|
Details, datasheet, quote on part number:HS-5104ARH-T
| |
| Part: | HS-5104ARH-T |
| Category: | Analog & Mixed-Signal Processing => Amplifiers => Operational Amplifiers => Low Noise |
| Description: | Radiation Hardened Low Noise Quad Operational Amplifier |
| Company: | Intersil Corporation |
| Datasheet: | Download HS-5104ARH-T datasheet File size : 48 kB |
| Request For quote: | Find where to buy HS-5104ARH-T
|
| |
Datasheet text preview:
TM
HS-5104A RH-T
D a t a Sheet J ul y 1999 F N46 06.1
Radiation Hardened Low Noise Quad Operational Amplifier
Intersil`s Satellite Applications Flow TM (SAF) devices are fully tested and guaranteed to 100kRAD total dose. These QML Class T devices are processed to a standard flow intended to meet the cost and shorter lead-time needs of large volume satellite manufacturers, while maintaining a high level of reliability. The HS-5104ARH-T is a radiation hardened, monolithic quad operational amplifier that provides highly reliable performance in harsh radiation environments. Its excellent noise characteristics coupled with a unique array of dynamic specifications make this amplifier well-suited for a variety of satellite system applications. Dielectrically isolated, bipolar processing makes this device immune to Single Event Latch-up. The HS-5104ARH-T shows almost no change in offset voltage after exposure to 100K RAD(Si) gamma radiation, with only a minor increase in current. Complementing these specifications is a post radiation open loop gain in excess of 40K. This quad operational amplifier is available in an industry standard pinout, allowing for immediate interchangeability with most other quad operational amplifiers.
website. www.intersil.com/ · QM L Class T, Per MIL-PRF-38535 · Radiation Performance - Gamma Dose () 1 x 105 RAD(Si) - No Latch-Up, Dielectrically Isolated Device Islands · Low Noise - At 1kHz . . . . . . . . . . . . . . . . . . . . . . . . 4.3nV/Hz (Typ) - At 1kHz . . . . . . . . . . . . . . . . . . . . . . . . 0.6pA/Hz (Typ) · Low Offset Voltage. . . . . . . . . . . . . . . . . . . . .3.0mV (Max) · High Slew Rate . . . . . . . . . . . . . . . . . . . . . . 2.0V/µs (Typ) · Gain Bandwidth Product . . . . . . . . . . . . . . . 8.0MHz (Typ)
Pinouts
HS1-5104ARH-T (SBDIP), CDIP2-T14 TOP VIEW
1 2 3 4 5 6 7 14 OUT 4 13 -IN4 12 +IN4 11 V10 +IN3 9 8 -IN3 O UT 3
OUT 1 -IN1 +IN1 V+ +IN2 -IN2 OUT 2
Specifications
Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed below must be used when ordering. Detailed Electrical Specifications for the HS-5104ARH-T are contained in SMD 5962-95690. For more information, visit our website at: www.intersil.com/ Intersil`s Quality Management Plan (QM Plan), listing all Class T screening operations, is also available on our
O UT 1 -IN1 +IN1 V+ +IN2 -IN2 O UT 2
HS9-5104AR H-T (FLATPACK), CDFP3-F14 TOP VIEW
1 2 3 4 5 6 7 14 13 12 11 10 9 8 OUT 4 -IN4 +IN4 V+IN3 -IN3 OUT 3
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved Satellite Applications FlowTM (SAF) is a trademark of Intersil Corporation.
HS-5104ARH-T Die Characteristics
DIE DIMENSIONS: (2420µm x 2530µm x 483µm ±25.4µm) 95 x 99 x 19mils ±1mil METALLIZATION: Type: Al Si Cu Thickness: 16.0kÅ ±2kÅ SUBSTRATE POTENTIAL: Unbiased (DI) BACKSIDE FINISH: Silicon PASSIVATIO N: Type: Nitride (Si3N4) over Silox (SiO2) Nitride Thickness: 3.5kÅ ±1.5kÅ Silox Thickness: 12.0kÅ ±2kÅ WORST CASE CURRENT DENSITY: < 2.0e5 A/cm 2 TRANSISTOR COUNT: 175 PROCESS: Bipolar DI
Metallization Mask Layout
HS-5104ARH-T
+IN2 V+ +I N1
-IN2
-IN1
OUT2 OUT3
O UT 1 O UT 4
-IN3
-IN4
+I N3
V-
+I N4
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 2
|
|
