|Category||RF & Microwaves => Switches|
|Description||DC-3 Ghz, GAAS SPST Absorptive Switch With Asic Driver|
|Datasheet||Download SW65-0014 datasheet
|GaAs SPST Absorptive Switch with ASIC Driver, - 3.0 GHz
Typical Isolation: dB (2,000 MHz) Typical Insertion Loss: dB (2,000 MHz) Integral ASIC TTL/CMOS Driver Plastic, 50 mil Pitch, SOW-24 Lead, Wide Body Low DC Power Consumption 50 Ohm Nominal Impedance Tape and Reel Packaging Available Test Boards AvailableDescription
M/A-COM's is a GaAs MMIC absorptive SPST switch with an integral silicon ASIC driver. This device a 24-lead plastic package. This switch offers excellent broadband performance and repeatability from to 3 GHz, while maintaining low DC power dissipation. The SW65-0014 is ideally suited for wireless infrastructure applications. Also available in ceramic package with improved performance.
Parameter Insertion Loss Isolation (All arms off) VSWR Trise Tfall Ton Toff Transients 1 dB Compression Input IP3 VCC VEE ICC IEE Logic "0" Logic "1" Test Conditions - 3.0 GHz - 3.0 GHz Units dB Min 35 On Typical 1.8 42 Off 2.0:1 Max 2.21. Decoupling capacitors (.01 µF) are required on the power supply lines.
GaAs SPST Absorptive Switch with ASIC Driver, - 3.0 GHz
Parameter Max. Input Power 0.05 GHz - 3.0 GHz Bias Voltages VEE VCC Control Voltage 4 Operating Temperature Storage Temperature Absolute Maximum +27 dBm +34 dBm -0.5V to VCC to +125°C
2. Operation of this device above any one of these parameters may cause permanent damage. 3. When the RF input is applied to the terminated port, the absolute maximum power is +30 dBm. 4. Standard CMOS TTL interface, latch-up will occur if logic signal is applied prior to power supply.
Part Number SW65-0014TR SW65-0014-TB Package Bulk Packaging Tape and Reel (1K Reel) Units Mounted on Test Board
Specifications subject to change without notice. n North America: Tel. 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. 300 020Visit www.macom.com for additional data sheets and product information.
|Related products with the same datasheet|
|Some Part number from the same manufacture M/A-COM, Inc.|
|SW65-0014-TB DC-3 Ghz, GAAS SPST Absorptive Switch With Asic Driver|
|SW65-0114 DC-3 Ghz, GAAS SPDT Absorptive Switch With Asic Driver|
|SW65-0214 DC-3 Ghz, GAAS SP3T Absorptive Switch With Asic Driver|
|SW65-0313 DC-3 Ghz, GAAS SP2T Absorptive Switch With Asic Driver|
|SW65-0314 DC-3 Ghz, GAAS SP4T Absorptive Switch With Asic Driver|
|SW90-0001 DC-4 Ghz, GAAS SPST Switch, Absorptive, Single Supply|
|SW90-0002 DC-4 Ghz, GAAS SPDT Switch, Absorptive, Single Supply|
|SW90-0003 DC-4 Ghz, GAAS SP4T Switch, Absorptive, Single Supply|
|SW90-0004 DC-4 Ghz, GAAS SP6T Switch, Absorptive, Single Supply|
|SW90-0004A GaAs SP6T Switch, Absorptive, Single Supply, DC - 4 GHZ|
|SW90-0004TR DC-4 Ghz, GAAS SP6T Switch, Absorptive, Single Supply|
|SWD-109 Single/quad Driver For GAAS Fet Switche And Attenuator|
|SWD-109PIN Single/quad Drivers For GAAS Fet Switches And Attenuators|
|SWD-109RTR Single/quad Driver For GAAS Fet Switche And Attenuator|
|SWD-119PIN Single/quad Drivers For GAAS Fet Switches And Attenuators|
|SWD-119RTR Single/quad Driver For GAAS Fet Switche And Attenuator|
|T-1000 Two-Way Power Splitter/Combiner, 10 - 1000MHz|
|THV-50 Two-Way Power Splitter/Combiner, 2 - 200MHz|
|TP-101 RF Pulse Transformer, 500 KHZ - 1.5 GHZ|
ML4206-94 : 15 V, SILICON, PIN DIODE Specifications: Number of Diodes: 1
