Details, datasheet, quote on part number: SW90-0002
CategoryRF & Microwaves => Switches
DescriptionDC-4 Ghz, GAAS SPDT Switch, Absorptive, Single Supply
CompanyM/A-COM, Inc.
DatasheetDownload SW90-0002 datasheet
Find where to buy


Features, Applications
GaAs SPDT Switch, Absorptive, Single Supply, - 4 GHz

Operates - 4 GHz on Single Supply ASIC TTL / CMOS Driver Leadless 6 mm Chip Scale Plastic Package Low DC Power Consumption 50 Ohm Nominal Impedance Test Boards are Available Tape and Reel are Available


M/A-COM's is a SPDT absorptive pHEMT switch with integral TTL driver. This device in an MLP plastic surface mount package. This switch offers excellent broadband performance and repeatability from to 4 GHz, while maintaining low DC power dissipation. The SW90-0002 is ideally suited for wireless infrastructure applications.

Parameter Insertion Loss Isolation VSWR 1 dB Compression Input IP3 Switching Speed Test Conditions RFC--RF1,RF2 (Logic per truth table) RF1--RF2 (All Logic (RFC,RF1, RF2) (Logic per truth table) Off (RF1, RF2) (Logic per truth table) Two-tone inputs to +5 dBm Ton (50% Control to 10% RF) Toff (50% Control to 90% RF) Trise to 90% RF) Tfall to 10% RF) Vcc Logic "0" Logic "1" Icc

Sink Current 20 A max. Source Current 20 A max. Vcc min to max, Logic or "1" For guaranteed start-up Generated from DC-DC Converter with recommended capacitors

1. During turn-on, the device requires an initial start up current (Icc) specified as "Turn-on Current". Once operational, Icc will drop to the specified levels. 2. The DC-DC converter is guaranteed to start s as long as the power supplies have the maximum turn-on current available for start-up.

GaAs SPDT Switch, Absorptive, Single Supply, - 4 GHz Pin Configuration 3,4,5

Parameter Max. Input Power 0.05 GHz - 4.0 GHz Bias Voltages VCC Control Voltage 8 Operating Temperature Storage Temperature Absolute Maximum +27 dBm +34 dBm -0.5V to VCC to +125C

6. Operation of this device above any one of these parameters may cause permanent damage. 7. When the RF input is applied to the terminated port, the absolute maximum power is +30 dBm. 8. Standard CMOS TTL interface, latch-up will occur if logic signal is applied prior to power supply.

= No Connection 4. VEE is internally generated and must remain isolated from external power supplies. Generated noise is typical of switching DC-DC Converters. 5. Connections and external components shown in functional schematic are required. 0.1 F Capacitors need to be located near pins & 26.

Control Input Condition of the Switch RF Common to each RF Port C1 TTL Low RF1 Off "1" = TTL High RF2 On Off 9. Application Note C2083 is available on line at

M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit for additional data sheets and product information.

GaAs SPDT Switch, Absorptive, Single Supply, - 4 GHz Functional Schematic

10.Dual Supply Operation will eliminate the start-up current mentioned in Note 1. It will also eliminate spurious signals caused by the DC-DC converter that are present in single supply operation.


Related products with the same datasheet
Some Part number from the same manufacture M/A-COM, Inc.
SW90-0002-TB DC-4 Ghz, GAAS SPDT Switch, Absorptive, Single Supply
SW90-0003 DC-4 Ghz, GAAS SP4T Switch, Absorptive, Single Supply
SW90-0004 DC-4 Ghz, GAAS SP6T Switch, Absorptive, Single Supply
SW90-0004A  GaAs SP6T Switch, Absorptive, Single Supply, DC - 4 GHZ
SW90-0004TR DC-4 Ghz, GAAS SP6T Switch, Absorptive, Single Supply
SWD-109 Single/quad Driver For GAAS Fet Switche And Attenuator
SWD-109PIN Single/quad Drivers For GAAS Fet Switches And Attenuators
SWD-109RTR Single/quad Driver For GAAS Fet Switche And Attenuator
SWD-119PIN Single/quad Drivers For GAAS Fet Switches And Attenuators
SWD-119RTR Single/quad Driver For GAAS Fet Switche And Attenuator
T-1000  Two-Way Power Splitter/Combiner, 10 - 1000MHz
THV-50  Two-Way Power Splitter/Combiner, 2 - 200MHz
TP-101  RF Pulse Transformer, 500 KHZ - 1.5 GHZ
TP-102  RF Pulse Transformer, 1 - 500 MHZ
TP-103  RF Pulse Transformer, 500 KHZ - 1 GHZ
TP-104  RF Pulse Transformer, 750 KHZ - 400 MHZ
TP-105  RF Pulse Transformer
TP-108  RF Transformer, 350 - 1125 MHZ
TP-75  50/75-Ohm Transformer
TP-75N 50/75-ohm Transformer 2 - 200 MHZ
Same catergory

A77 : LNAs.  5 to 500 MHZ TO-8 Cascadable Amplifier. TO 500 MHz CASCADABLE AMPLIFIER HIGH GAIN: 16.5 dB (TYP.) HIGH OUTPUT LEVEL: +16.5 dBm (TYP.) HIGH THIRD ORDER I.P.: +30 dBm (TYP.) LOW VSWR: 1.3:1 (TYP.) Characteristics Frequency Small Signal Gain (min.) Gain Flatness (max.) Reverse Isolation Noise Figure (max.) Power Output 1 dB comp. (min.) IP3 IP2 Second Order Harmonic IP VSWR Input / Output (max.).

