor with 32kbit SPI Eeprom
HI-883 The Hi-200/883 is a Monolithic Device Comprising two Independently Selectable SPST Switchers Which Feature fast Switching Speeds
IH5151MJE Dual Spdt, CMOS Analog Switch
ISL23710 Terminal Voltage +- 3V or +- 5V, 128 Taps IC Serial Interface
X9269TV24I Dual Digitally-controlled Potentiometers
ISL6406CBZ Single Synchronous Buck Pulse-width Modulation (pwm) Controller
CD4068 CMOS 8 Input Nand/and Gate
IM5600 256 Bit Bipolar Read Only Memory
ISL8601 Single-phase, Pmbus-enabled PWM Controller with Integrated FET Drivers

5962R9581301TCC : Radiation Hardened CMOS Dual SPDT Analog Switch

HI1171JCB-T : 8-Bit, 40 Msps, High Speed D/A Converter

ISL22414WFU10Z : Single Digitally Controlled Potentiometer (XDCP), Low Noise, Low Power, I2C Bus, 256 Taps The ISL22414 integrates a single digitally controlled potentiometer (DCP), control logic and non-volatile memory on a monolithic CMOS integrated circuit.

ISL54063 : 1.8V to +6.5v, High Off-isolation, Dual SPST Analog Switch

ICL232_05 : +5V Powered, Dual Rs-232 Transmitter/receiver

ISL60002BIH325Z-TK : Precision 2.50v, 1.08u-watt, High Precision FGA Voltage References

X5329PI-4.5A : CPU Supervisor with 32kbit SPI Eeprom

X5001S8I : CPU Supervisor

X5325S8ZT1 : Pmic - Supervisor Integrated Circuit (ics) Simple Reset/Power-On Reset Tape & Reel (TR) 1; IC CPU SUPERV 32K EE 8-SOIC Specifications: Output: Open Drain or Open Collector ; Reset: Active High ; Package / Case: 8-SOIC (0.154", 3.90mm Width) ; Packaging: Tape & Reel (TR) ; Number of Voltages Monitored: 1 ; Reset Timeout: 100 ms Minimum ; Type: Simple Reset/Power-On Reset ; Voltage - Threshold: 4.38V ; Operating T

ISL88031IU8HAZ-TK : Quintuple Voltage Monitor

ISL32602EFUZ-T : 1.8V To 3.3V, Micro-Power, 15kV ESD, +125C, Slew Rate Limited, RS-485/RS-422 Transceivers The Intersil ISL32600E, ISL32601E, ISL32602E and ISL32603E are 15kV IEC61000 ESD protected, micro power, wide supply range transceivers for differential communication. The ISL32600E and ISL32601E operate wi

Same catergory


GS9007A : Video Transport. Quad Serial Digital Cable Driver. DATA SHEET two output pairs (four outputs total) meeting SMPTE 259M nominal 550 ps rise and fall times accepts SMPTE and standard ECL input levels operates from a single or -5 volt supply on-chip DC restoration for low jitter 250mW power dissipation APPLICATIONS 4SC, 4:2:2 and 360Mb/s Serial Digital Interfaces. The is a bipolar intergrated circuit designed.

TPS60120 : Regulated 200-ma High Efficiency Charge Pump DC/DC Converters. TPS60124, TPS60125 REGULATED 200-mA HIGH EFFICIENCY CHARGE PUMP DC/DC CONVERTERS applications High Average Efficiency Over Input Voltage Range Because of Special Switching Topology Minimum 200-mA Output Current From an Input Voltage Range to 3.6-V Regulated 3-V 4% Output Voltage No Inductors Required, Low EMI Only Four External Components Required.

MAX5095AAUA+ : High-performance, Single-ended, Current-mode PWM Controllers. The MAX5094A/B/C/D/MAX5095A/B/C BiCMOS, highperformance, current-mode PWM controllers have all the required for wide input-voltage range isolated/nonisolated power supplies. These controllers are used for low- and high-power universal input voltage and telecom power supplies. The MAX5094/MAX5095 contain a fast comparator with only 60ns typical delay.

A102J15C0GF5UAA : Leaded Ceramic Multilayer Capacitors. Mono-axialTM series Leaded ceramic multilayer capacitors Product Supersedes data of 24th October 2001 File under BCcomponents, BC06 2002 Sep 10 Metal end terminations are applied and fired to provide electrical connection between the individual layers. Tinned leads are attached using a solder. Encapsulation consists of a moisture resistant gold colour.

21039-0243 : Ffc, Fpc (flat Flexible), Ribbon - Jumper Cable Assembly 12" (304.80mm); CABLE FLAT FLEX 8POS 1MM 12". s: Pitch: 0.039" (1.00mm) ; Length: 12" (304.80mm) ; Cable Type: FFC ; Number of Conductors: 8 ; Length - Exposed Ends: 0.157" (4.00mm) ; Termination Style: Top on Both Sides, Backers Both Sides ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.