ML6719-120 : 18000 MHz - 40000 MHz RF/MICROWAVE LIMITER Specifications: Limiter Type: Pin Diode Limiter ; Frequency Band: 18000.0 to 40000.0 MHz ; VSWR: 2.50 1
ML6742-154 : 100 MHz - 500 MHz RF/MICROWAVE LIMITER Specifications: Limiter Type: Pin Diode Limiter ; Frequency Band: 100.0 to 500.0 MHz ; VSWR: 1.30 1
MLA2555-201A1 : 8500 MHz - 9500 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER Specifications: Amplifier Type: Power Amplifier ; Applications: RF Microwave ; Frequency Range: 8500 to 9500 MHz ; Input VSWR: 1.8 1 ; Output VSWR: 1.8 1 ; Operating Temperature: -55 to 95 C (-67 to 203 F)
PD89-0040-08 : 800 MHz - 2500 MHz RF/MICROWAVE SPLITTER, 0.3 dB INSERTION LOSS Specifications: Frequency: 800.00 to 2500.00 MHz ; Insertion Loss: 0.30 dB
SW-223 : 0 MHz - 4000 MHz RF/MICROWAVE SGL POLE SGL THROW SWITCH, 1 dB INSERTION LOSS Specifications: Frequency Range: 0.0 to 4000 MHz ; Insertion Loss: 1 dB ; VSWR: 1.8 1 ; Impedance: 50 ohms ; Type: Single Pole Single Throw ; Operating Temperature: -55 to 85 C (-67 to 185 F)
SW-349RTR : 500 MHz - 1500 MHz RF/MICROWAVE SGL POLE SGL THROW SWITCH, 1.2 dB INSERTION LOSS Specifications: Frequency Range: 500 to 1500 MHz ; Insertion Loss: 1.2 dB ; VSWR: 1.7 1 ; Impedance: 50 ohms ; Type: Single Pole Single Throw ; Package Type: PLASTIC, SOIC-8 ; Operating Temperature: -40 to 85 C (-40 to 185 F)
2032-6347-00 : 7000 MHz - 11000 MHz RF/MICROWAVE 90 DEGREE HYBRID COUPLER Specifications: RF Coupler Type: 90 DEGREE HYBRID COUPLER ; Frequency Range: 7000.00 to 11000.00 MHz ; VSWR: 1.45 1
7700H-0021P : 2000 MHz - 8000 MHz RF/MICROWAVE LINEAR DETECTOR Specifications: Input Frequency Range: 2000 to 8000 MHz
7N251-A6 : 810 MHz - 826 MHz RF/MICROWAVE 3 PORT CIRCULATOR Specifications: Component: Circulator ; Frequency Range : 810 to 826 MHz ; Insertion Loss: 0.2000 dB ; VSWR: 1.2 1 ; Operating Temperature: -10 to 70 C (14 to 158 F)
1B0266-3 : = 90° / 180° Hybrid Couplers ;; Size LXWXH = 1.2 X 0.4 X 0.11" ;; Packaging = Caseless ;; Frequency MHZ = 1700-3400 ;; Power Handling Watts = 80.
AT002D6-31 : Digital Attenuator. GAAS 4 Bit Digital Attenuator. s Low DC Power Consumption s Attenuation 3 dB Steps 45 dB with High Accuracy s 14 Lead Hermetic Surface Mount Package s Capable of Meeting MIL-STD Requirements6 The is an MMIC FET digital attenuator consisting of four monolithic attenuators with an LSB 3 dB and a total attenuation 45 dB with all attenuators connected. This attenuator is recommended.
BR6589 : Frequency (MHz) = 5 - 500 ;; Gain (Typ/Min) (dB) = 26.5 / 25 ;; Noise Figure (Typ/Max) (dB) = 3.75 / 5 ;; P1dB Comp Point (Typ/Min) (dBm) = +22 / +20 ;; 3rd Order Intercept (Typ) (dBm) = +35 ;; 2nd Order Intercept (Typ) (dBm) = +55 ;; DC Power (Typ) (V/mA) = +15 / +130 ;; Package = Package = Package = 4 Pin TO-8B Package = Surface Mount Package = Connectorized.
BX5544 : Frequency (MHz) = 10 - 500 ;; Gain (Typ/Min) (dB) = 12.5 / 11 ;; Noise Figure (Typ/Max) (dB) = 2.5 / 3.5 ;; P1dB Comp Point (Typ/Min) (dBm) = +14.5 / +11.5 ;; 3rd Order Intercept (Typ) (dBm) = +27 ;; 2nd Order Intercept (Typ) (dBm) = +33 ;; DC Power (Typ) (V/mA) = +5 / +35 ;; Package = Package = Package = 4 Pin TO-8 Package = Surface Mount Package = Flatpack.
BX7379 : Frequency (MHz) = 5 - 200 ;; Gain (Typ/Min) (dB) = 14 / 12.5 ;; Noise Figure (Typ/Max) (dB) = 4.5 / 6 ;; P1dB Comp Point (Typ/Min) (dBm) = +23 / +21 ;; 3rd Order Intercept (Typ) (dBm) = +38 ;; 2nd Order Intercept (Typ) (dBm) = +47 ;; DC Power (Typ) (V/mA) = +12 / +88 ;; Package = Package = Package = 4 Pin TO-8 Package = Surface Mount Package = Flatpack.
