|Category||RF & Microwaves => Switches|
|Description||GaAs SP6T Switch, Absorptive, Single Supply, DC - 4 GHZ|
|Datasheet||Download SW90-0004A datasheet
Operates - 4 GHz on Single Supply ASIC TTL / CMOS Driver Leadless 7 mm Chip Scale Plastic Package Low DC Power Consumption 50 Ohm Nominal Impedance Test Boards are Available Tape and Reel are AvailableDescription
M/A-COM's a SP6T absorptive pHEMT switch with integral TTL driver. This device in an MLP plastic surface mount package. This switch offers excellent broadband performance and repeatability from to 4 GHz, while maintaining low DC power dissipation. The SW90-0004A is ideally suited for wireless infrastructure applications.
Parameter Insertion Loss Isolation VSWR Test Conditions RFC-RF1, On (RFC, RF1-RF6) Logic per Truth Table Off (RF1-RF6) Logic per Truth Table Two-tone inputs to +5 dBm Ton (50% Control to 10% RF) Toff (50% Control to 90% RF) Trise to 90% RF) Tfall to 10% RF) Vcc Logic "0" Logic "1" Icc
Sink Current 20 µA max. Source Current 20 µA max. Vcc min to max, Logic or "1" For guaranteed start-up Generated from DC-DC Converter with recommended capacitors
1. During turn-on, the device requires an initial start up current (Icc) specified as "Turn-on Current". Once operational, Icc will drop to the specified levels. This is not applicable to dual supply operation. 2. The DC-DC converter is guaranteed to start µs as long as the power supplies have the maximum turn-on current available for start-up.GaAs SP6T Switch, Absorptive, Single Supply, - 4 GHz Pin Configuration
Function GND NC GND RFC GND RF4 GND RF5 GND RF6 GND NC VEE Vcc NC Vcc 7. 8. Parameter Max. Input Power 0.05 GHz - 4.0 GHz Bias Voltages VCC Control Voltage 8 Operating Temperature Storage Temperature
Operation of this device above any one of these parameters may cause permanent damage. When the RF input is applied to the terminated port, the absolute maximum power is +30 dBm. Standard CMOS TTL interface, latch-up will occur if logic signal is applied prior to power supply.
= No Connection 4. For single supply operation VEE is internally generated and must remain isolated from external power supplies. Generated noise is typical of switching DC-DC Converters. 5. Connections and external components shown in functional schematic are required. 0.1µF Capacitors need to be located near pins & 33.
M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information.
2 n North America: Tel. 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. 300 020GaAs SP6T Switch, Absorptive, Single Supply, - 4 GHz Functional Schematic
3 n North America: Tel. 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. 300 020
|Related products with the same datasheet|
|Some Part number from the same manufacture M/A-COM, Inc.|
|SW90-0004A-TB GaAs SP6T Switch, Absorptive, Single Supply, DC - 4 GHZ|
|SW90-0004TR DC-4 Ghz, GAAS SP6T Switch, Absorptive, Single Supply|
|SWD-109 Single/quad Driver For GAAS Fet Switche And Attenuator|
|SWD-109PIN Single/quad Drivers For GAAS Fet Switches And Attenuators|
|SWD-109RTR Single/quad Driver For GAAS Fet Switche And Attenuator|
|SWD-119PIN Single/quad Drivers For GAAS Fet Switches And Attenuators|
|SWD-119RTR Single/quad Driver For GAAS Fet Switche And Attenuator|
|T-1000 Two-Way Power Splitter/Combiner, 10 - 1000MHz|
|THV-50 Two-Way Power Splitter/Combiner, 2 - 200MHz|
|TP-101 RF Pulse Transformer, 500 KHZ - 1.5 GHZ|
|TP-102 RF Pulse Transformer, 1 - 500 MHZ|
|TP-103 RF Pulse Transformer, 500 KHZ - 1 GHZ|
|TP-104 RF Pulse Transformer, 750 KHZ - 400 MHZ|
