Details, datasheet, quote on part number: RH108A
CategoryAnalog & Mixed-Signal Processing => Amplifiers => Operational Amplifiers => General Purpose => Single
DescriptionOperational Amplifier
CompanyLinear Technology Corporation
DatasheetDownload RH108A datasheet
Find where to buy


Features, Applications


The is a precision operational amplifier particularly well-suited for high source impedance applications requiring low offset and bias currents and low power consumption. The wafer lots are processed to Linear Technology's inhouse Class S flow to yield circuits usable in stringent military applications. For complete electrical specifications, performance curves and applications information, see the LM108A/LM108 data sheet.

Supply Voltage...................................................... ± 20V Differential Input Current (Note ± 10mA Input Voltage (Note ± 15V Output Short-Circuit Duration......................... Indefinite Operating Temperature Range.............. to 125°C Storage Temperature Range................. to 150°C Lead Temperature (Soldering, 10 sec).................. 300°C

SYMBOL PARAMETER VOS V OS Temp IOS IS Temp IB AVOL CMRR PSRR Input Offset Voltage Average Tempco of Offset Voltage Input Offset Current Average Tempco of Offset Current Input Bias Current Large-Signal Voltage Gain ± 15V, VOUT RL 10k Common Mode Rejection Ratio Power Supply Rejection Ratio Input Voltage Range VOUT RIN IS Output Voltage Swing Input Resistance Supply Current (Note 0.2 1 CONDITIONS NOTES

SYMBOL PARAMETER VOS IOS IB AVOL CMRR PSRR Input Offset Voltage Input Offset Current Input Bias Current Large-Signal Voltage Gain Common Mode Rejection Ratio Power Supply Rejection Ratio Input Voltage Range VOUT RIN IS Output Voltage Swing Input Resistance Supply Current ± 15V, VOUT RL 10k CONDITIONS

Note 1: Differential input voltages greater than 1V will cause excessive current to flow through the input diodes unless limiting resistance is used. Note 2: For supply voltages less than ±15V, the maximum input voltage is equal to the supply voltage.

Note 3: Guaranteed by design, characterization or correlation to other tested parameters. Note ± 20V unless otherwise noted. Note ± 15V, VCM = 25°C unless otherwise noted. Note A 125°C.

MIL-STD-883 TEST REQUIREMENTS Final Electrical Test Requirements (Method 5004) Group A Test Requirements (Method 5005) Group C and D End Point Electrical Parameters (Method 5005) * PDA Applies to subgroup 1. See PDA Test Notes. SUBGROUP 1,2,3,4,5,6 1 PDA Test Notes The PDA is specified as 5% based on failures from group A, subgroup 1, tests after cooldown as the final electrical test in accordance with method of MIL-STD-883 Class B. The verified failures (including Delta parameters) of group A, subgroup 1, after burn-in divided by the total number of devices submitted for burn-in in that lot shall be used to determine the percent for the lot. Linear Technology Corporation reserves the right to test to tighter limits than those given.

Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.


Some Part number from the same manufacture Linear Technology Corporation
RH111 Voltage Comparator
RH117 Positive Adjustable Regulator
RH118 Precision, High Speed Operational Amplifier
RH119 High Performance Dual Comparator
RH129 6.9V Precision Reference
RH137 Negative Adjustable Regulator
RH27C Precision Operational Amplifier
SG1524 Regulating Pulse Width Modulator
SL30495 Zero Drift Rail-to-rail In/out Precision in Amp For Use With LTC1923 in Tec Apps
T1070HV 5a And 2.5a High Efficiency Switching Regulators
T1074HV Step-down Switching Regulator
LTC4063 Standalone Linear Li-Ion Charger with Micropower Low Dropout Linear RegulatorThe LTC®4063 is a standalone linear charger for single cell lithium-ion batteries with an adjustable low dropout linear regulator
LT3483 Inverting Micropower DC/DC Converter with Schottky in ThinSOT PackageThe LT®3483 is a micropower inverting DC/DC converter with integrated Schottky and one resistor feedback. The small package size,
LT5525 High Linearity, Low Power Downconverting MixerThe LT®5525 is a low power broadband mixer optimized for high linearity applications such as point-to-point data transmission, high performance radios and wireless

