Details, datasheet, quote on part number: SW-395PIN
PartSW-395PIN
CategoryRF & Microwaves => Switches
DescriptionDC-2 Ghz, 3 V GAAS SPDT Switch
CompanyM/A-COM, Inc.
DatasheetDownload SW-395PIN datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Features

Low Insertion Loss: @ 900 MHz Low Power Consumption: @ =3 VDC Very High Intercept Point: 52 dBm IP3 Both Positive and Negative 8 V Control Low Cost SOT-26 Package

Description

M/A-COM's is a GaAs monolithic switch in a low cost SOT-26 surface mount plastic package. The SW-395 is ideally suited for applications where very low power consumption, low intermodulation products, very small size and low cost are required. Typical application is an internal/external antenna select switch for portable telephones and data radios. In addition, because of its low loss, good isolation and inherent speed, the SW-395 can be used as a conventional T/R switch as an antenna diversity switch. The SW-395 can be used in power applications to 0.5 Watts in systems such as cellular, PCN, GSM an other analog/digital wireless communications systems. The SW-395 is fabricated using a mature 1-micron gate length GaAs MESFET process. The process features full chip passivation for increased performance and reliability.

Part Number SW-395 PIN SW-395TR Package SOT-26 Plastic Package Forward Tape and Reel
1. Refer to Application Note M513 for reel size information.
Parameter Insertion Loss Isolation VSWR 1 dB Compression
Trise, Tfall Ton, Toff Transients Input IP2 Input IP3

Test Conditions - 1.0 GHz - 2.0 GHz - 1.0 GHz - 2.0 GHz - 2.0 GHz Input Power (3V Control) 0.5 GHz Input Power (5V Control) 0.5 GHz Input Power (3V Control) 0.05 GHz Input Power (5V Control) 0.05 GHz to 90% RF, RF 50% Control to 90% RF, Control 10% RF In-band 2-Tone, 5 MHz spacing, 3 V Control 0.05 GHz +10 dBm each 0.5 GHz 2-Tone, 5 MHz spacing, 3 V Control 0.05 GHz +10 dBm each 0.5 GHz

All measurements at 1 GHz a 50 system with a 3V control unless otherwise specified. Loss varies at 0.003 dB/C.

AMP and Connecting at a Higher Level are trademarks. Specifications subject to change without notice.

Parameter Input Power Operating Voltage Operating Temperature Storage Temperature
Exceeding any one or a combination of these limits may cause permanent damage.
On Off On Off 1. DC blocking capacitors not required if negative control voltage is used.

1. External DC blocking capacitors are required on all RF ports. 2. |-Vc|< 3. If negative control is used, DC blocking capacitors are not required on RF ports.

Insertion Loss vs. Frequency INSERTION LOSS vs FREQUENCY

 

Related products with the same datasheet
SW-395TR
Some Part number from the same manufacture M/A-COM, Inc.
SW-395TR DC-2 Ghz, 3 V GAAS SPDT Switch
SW-399
SW-415 DC-2 Ghz, Matched GAAS SP4T Switch
SW-419 DC-2 Ghz, GAAS SP4T Terminated Switch
SW-419PIN GAAS Sp4t Terminated Switch DC - 2 GHZ
SW-419RTR DC-2 Ghz, GAAS SP4T Terminated Switch
SW-425 DC-3 Ghz, 3 Watt Cellular T/r And Antenna Changeover Switch
SW-437 DC-3 Ghz, GAAS SPDT Switch
SW-437PIN GAAS SPDT Switch DC - 3.0 GHZ
SW-437RTR DC-3 Ghz, GAAS SPDT Switch
SW-438  GaAs SPDT Switch DC - 3.0 GHZ
SW-439 DC-3 Ghz, GAAS High ISOlation Switch
SW-439PIN GAAS High ISOlation Switch DC - 3.0 GHZ
SW-439PIN DC-3 Ghz, GAAS High ISOlation Switch
SW-442 DC-3 Ghz, GAAS SPDT Terminated Switch
SW-442PIN GAAS SPDT Terminated Switch DC - 3.0 GHZ
SW-442PIN DC-3 Ghz, GAAS SPDT Terminated Switch
SW-444 2v Control Triple-band Gsm/dcs/pcs Sp5t Switch 0.5 . 2.0 GHZ
SW-444SMB
SW-444TR
SW-456 DC-3 Ghz, GAAS SPDT Switch
 
0-C     D-L     M-R     S-Z