|Category||RF & Microwaves => Switches|
|Description||DC-3 Ghz, GAAS SPDT Terminated Switch|
|Datasheet||Download SW-442 datasheet
Low Cost Plastic SOT-26 Package Low Insertion Loss @ 900 MHz High Isolation @ 900 MHz Low Power Consumption @ +3V Positive or Negative 8 V ControlDescription
M/A-COM's is a GaAs monolithic switch in a low cost SOT-26 surface mount plastic package. The SW-442 is ideally suited for applications where very low power consumption, low insertion loss, very small size and low cost are required. Typical application is in dual band systems where switching between small signal components is required such as filter banks, single band LNA's, converters etc. The SW-442 can be used in applications to 0.25 Watts in systems such as CDMA, W-CDMA, PCS, DCS1800, GSM and other analog/digital wireless communications systems. The SW-442 is fabricated using a mature 0.8 micron GaAs MESFET process. The process features full passivation for increased performance and reliability.
Part Number SW-442 PIN SW-442RTR SW-442SMB Package SOT-26 Plastic Package 1 Forward Tape and Reel 1 Reverse Tape and Reel Sample Board1. Reference Application Note M513 for reel size information.
VSWR P1dB (2.7V supply) P1dB (5V supply) IP2 (2.7V supply) IP3 (2.7V supply) Trise, Tfall Ton, Toff Transients Gate Leakage
2-Tone 900 MHz, 5 MHz spacing, 10 dBm each tone 2-Tone 900 MHz, 5 MHz spacing, 10 dBm each tone to 90% RF, RF 50% Control to 90% RF, Control 10% RF In-Band VCTL = 2.5V
AMP and Connecting at a Higher Level are trademarks. Specifications subject to change without notice.
Parameter Input Power - 3.0 GHz) 3V Control 5V Control Operating Voltage Operating Temperature Storage Temperature1. Exceeding any one or combination of these limits may cause permanent damage.
1. External DC blocking capacitors are required on all RF ports and GND. GND capacitors can be used with postive control voltage to resonate lead inductance for improved isolation. 2. If negative control is used, DC blocking capacitors and GND capacitors are not required.
PIN No. Function RF1 GND RF2 V2 RFC V1 Description RF in/out RF Ground RF in/out V Control 2 RF COMMON V Control 1The following precautions should be observed to avoid damage:
Static Sensitivity Gallium Arsenide Integrated Circuits are ESD sensitive and can be damaged by static electricity. Proper ESD techniques should be used when handling these devices.Output VSWR vs. Frequency over Temperature Input VSWR vs. Frequency over Temperature
Isolation Loss vs. Frequency over Temperature (Postive Control)
Isolation Loss vs. Frequency over Temperature (Negative Control)
Insertion Loss vs. Frequency over Temperature (Postive Control)
Insertion Loss vs. Frequency over Temperature (Negative Control)
|Related products with the same datasheet|
|Some Part number from the same manufacture M/A-COM, Inc.|
|SW-442PIN GAAS SPDT Terminated Switch DC - 3.0 GHZ|
|SW-442PIN DC-3 Ghz, GAAS SPDT Terminated Switch|
|SW-444 2v Control Triple-band Gsm/dcs/pcs Sp5t Switch 0.5 . 2.0 GHZ|
|SW-456 DC-3 Ghz, GAAS SPDT Switch|
|SW-456TR3000 2v Control Triple-band Gsm/dcs/pcs Sp5t Switch 0.5 . 2.0 GHZ|
|SW-456TR3000 DC-3 Ghz, GAAS SPDT Switch|
|SW-461 800-900 Mhz, 4 X 6 RF Switch Matrix|