LTC1649IS : Step-Down LTC1649, 3.3V Input High Power Step-down Switching Regulator Contoller

LTC2908 : Precision Six Supply Monitor.six Supply Monitor For Systems With a Large Number of Supply Voltages That Require a Precise And Compact Solution. The Common Reset Output Remains Low Until All Six Inputs Have Been in Compliance For 200ms.FEATURESUltralow Voltage Reset: VCC = 0.5

LTC4441IS8-1 : High Speed Synchronous N-channel Mosfet Driver

LTC2281CUP-PBF : Dual 10-bit, 125msps Low Power 3V ADC

LTC3523EUD-TRPBF : 400ma Micropower Synchronous Step-up Dc/dc Converter with Output Disconnect

LTC2158CUP-14#TRPBF : Dual 12-Bit 310Msps ADC The LTCĀ®2158-12 is a 2-channel simultaneous sampling 310Msps 12-bit A/D converter designed for digitizing high frequency, wide dynamic range signals. It is perfect for demanding communications applications with AC performance that includes 67.6dB SNR and 88dB spurious free

LT1171CQ#TRPBF : Pmic - Voltage Regulator - Dc Dc Switching Regulator Integrated Circuit (ics) Step-Down (Buck), Step-Up (Boost), Inverting, Cuk, Flyback, Forward Converter No 1.25 V ~ 40 V; IC MULTI CONFIG ADJ 2.5A D2PAK Specifications: Type: Step-Down (Buck), Step-Up (Boost), Inverting, Cuk, Flyback, Forward Converter ; Output Type: Adjustable ; PWM Type: Current Mode ; Synchronous Rectifier: No ; Number of Outputs: 1 ; Voltage - Output: 1.25 V ~ 40 V ; Current - Output: 2.5A ; Frequency - Switching: 100kHz ; Volta

LTC6248IMS#PBF : Linear - Amplifier - Instrumentation, Op Amps, Buffer Amp Integrated Circuit (ics) General Purpose Tube 1.25mA 2.5 V ~ 5.25 V, ±1.25 V ~ 2.625 V; IC OPAMP R-R 120MHZ QUAD 16MSOP Specifications: Packaging: Tube ; Amplifier Type: General Purpose ; Number of Circuits: 4 ; Package / Case: 16-TFSOP (0.118", 3.00mm Width) ; Slew Rate: 90 V/µs ; Gain Bandwidth Product: 180MHz ; Current - Supply: 1.25mA ; Current - Output / Channel: 100mA ; Voltage - Supply, Single/Dual (±): 2.5 V

LT1019AIS8-2.5#TR : 10V LT1019ACN8-10, Precision References

LT3791HFE-1#TRPBF : 60V 4-Switch Synchronous Buck-Boost Controller The LT®3791-1 is a synchronous 4-switch buck-boost voltage/ current regulator controller. The controller can regulate output voltage, output current, or input current with input voltages above, below, or equal to the output voltage. The constant-freque

LTC2156CUP-14TRPBF : 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 Specifications: Package Type: 9 X 9 MM, LEAD FREE, PLASTIC, MO-220WNJR-5, QFN-64 ; Screening Level: Commercial ; Pins: 64 ; Operating Temperature: 0.0 to 70 C (32 to 158 F) ; Sample Rate: 210000 kSamples/Sec ; Input Voltage: -1.5 to 1.5 volts

Same catergory

LT1342 : 5V RS232 Transceiver With 3V Logic Interface. ESD Protection Over ±10kV 3V Logic Interface Uses Small Capacitors: 0.2µF 1µA Supply Current in Shutdown Low Power Driver Disable Operating Mode Pin Compatible with LT1137A 120kBaud Operation for 2500pF 250kBaud Operation for = 1000pF CMOS Comparable Low Power: 60mW Operates from a 5V Supply and 3V Logic Supply Easy PC Layout: Flowthrough Architecture.

MAP40-1005 : Wide Range Input For 110/220 Vac Applications. Power-One's MAP55 series of power supplies provides reliable, tightly regulated DC power for commercial and industrial systems. Widerange AC input and full international safety, EMI, and ESD compliance ensure world-wide acceptance. All units bear the CE Mark. The MAP55 utilizes a thermally efficient U-channel chassis design, which allows full power.