DMF3929 : Chip on Board Mixer Quads. s High Volume Automatic Assembly s For Microwave MIC Assembly and Automated High Volume Manufacturing s Mechanically Rugged Design 100% DC Tested s Three Barrier Heights for Customized Mixer Performance Alpha's ceramic Chip on Board (COB) mixer quads are designed for high performance RF and microwave receiver applications. These devices utilize Alpha's.
FMM5815X : MMICs->GaAs MMICs. Millimeterwave Power Amplifiers. High Output Power: = 31dBm (Typ.) High Gain: = 21dB (Typ.) High PAE: add = 30% (Typ.) Impedance Matched Zin/Zout 50 0.25µm PHEMT Technology The is a high-gain, high linearity, 3-stage MMIC amplifier designed for operation in the17.5-20.0 GHz frequency range. This amplifier has an input and output designed for use in 50 systems.This device is well suited.
HMC224MS8 : GAAS Mmic Msop8 T/r Switch 5.0 - 6.0 GHZ. Low Cost 5-6 GHz Switch Ultra Small Package: MSOP8 High Input P1dB: +33 dBm Single Positive Supply: to +8V Typical Applications The HMC224MS8 is ideal for: UNII & HiperLAN PCMCIA WirelessLAN The is a low-cost SPDT switch an 8-lead MSOP package for use in transmitreceive applications. The device can control signals from to 6.0 GHz and is especially suited.
HMC412MS8G : +13 LO, Dbl-bal. Conversion Loss: 8.0 dB Noise Figure: 8.0 dB Input IP3: 17 dBm No External Components MSOP8G SMT Package Typical Applications Long Haul Radio Platforms Microwave Radio VSAT The is a passive double balanced mixer that operates between 9.0 GHz and 15 GHz. The HMC412MS8G operates with LO drive levels between +9 dBm and +13 dBm, and provides 8 dB conversion.
HPQ-05 : Power Splitter. Power Splitter. INSERTION LOSS, dB Avg. of Coupled Outputs less 3 dB excellent amplitude and phase unbalance good insertion loss good isolation excellent input and output VSWR excellent unit-to-unit repeatability small size applications image rejection mixer wideband amplifier matching I&Q modulator C. 1. HPQ models, aqueous washable. Environmental s and re-flow soldering.
LT5504 : Infrastructure. LT5504, 800MHz to 2.7GHz RF Measuring Receiver. RF Frequency Range: to 2.7GHz Ultra Wide Dynamic Range: 80dB Over Full Frequency Range and Over Temperature Wide Power Supply Range: to 5.25V Low Supply Current: at 3V Shutdown Current: 8-Lead MS0P Package RSSI Measurements Receive AGC Transmit Power Control ASK and Envelope Demodulation GSM/TDMA/CDMA/WCDMA The to 2700MHz monolithic integrated measuring.
M57716M : Silicon Bipolar Power Amplifier For 410-430MHz, 13W Digital Mobile.
MAALSS0013 : Satellite Radio Lna, 2.2 - 2.4 GHZ. Low Cost Plastic SOT-26 Package Adjustable Current Single to +5V Supply Voltage Output Power of +10 dBm Good 50 Input / Output Match M/A-COM's MAALSS0013 LNA is a GaAs MMIC low noise amplifier in a low-cost miniature SOT-26 surface mount plastic package. The MAALSS0013 employs a monolithic 2-stage design featuring a convenient 50 ohm input/output impedance.
MAATGM0001-DIE : Digital. 2.0-6.0GHz 6-bit Attenuator. to 6.0 GHz Operation 6 Bit Attenuator TTL Control Inputs Self-Aligned MSAG® MESFET Process The a 6-bit Attenuator with Parallel Input Control. This product is fully matched to 50 ohms on both the input and output. Each device 100% RF tested on wafer to ensure performance compliance. The part is fabricated using M/A-COM's repeatable, high performance.
STM961-15B : Hybrid Power Modules. RF Power Module Digital Cellular Applications. LINEAR POWER AMPLIFIER 915-960 MHz 26 VOLTS INPUT/OUTPUT 50 OHMS POUT = 42 dBm CW or PEP GAIN 30 dB The STM961-15B module is designed for digital cellular radio base station applications in the 915-960 MHz frequency range operating at 26V. The STM961-15B is designed to meet the low distortion, high linearity requirements of modern digital cellular base.
TGA4507 : GaAs. 27-32 GHZ Low Noise Amplifier. Typical Frequency Range: - 36 GHz 22 dB Nominal Gain 2.3 dB Nominal Noise Figure 12 dBm Nominal P1dB Bias um 3MI pHEMT Technology Chip Dimensions 0.004) in Point-to-Point Radio Point-to-MultiPoint Radio Ka Band VSAT Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process s. s are subject.
HMC581LP6 : The HMC581LP6 & HMC581LP6E are high linearity Dual Down Converter Receiver ICs that operate from 800 - 960 MHz and deliver a +26 dBm input third order intercept point for UMTS & GSM applications. The passive mixer outputs and high dynamic range IF amplifi er inputs are positioned so that an external IF fi lter can be placed in series between them. The converter.