|SW-475 0.5-3 Ghz, SPDT High ISOlation Terminated Switch|
|SW-485 0.05-3 Ghz, GAAS SPDT Switch|
|SW-488 2 V Dual-mode Wcdma & Dual-band Gsm/dcs Switch 0.5 . 2.0 GHZ|
|SW-489 GaAs SP3T 2.5V High Power Switch DC - 2.5 GHZ|
|SW05-0311 DC-3 Ghz, Match GAAS SPST Absorptive Switch|
|SW10-0312 DC-3 Ghz, GAAS SPDT Reflective Switch|
|SW10-0313 DC-3 Ghz, Matched GAAS SPDT Reflective Switch|
|SW15-0314 DC-3 Ghz, GAAS SP4T Absorptive Switch|
|SW65-0003 DC-2500 Mhz, GAAS SP8T Reflective Switch|
|SW65-0014 DC-3 Ghz, GAAS SPST Absorptive Switch With Asic Driver|
|SW65-0114 DC-3 Ghz, GAAS SPDT Absorptive Switch With Asic Driver|
AM50-0004RTR : LNAs 1400-2000 Mhz, High Dynamic Range Low Noise Amplifier
AT-263PIN : Digital Attenuator, 31 DB, 5-Bit, TTL Driver, DC - 2 GHZ
ESDC-13-2-75 : 5 MHz - 1000 MHz RF/MICROWAVE DIRECTIONAL COUPLER, 2.2 dB INSERTION LOSS-MAX Specifications: RF Coupler Type: Uni-Directional ; Package Type: Surface Mount, SM-1, 6 PIN ; Impedance: 75 ohms ; Frequency Range: 5.00 to 1000.00 MHz ; Insertion Loss: 2.20 dB
FW100H9 : 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE Specifications: Output Voltage: 21.6 to 26.4 volts ; Input Voltage: 36 to 72 volts ; Output Power: 100 watts (0.1340 HP) ; Operating Temperature: 0.0 to 90 C (32 to 194 F)
MA48706B155 : mm WAVE BAND, GALLIUM ARSENIDE, STEP RECOVERY DIODE Specifications: Configuration: Single ; Pin Count: 2 ; Number of Diodes: 1 ; VBR: 25 volts ; CT: 0.1500 to 0.2490 pF
MA4T64533 : X BAND, Si, NPN, RF SMALL SIGNAL TRANSISTOR Specifications: Polarity: NPN ; Number of units in IC: 1 ; Operating Frequency: 8000 MHz
MABA-007748-CT11TB : 5 MHz - 1200 MHz RF TRANSFORMER Specifications: Category: Signal ; Other Transformer Types / Applications: RF ; Mounting: Chip Transformer ; Operating Temperature: -20 to 85 C (-4 to 185 F) ; Standards: RoHS
MAFR-000663-000001 : 2500 MHz - 2700 MHz RF/MICROWAVE 3 PORT CIRCULATOR Specifications: Component: Circulator ; Package Size: ROHS COMPLIANT PACKAGE-3 ; Frequency Range : 2500 to 2700 MHz ; Insertion Loss: 0.2500 dB ; Operating Temperature: -40 to 85 C (-40 to 185 F)
ML4611P-101 : 40 V, SILICON, PIN DIODE Specifications: Number of Diodes: 1
ML6528-102D : 500 MHz - 18000 MHz RF/MICROWAVE SGL POLE SGL THROW SWITCH, 2.7 dB INSERTION LOSS Specifications: Frequency Range: 500 to 18000 MHz ; Insertion Loss: 2.7 dB ; VSWR: 1.9 1 ; Type: Single Pole Single Throw ; Operating Temperature: -55 to 85 C (-67 to 185 F)
MLA2657-403C2 : 10700 MHz - 11700 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER Specifications: Amplifier Type: Power Amplifier ; Applications: RF Microwave ; Frequency Range: 10700 to 11700 MHz ; Input VSWR: 1.8 1 ; Output VSWR: 1.8 1 ; Operating Temperature: -55 to 95 C (-67 to 203 F)
2661-1005-30 : 500 MHz - 2000 MHz RF/MICROWAVE SGL POLE SGL THROW SWITCH, 1.2 dB INSERTION LOSS Specifications: Frequency Range: 500 to 2000 MHz ; Insertion Loss: 1.2 dB ; VSWR: 1.5 1 ; Impedance: 50 ohms ; Type: Single Pole Single Throw ; Operating Temperature: -55 to 95 C (-67 to 203 F)
1X505 : = Xinger Directional Couplers ;; Size LXWXH = 0.56 X 0.2 X 0.081" ;; Packaging = Surface Mount ;; Frequency MHZ = 1700-2000 ;; Power Handling Watts = 60.
