|
|
Part: MAX4201EVKIT
Category:
Others
Description: Evaluation Kit: Max4200/max4201/max4202
Company: Maxim Integrated Products
Datasheet: Download MAX4201EVKIT datasheet File size : 449 kB
Request For quote: Find where to buy MAX4201EVKIT
Datasheet text preview:
19-1351; Rev 0; 3/98
MAX4201 Evaluation Kit
________________General Description
The MAX4201 evaluation kit (EV kit) simplifies evaluation of the MAX4201 ultra-high-speed, low-power, lownoise, open-loop buffer. The EV kit circuit demonstrates the MAX4201 in the noninverting unity-gain configuration. RF-style connectors (SMA) and 50 terminating resistors are included for test equipment compatibility. This EV kit can also be used to evaluate the MAX4200 and MAX4202 (contact Maxim for free samples). Note that the MAX4201 has an internal 50 output termination resistor, and the MAX4202 has an internal 75 outp u t termination resistor, while the MAX4200 has no i n t e r n a l output termination resistor (refer to the MAX4200MAX4205 data sheet for more information).
____________________________Features
o 780MHz -3dB Bandwidth o 280MHz 0.1dB Gain Flatness o 2.1nV/Hz Voltage Noise Density o 0.8pA /Hz Current Noise Density o 4200V/µs Slew Rate o Excellent Capacitive-Load-Driving Capability o Fully Assembled and Tested Surface-Mount Board
Evaluates: MAX4200/MAX4201/MAX4202
Component List
DESIGNATION QTY C1, C3 C2, C4 IN, OUT R1 R2 U1 None None 2 2 2 1 1 1 1 1 DESCRIPTION 10µF, 10V, 20% tantalum capacitors AVX TAJB106M010 or Sprague 293D106X0010B 0.1µF, 10% ceramic capacitors SMA connectors 49.9, 1% resistor 0 resistor MAX4201ESA MAX4201 PC board MAX4200MAX4205 data sheet
_______________Ordering Information
PART MAX4201EVKIT TEMP. RANGE -40°C to +85°C IC PACKAGE 8 SO
_________________________Quick Start
The MAX4201 EV kit is fully assembled and tested. Follow these steps to verify board operation. Do not turn on the power supply until all connections are completed. 1) The circuit requires supply voltages of ±4.0V to ± 5 . 5 V . For evaluation purposes, connect a +5V supply to the pad labeled VCC and a -5V supply to the pad labeled VEE. Connect the power-supply grounds to the pad marked GND. 2) Connect the output marked OUT to an oscilloscope through a terminated 50 cable. 3) Turn on the power supply. Apply a signal of ±3.3V maximum to the SMA connector marked IN+. 4) Verify the output signal on the oscilloscope. (Note: When using a 50 terminated oscilloscope input, the output amplitude observed on the oscilloscope will be half that on the input. This is due to the voltage divider formed by the internal 50 back-terminating resistor and the oscilloscope input termination impedance.)
__________________Component Suppliers
SUPPLIER AVX SPRAGUE PHONE (803) 946-0690 (603) 224-1961 FAX (803) 626-3123 (603) 224-1430
Note: Please indicate that you are using the MAX4201 when contacting these component suppliers.
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468.
MAX4201 Evaluation Kit Evaluates: MAX4200/MAX4201/MAX4202
_______________Detailed Description
Layout Considerations
T h e MAX4201 EV kit layout has been optimized for high-speed signals and low distortion with careful attention given to grounding, power-supply bypassing, and signal-path layout. The small, surface-mount, ceramic bypass capacitors (C2, C4) have been placed as close to the MAX4201 supply pins as possible. A continuous g r o u n d plane has been maintained under the IC to reduce inductance to the signal return path. When using the MAX4200, replace R2 with an appropriate terminating resistor.
1
N.C.
N.C.
8
U1
2 N.C. VCC 7 C2 0.1µF C1 10µF 10V
VCC
MAX4201
IN R1 49.9
3
IN RT 50
OUT
6 R2 0
OUT
VEE
4 C3 10µF 10V C4 0.1µF
VEE
N.C.
5
GND
Figure 1. MAX4201 EV Kit Schematic
2
_______________________________________________________________________________________
MAX4201 Evaluation Kit Evaluates: MAX4200/MAX4201/MAX4202
1.0"
1.0"
Figure 2. MAX4201 EV Kit Component Placement Guide
Figure 3. MAX4201 EV Kit PC Board Layout--Component Side
1.0"
Figure 4. MAX4201 EV Kit PC Board Layout--Solder Side
_______________________________________________________________________________________
3
Others parts begin by ma
|
|
|