MAX320 : Precision, Dual Supply, Spst, Analog CMOS Switches. The MAX320/MAX321/MAX322 are precision, dual, SPST analog switches designed to operate from to ±8V dual supplies. The MAX320 has two normally open (NO) switches and the MAX321 has two normally closed (NC) switches. The MAX322 has one NO and one NC switch. Low power consumption (1.25mW) makes these parts ideal for battery-powered equipment. They offer.

MAX3262 : 1Gbps, High-speed Limiting Amplifier With Chatter-free Loss of Signal Detection.

MAX400CPA : Ultra Low Offset Voltage Operational Amplifier.

MC33362 : Power. High Voltage Switching Regulator. The is a monolithic high voltage switching regulator that is specifically designed to operate from a rectified 120 VAC line source. This integrated circuit an on­chip V/2.0 A SENSEFETt power switch, 250 V active off­line startup FET, duty cycle controlled oscillator, current limiting comparator with a programmable threshold and leading edge blanking,.

MCCF79076 : Electronic Ignition Control Circuit. Order this document from Analog Marketing The MCCF79076, in conjunction with an appropriate Motorola Power Darlington Transistor, provides an economical solution for automotive ignition applications. The MCCF79076 offers optimum performance by providing closed loop operation of the Power Darlington in controlling the ignition coil current. The MCCF79076.

NE555 : NE/SA/SE555/SE555C; Timer. The 555 monolithic timing circuit is a highly stable controller capable of producing accurate time delays, or oscillation. In the time delay mode of operation, the time is precisely controlled by one external resistor and capacitor. For a stable operation as an oscillator, the free running frequency and the duty cycle are both accurately controlled.

NJG1705V-C1 : 1.5/1.9ghz Band Front-end GAAS Mmic. n GENERAL is a front-end GaAs MMIC including a LNA, local amplifier and a Mixer, designed mainly for 1.5 and 1.9GHz band cellular phone. NJG1705V exhibits low noise at 1.5GHz and 1.9GHz at low total current consumption 9.5mA. n l Low voltage operation l Low current consumption l High conversion gain l Low noise figure l High IIP3 l Package n PIN CONFIGURATION.

SAA2502 : SAA2502; ISO/mpeg Audio Source Decoder. Preliminary Supersedes data of 1997 Apr 18 File under Integrated Circuits, IC01 1997 Nov 17 CONTENTS APPLICATIONS GENERAL ORDERING INFORMATION BLOCK DIAGRAM PINNING FUNCTIONAL Basic functionality Clock generator module External sample clock Free running internal sample clock Locked internal sample clock Limited sampling frequency support for internal.

SN55LBC174FK : Quadruple Low-power Differential Line Driver. Meets EIA Standard RS-485 Designed for High-Speed Multipoint Transmission on Long Bus Lines in Noisy Environments Supports Data Rates up to and Exceeding Ten Million Transfers Per Second Common-Mode Output Voltage Range 12 V Positive- and Negative-Current Limiting Low Power Consumption. 1.5 mA Max (Output Disabled) The SN55LBC174 is composed of monolithic.

TLV2450CD : ti TLV2450, Single Micropower Rail-to-rail Input/output op Amp W/shutdown.

UCC3981 : Power. Universal Serial Bus Hot Swap Power Controller. Fully USB Compliant Support Four 5V Peripherals and One USB 3.3V Controller Separate Power Enables 500mA Current Limiting per Channel Separate Open Drain Fault Indicator for Each Channel 3.3V Output for USB Controller Available in 28 Pin Wide Surface Mount and DIP The UCC3981 Hot Swap Power Controller is designed to provide a self powered USB hub with.

LMH6553 : 900 MHz Fully Differential Amplifier With Output Limiting Clamp From The PowerWise® Family The LMH6553 is a 900 MHz differential amplifier with an integrated adjustable output limiting clamp. The clamp increases system performance and provides transient over-voltage protection to following stages. The internal clamp feature of the LMH6553 reduces or eliminates.

0-C     D-L     M-R     S-Z