4ASSA0306 : = Connectorized ;; Size LXWXH = 6.0 X 1.12 X 0.2" ;; Packaging = Multilayer Circuit ;; Frequency MHZ = 1800-2200 ;; Power Handling Watts = 15.
AD3PS-1 : Power Splitter. Power Splitter. Aqueous washable. For non-aqueous washable requirements, LRPS models available in case style QQQ130. o Non-hermetic n Denotes 75 Ohm model, for coax connector models 75 Ohm BNC connectors are standard. < At low range frequency band (fL to 10 fL), linearly derate maximum input power by 13 dB. J When for only M range given, s apply to entire frequency.
BX6416 : Frequency (MHz) = 5 - 500 ;; Gain (Typ/Min) (dB) = 15 / 14 ;; Noise Figure (Typ/Max) (dB) = 3.5 / 4.5 ;; P1dB Comp Point (Typ/Min) (dBm) = +13.5 / +12 ;; 3rd Order Intercept (Typ) (dBm) = +27 ;; 2nd Order Intercept (Typ) (dBm) = +35 ;; DC Power (Typ) (V/mA) = +15 / +35 ;; Package = Package = Package = 4 Pin TO-8 Package = Surface Mount Package = Flatpack.
CH20-0032-17G : E-Glass SMT 17 DB Bi-directional Coupler 824 - 960 MHZ. Device is Bi-Directional Small Size and Low Profile Industry Standard SOIC-8 SMT Plastic Package Superior Repeatability Typical Insertion Loss 0.3 dB Typical Directivity dB 2 Watt Power Handling M/A-COM's an IC based monolithic bidirectional coupler in a low cost SOIC-8 plastic package. This 17 dB coupler is ideally suited for applications where power.
EMRS-6X1 : E-Series SMT Schottky Mixer 1805 - 1880 & 925 - 960 MHZ. M/A-COM's is a low drive , surface mount mixer suitable for use in wireless applications. M/A-COM Division of AMP Incorporated s North America: Tel. (800) 366-2266, Fax 618-8883 s Asia/Pacific: 2111 8088, Fax s Europe: Tel. 300 020 AMP and Connecting at a Higher Level are trademarks. s subject to change without notice. Parameter RF Power Peak IF Current.
F1014 : Power. Pout W = 20 ;; Freq MHZ = 400 ;; Gain DB = 12 ;; Theta JC = 2.1 ;; GM Mho = 1.6 ;; Idsat a = 11 ;; Ciss PF = 66 ;; CRSS PF = 8 ;; Coss PF = 40 ;; Die = 2 ;; Style = Single Ended ;; PKG = ap.
FLK027WG : FET. C,x,ku-band Power GAAS Fets. High Output Power: = 24.0dBm(Typ.) High Gain: = 7.0dB(Typ.) High PAE: add = 32%(Typ.) Proven Reliability Hermetic Metal/Ceramic Package The is a power GaAs FET that is designed for general purpose applications in the Ku-Band frequency range as it provides superior power, gain, and efficiency. Fujitsu's stringent Quality Assurance Program assures the highest.
HMC136 : Bi- Phase Modulator 4- 8 GHZ. Chip Integrates Directly into MIC Designs dB of Carrier Suppression Direct Modulation in the - 8 GHz Band Functions also as a Phase Detector Typical Applications The HMC136 is suitable for: Wireless Local Loop LMDS & VSAT Pt. to Pt. Radios Test Equipment The HMC136 Bi-Phase Modulator is designed to phase-modulate an RF signal into reference and 180 degree.