SV13CC223KAR : 0.022F Ceramic Capacitor Radial 630V; CAP CER 22000PF 630V 10% RAD. s: Capacitance: 0.022F ; Voltage - Rated: 630V ; Tolerance: 10% ; Package / Case: Radial ; Temperature Coefficient: X7R ; Packaging: Bulk ; : High Voltage ; Lead Spacing: 0.200" (5.08mm) ; Operating Temperature: -55C ~ 125C ; Mounting Type: Through Hole ; Lead Free Status: Lead.

TAJC157K010RNJ : 150F Tantalum Capacitor 2312 (6032 Metric) 10V; CAP TANT 150UF 10V 10% 2312. s: Capacitance: 150F ; Voltage - Rated: 10V ; Tolerance: 10% ; : General Purpose ; Operating Temperature: -55C ~ 125C ; Lead Spacing: - ; ESR (Equivalent Series Resistance): 900.0 mOhm ; Lifetime @ Temp.: - ; Mounting Type: Surface Mount ; Type: Molded ; Package / Case:.

2866475 : DIN Rail Power Supplies TRIO-PS/1AC/12DC/5A 12VDC 5A. s: Manufacturer: Phoenix Contact ; Product Category: DIN Rail Power Supplies ; RoHS:  Details ; Product: Switching Supplies ; Commercial/Medical: Commercial ; Output Power Rating: 60 W ; Input Voltage: 100 VAC to 240 VAC ; Number of Outputs: 1 ; Output Voltage (Channel 1): 12 V ; Output Current.

LTC1414CGN#TR : Data Acquisition - Analog To Digital Converter (adc) Integrated Circuit (ics) 2 Single-Ended, Bipolar; 1 Differential, Bipolar Tape & Reel (TR) Dual ; IC ADC 14BIT 2.2MSPS SMPL 28SSOP. s: Number of Bits: 14 ; Package / Case: 28-SSOP (0.154", 3.90mm Width) ; Data Interface: Parallel ; Packaging: Tape & Reel (TR) ; Sampling Rate (Per Second):.

405C35B20M00000 : 20MHz Crystal Crystal And Oscillator Surface Mount; CRYSTAL 20.000000 MHZ 13PF SMD. s: Frequency: 20MHz ; Load Capacitance: 13pF ; Package / Case: 4-SMD, No Lead (DFN, LCC) ; Packaging: Cut Tape (CT) ; Frequency Tolerance: 30ppm ; Mounting Type: Surface Mount ; Operating Mode: Fundamental ; Operating Temperature: -20C ~ 70C ; Type: MHz Crystal ; Lead.

ECS-98.3-20-28A-TR : 9.8304MHz Crystal Crystal And Oscillator Surface Mount; CRYSTAL 9.8304MHZ 20PF SMD. s: Frequency: 9.8304MHz ; Load Capacitance: 20pF ; Package / Case: HC49/US ; Packaging: Digi-Reel ; Frequency Tolerance: 30ppm ; Mounting Type: Surface Mount ; Operating Mode: Fundamental ; Operating Temperature: -10C ~ 70C ; Type: MHz Crystal ; Lead Free Status:.

UCC2897AEVM : Eval And Demo Board And Kit Programmers, Development System; EVAL MODULE FOR UCC2897A. s: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.

1623913-9 : Ohm Trimmer Potentiometers, Variable Resistors Top Adjustment Single Turn; TRIMMER 500 OHM 0.2W SMD. s: Resistance (Ohms): 500 ; Power (Watts): 0.2W, 1/5W ; Number of Turns: Single ; Adjustment Type: Top Adjustment ; Tolerance: 25% ; Mounting Type: Surface Mount ; Temperature Coefficient: 250ppm/C ; Resistive Material: Cermet ; Packaging: Tape &.

ST7097 : DATACOM TRANSFORMER FOR GENERAL PURPOSE APPLICATION(S). s: Category: Signal ; Other Transformer Types / Applications: Pulse Transformers, DATACOM TRANSFORMER ; Mounting: Chip Transformer.

15336763 : 19 mm2, TIN FINISH, RING TERMINAL. s: Terminal Type: Ring Terminal ; International: 19 mm2.

1653451001 : 8 CONTACT(S), FEMALE, TWO PART BOARD CONNECTOR, SCREW, SOCKET. s: Connector Type: TWO PART BOARD CONNECTOR ; Gender: Female ; Termination Types: Screw ; Number of Contacts: 8 ; RoHS Compliant: RoHS.

0-C     D-L     M-R     S-Z