|TP-105 RF Pulse Transformer|
|TP-108 RF Transformer, 350 - 1125 MHZ|
|TP-75 50/75-Ohm Transformer|
|TP-75N 50/75-ohm Transformer 2 - 200 MHZ|
|TP-75SMA 50/75-Ohm Transformer|
|TPX-75-4N 50/75-ohm Transformer 10 - 1500 MHZ|
EKIN2-150W : Modulators/Demodulators 140-160 Mhz,i/q Modulator
MA4P506-131 : Pin Diode Chips
SW-219PIN : GaAs SPDT RF Switch, DC - 3 GHZ
MA45266A-132 : L BAND, 2.2 pF, 60 V, SILICON, ABRUPT VARIABLE CAPACITANCE DIODE Specifications: Diode Type: VARIABLE CAPACITANCE DIODE
MA4EX585L-1225T : 4700 MHz - 6000 MHz RF/MICROWAVE DOUBLE BALANCED MIXER, 9.5 dB CONVERSION LOSS-MAX Specifications: Package Type: ROHS COMPLIANT, MINIATURE, PLASTIC, SOT-25, 5 PIN ; RF: 4700 to 6000 MHz ; Conversion Loss: 9.5 dB ; Mixer Type: Double Balanced ; Operating Temperature: -40 to 85 C (-40 to 185 F)
ML4513-97 : 30 V, GALLIUM ARSENIDE, ABRUPT VARIABLE CAPACITANCE DIODE Specifications: Diode Type: VARIABLE CAPACITANCE DIODE
ML6724-200 : 2000 MHz - 6000 MHz RF/MICROWAVE LIMITER Specifications: Limiter Type: Pin Diode Limiter ; Frequency Band: 2000.0 to 6000.0 MHz ; VSWR: 1.60 1
MLA2547-103B3 : 4400 MHz - 5000 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER Specifications: Amplifier Type: Power Amplifier ; Applications: RF Microwave ; Frequency Range: 4400 to 5000 MHz ; Input VSWR: 1.8 1 ; Output VSWR: 1.8 1 ; Operating Temperature: -55 to 95 C (-67 to 203 F)
2696-0108-4 : 2000 MHz - 4000 MHz, 0 deg - 180 deg RF/MICROWAVE DIGITALLY CONTROLLED PH SHFTR Specifications: Phase Shifter Type: Digital ; Frequency Range: 2000 to 4000 MHz ; Phase Shift Range: 180-deg, 1 ; Insertion Loss: 1.8 dB ; Input VSWR: 1.6 1
2955-2004 : 2000 MHz - 8000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS Specifications: Frequency Range: 2000 to 8000 MHz ; Insertion Loss: 2 dB ; VSWR: 1.7 1 ; Type: Single Pole Double Throw ; Operating Temperature: -55 to 95 C (-67 to 203 F)
8Q201 : 7100 MHz - 10000 MHz RF/MICROWAVE ISOLATOR Specifications: Component: Isolator ; Frequency Range : 7100 to 10000 MHz ; Insertion Loss: 1 dB ; VSWR: 1.15 1
1H0264-3 : = ;; Size LXWXH = 1.0 X 0.75 X 0.11" ;; Packaging = Caseless ;; Frequency MHZ = 440-880 ;; Power Handling Watts = 200.
3SK199 : RF Dual Gate FETs. VDS VGDS (VGDO) (V) = 13.5 ;; Id (mA) = 30 ;; PD (mW) = 150 ;; Idss (mA) = 0 to 0.1 ;; Yfs(Typ.) @1kHz (mS) = 21.5 ;; GRS(GCS*)/NF(NFCS*) (Typ.) (dB/dB) = 19.5/1.9 ;; Package = SMQ ;; Application = FM RF, Mixer.
AM42-0054 : L-band 2W Power Amplifier.
AMMC-6420 : 6-18 GHZ 1W Power Amplifier wide Frequency Range: 6-18 GHZ High Gain: 19 DB Partial Match Input And Output High Power (P-3dB): 30 DBM at 16 GHZ Integrated RF Power Detector ApplicationMicrowave Radio Systems LMDS And Point-to-point Millimeter Wave Long Haul Platforms Satellite Vsat, DBS Up/down Link 802.16 Broadband Wireless Access WLL And MMDS Loops.
BX9164 : Frequency (MHz) = 10 - 1200 ;; Gain (Typ/Min) (dB) = 26 / 24 ;; Noise Figure (Typ/Max) (dB) = 3.6 / 4.5 ;; P1dB Comp Point (Typ/Min) (dBm) = +8.5 / +6.5 ;; 3rd Order Intercept (Typ) (dBm) = +20 ;; 2nd Order Intercept (Typ) (dBm) = +33 ;; DC Power (Typ) (V/mA) = +15 / +35 ;; Package = Package = Package = 4 Pin TO-8 Package = Surface Mount Package = Flatpack.
BX9701 : Frequency (MHz) = 200 - 2000 ;; Gain (Typ/Min) (dB) = 12 / 11 ;; Noise Figure (Typ/Max) (dB) = 3 / 4 ;; P1dB Comp Point (Typ/Min) (dBm) = +14 / +13 ;; 3rd Order Intercept (Typ) (dBm) = +25 ;; 2nd Order Intercept (Typ) (dBm) = +32 ;; DC Power (Typ) (V/mA) = +5 / +48 ;; Package = Package = Package = 4 Pin TO-8 Package = Surface Mount Package = Flatpack.