L8801P : Power. Pout W = 10 ;; Freq MHZ = 500 ;; Gain DB = 10 ;; Theta JC = 5 ;; GM Mho = 0.8 ;; Idsat a = 5.5 ;; Ciss PF = 30 ;; CRSS PF = 1 ;; Coss PF = 15 ;; Die = 1 ;; Style = Single Ended ;; PKG = S08P ;; = P ;; = a ;; = S.
RD15HVF1 : VHF, UHF and 900MHz. is a MOS FET type transistor specifically designed for VHF/UHF High power amplifiers applica -tions. OUTLINE DRAWING High power and High Gain: Gp>7dB @Vdd=12.5V,f=520MHzHigh Efficiency: 60%typ. on VHF BandHigh Efficiency: 55%typ. on UHF Band APPLICATION For output stage of high power amplifiers in VHF/UHF Band mobile radio sets. SYMBOL VDSS VGSS.
RFP-25-1AP : = Attenuators ;; Size LXWXH = 0.25 X 0.515 X 0.13" ;; Packaging = Flanged ;; Frequency MHZ = 0-3000 ;; Power Handling Watts = 25.
SQ201 : Power. Pout W = 8 ;; Freq MHZ = 1000 ;; Gain DB = 10 ;; Theta JC = 7 ;; GM Mho = 0.3 ;; Idsat a = 1.4 ;; Ciss PF = 10 ;; CRSS PF = 0.6 ;; Coss PF = 6 ;; Die = 1+1 ;; Style = Push - Pull ;; PKG = aq ;; = P ;; = a ;; = S.
HMC576LC3B : The HMC576LC3B is a x2 active broadband frequency multiplier utilizing GaAs PHEMT technology in a leadless RoHS compliant SMT package. When driven by a +3 dBm signal, the multiplier provides +15 dBm typical output power from 18 to 29 GHz. The Fo and 3Fo isolations are >20 dBc at 24 GHz. The HMC576LC3B is ideal for use in LO multiplier chains for Pt to Pt & VSAT.
HMC-ALH445 : Velocium LNA MMICs Target Microwave & Millimeterwave Radios The HMC-ALH445 is a GaAs MMIC HEMT sel f-biased, wideband Low Noise Amplii er die which operates between 18 and 40 GHz. The amplii er provides 9 dB of gain, 3.9 dB noise i gure at 28 GHz and +12 dBm of output power at 1 dB gain compression while requiring only 45 mA from a single +5V supply.
HMC-MDB277 : GaAs MMIC FUNDAMENTAL MIXER, 70 - 90 GHz The HMC-MDB277 is a passive Double Balanced MMIC Mixer which utilizes GaAs Heterojunction Bipolar Transistor (HBT) Shottky diode technology and can be used as either an upconverter or a downconverter. All bond pads and the die backside are Ti/Au metallized and the Shottky devices are fully passivated for reliable.
RF5510 : 11B/G WLAN SP3T Switch The RF5510 is a SP3T switch designed in a small 0.88mm x 0.80mm x 0.38mm FLIP CHIP die. This device is capable of switching between WLAN RX, WLAN TX, and Bluetooth™ receive modes simutaneously with a slight increase in insertion loss. This device meets or exceeds the RF switch needs of IEEE802.11b/g WLAN RF systems.
SKY13366-378LF : 2.0-6.0 GHz GaAs SPDT Switch The SKY13366-378LF is a pHEMT GaAs FET I/C switch. The switch may be used in transmit/receive applications by connecting the RF common port (INPUT, pin 5) to either the OUTPUT1 or OUTPUT2 port (pin 1 or 3, respectively) using a low loss path (i.e., a positive voltage applied to either VCTL1 or VCTL2 pins). The switch is “reflective.