BX9115 : Frequency (MHz) = 5 - 1000 ;; Gain (Typ/Min) (dB) = 14.5 / 13 ;; Noise Figure (Typ/Max) (dB) = 4 / 5.5 ;; P1dB Comp Point (Typ/Min) (dBm) = +9.5 / +8 ;; 3rd Order Intercept (Typ) (dBm) = +23 ;; 2nd Order Intercept (Typ) (dBm) = +32 ;; DC Power (Typ) (V/mA) = +15 / +24 ;; Package = Package = Package = 4 Pin TO-8 Package = Surface Mount Package = Flatpack.

HMC239S8 : Industry-standard Soic8 SPDT Switch DC - 2.5 GHZ. Low Insertion Loss: 0.4 dB High Isolation: 35 dB Fast Switching Speed: 2ns High Input IP3: +50 dBm Typical Applications The HMC239S8 is ideal for: MMDS & WirelessLAN Basestation Infrastructure Portable Wireless The is a low-cost GaAs MMIC SPDT switch an 8-lead SOIC package. The switch can control signals from to 2.5 GHz. It is especially suited for low or medium.

JX503 : = Xinger Hybrid Couplers ;; Size LXWXH = 0.56 X 0.2 X 0.076" ;; Packaging = Surface Mount ;; Frequency MHZ = 2000-2300 ;; Power Handling Watts = 60.

MADCSM0011 :  Dual Mode Cellular Downconverter, 869 - 893 MHZ. Dual Mode Downconverter with LO Amplifier 3mm FQFP-N Plastic Package Operates over 5 V Supply Voltage High Gain: 12.5 dB Typical High Input Intercept Point: +8 dBm Typical Low Current Draw: 12 mA Typical Adjustable IP3 Level Low LO Drive Level: -10 dBm M/A-COM's MADCSM0011 integrated downconverter combines a downconverting mixer, an IF amplifier, a LO buffer.

PI5A4624 : Sotiny 1 Ohm, Low-Voltage, Single-supply SPDT Switch (Break-Before-Make).

RF2105L : High Power Linear UHF Amplifier. Typical Applications 900 MHz ISM Band Applications 400 MHz Industrial Radios Digital Communication Systems Product The is a high power, high efficiency linear amplifier IC. The device is manufactured on an advanced Gallium Arsenide Heterojunction Bipolar Transistor (HBT) process, and has been designed for use as the final RF amplifier in digital cellular.

RFP-100-1AMZ : = Attenuators ;; Size LXWXH = 0.975 X 0.375 X 0.2" ;; Packaging = Flanged ;; Frequency MHZ = 0-1000 ;; Power Handling Watts = 100.

SGA-4586 : DC-4000 MHZ Silicon Germanium HBT Cascadable Gain Block. Sirenza Microdevices is a high performance SiGe HBT MMIC Amplifier. A Darlington configuration featuring 1 micron emitters provides high F T and excellent thermal perfomance. The heterojunction increases breakdown voltage and minimizes leakage current between junctions. Cancellation of emitter junction non-linearities results in higher suppression of intermodulation.

ADL5523 : 400 MHz - 4 GHz Low Noise Amplifier The ADL5523 is a high performance GaAs pHEMT low-noise amplifier. It provides high gain and low noise figure for single down-conversion IF sampling receiver architectures as well as direct down conversion receivers. The ADL5523 amplifier comes in a compact, thermally enhanced 3 3 mm LFCSP package and operates over.

HMC392LC4 : GaAs PHEMT MMIC LOW NOISEc AMPLIFIER, 2 - 4 GHz The HMC609LC4 is a GaAs PHEMT MMIC Low Noise Amplifi er (LNA) which operates from 2 to 4 GHz. The HMC609LC4 extremely fl at performance characteristics including 20 dB of small signal gain, 3.5 dB of noise fi gure and output IP3 of +36.5 dBm across the operating band. This 50 Ohm matched amplifi er does.

HMC680LP4 : BiCMOS 5-Bit Digital Variable Gain Amplifier SMT, 30 - 400 MHz The HMC680LP4(E) is a digitally controlled variable gain amplifier which operates from 30 to 400 MHz, and can be programmed to provide -4 dB to +19 dB of gain, in 1 dB steps. The HMC680LP4(E) delivers noise figure of 5 dB in its maximum gain state, with output IP3 of up to +40 dBm in any state.

TDA8296 : Digital Global Standard Low IF Demodulator For Analog TV And FM Radio The TDA8296 is an alignment-free digital multistandard vision and sound low IF signal PLL demodulator for positive and negative video modulation including AM and FM mono sound processing. It can be used in all countries worldwide for M/N, B/G/H, I, D/K, L and L-accent standard. CVBS.

0-C     D-L     M-R     S-Z