DA0886 : 10-1000MHz GAAS 6 Section Attenuator.
F1220 : Power. Pout W = 20 ;; Freq MHZ = 175 ;; Gain DB = 10 ;; Theta JC = 1.95 ;; GM Mho = 1.6 ;; Idsat a = 15 ;; Ciss PF = 80 ;; CRSS PF = 12 ;; Coss PF = 60 ;; Die = 2 ;; Style = Single Ended ;; PKG = aa.
KF446AV : = 400MHz Band(50ohm) ;; Package = SC-44.
MABAES0032 : E-Series SMT Low Cost 1:1 RF Transformer 5 - 1000 MHZ. Surface Mount 1:1 Impedance Ratio CT on Secondary Available on Tape and Reel M/A-COM's 1:1 RF transformer in a low cost, surface mount package. Ideally suited for high volume cellular wireless applications. Typical applications include single to balanced mode conversion and impedance matching. Parameter Frequency Range Insertion Loss - 300 MHz 300-1000.
MAX1459 : 2-wire, 4-20ma Smart Signal Conditioner. o Highly Integrated Sensor Signal Conditioner for 2-Wire, 420mA Transmitters o Sensor Errors Trimmed Using Correction Coefficients Stored in Internal EEPROM-- Eliminates the Need for Laser Trimming and Potentiometers o Compensates Offset, Offset TC, FSO, FSOTC, FSO Linearity o Programmable Current Source to 2.0mA) for Sensor Excitation o Fast Signal-Path.
PT2243 : Remote Control Transmitter. PT2243 is an Infrared Remote Control Transmitter Utilizing CMOS Technology Specially Designed For Electrical Appliances Such as Audio System, Television, Video Cassette Recorder, CD Player And Others..
RF3118 : LNAs. 3V 1900MHz Linear Amplifier Module. Typical Applications 3V CDMA US-PCS Handsets 3V CDMA2000/1X PCS Handsets Compatible with Qualcomm Chipset Spread-Spectrum Systems The is a high-power, high-efficiency linear amplifier IC targeting 3V handheld systems. The device is manufactured on an advanced Gallium Arsenide Heterojunction Bipolar Transistor (HBT) process, and has been designed for use as the final.
SM401 : Power. Pout W = 135 ;; Freq MHZ = 175 ;; Gain DB = 11 ;; Theta JC = 0.65 ;; GM Mho = 7.2 ;; Idsat a = 42 ;; Ciss PF = 300 ;; CRSS PF = 15 ;; Coss PF = 200 ;; Die = 1 ;; Style = Single Ended ;; PKG = am ;; = P ;; = a ;; = S.
UPC8101GR : 150 MHZ Silicon Quadrature Modulator ic For Digital Mobile Communications.
HMC-C045 : LOW NOISE AMPLIFIER The HMC-C045 is a GaAs MMIC PHEMT Low Noise Amplifi er in a miniature, hermetic module which operates between 1.8 and 4.2 GHz. This high dynamic range low noise amplifi er module provides 26 dB of gain, sub-1 dB noise fi gure and up to +26 dBm of output IP3 while operating from a single positive supply between +8V and +15V. The amplifi.
HMC753LP4E : Low Noise Amplifier SMT, 1 - 11 GHz The HMC753LP4E is a GaAs MMIC Low Noise Wideband Amplifier housed in a leadless 4x4 mm plastic surface mount package. The amplifier operates between 1 and 11 GHz, providing up to 16.5 dB of small signal gain, 1.5 dB noise figure, and output IP3 of +30 dBm, while requiring only 55 mA from a +5V supply. The P1dB output.
HMC869LC5 : I/Q Receiver SMT, 12 - 16 GHz The HMC869LC5 is a GaAs MCM I/Q downconverter in a leadless RoHS compliant SMT package. This device provides a small signal conversion gain of 14 dB with a noise figure of 2.8 dB and 32 dB of image rejection. The HMC869LC5 utilizes an LNA followed by an image reject mixer which is driven by an LO buffer amplifier. The image.
SST12LP18E : 2.4 GHz High-Power, High-Gain Power Amplifier Please consider this device: SST12LP19E. View Side By Side Comparison The SST12LP18E is a versatile power amplifier based on the highly-reliable InGaP/GaAs HBT technology. The SST12LP19E can be easily configured for high-power applications with good power-added efficiency while operating over the 2.4- 2.5 GHz frequency.
MMZ09312BT1 : Heterojunction Bipolar Transistor Technology (InGaP HBT) TheMMZ09312B is a 2--stage high efficiency, Class AB InGaP HBT amplifier designed for use as a linear driver amplifier in wireless base station applications as well as an output stage in femtocell or repeater applications. It is suitable for applications with frequencies from 400 to 1000 MHz such.