Digchip : Database on electronics components
Electronics components database



Details, datasheet, quote on part number: MAX6954
 
 
Part numberMAX6954
CategoryOptoelectronics => Drivers/Controllers
DescriptionMAX6954 4-Wire Interfaced, 2.7V to 5.5V Led Display Driver With I/o Expander And Key Scan
CompanyMaxim Integrated Products
DatasheetDownload MAX6954 datasheet
 


 
Specifications, Features, Applications

4-Wire Interfaced, to 5.5V LED Display Driver with I/O Expander and Key Scan

The is a compact display driver that interfaces microprocessors to a mix 7-segment, 14-segment, and 16-segment LED displays through an SPITMor QSPITM-compatible 4-wire serial interface. The serial interface may be cascaded through multiple devices. The MAX6954 drives to 16 digits 7-segment, 8 digits 14-segment, 8 digits or 128 discrete LEDs, while functioning from a supply voltage as low as 2.7V. The driver includes five I/O expander (or GPIO) lines, some or all or which may be configured as a keyswitch reader, which automatically scans and debounces a matrix to 32 switches. Included on chip are full 14- and 16-segment ASCII 104-character fonts, a hexadecimal font for 7-segment displays, multiplex scan circuitry, anode and cathode drivers, and static RAM that stores each digit. The maximum segment current for the display digits is set using a single external resistor. Digit intensity can be independently adjusted using the 16-step internal digital brightness control. The MAX6954 includes a low-power shutdown mode, a scan-limit register that allows the user to display from to 16 digits, segment blinking (synchronized across multiple drivers, if desired), and a test mode, which forces all LEDs on. The LED drivers are slew-rate limited to reduce EMI. For a 2-wire interfaced version, refer to the MAX6955* data sheet. An evaluation kit* (EV kit) for the MAX6955 is available.

Features

o High-Speed 26MHz SPI/QSPI/MICROWIRETMCompatible Serial Interface to 5.5V Operation o Drives to 16 Digits 7-Segment, 8 Digits 14-Segment, 8 Digits 16-Segment, 128 Discrete LEDs, or a Combination of Digit Types o Drives Common-Cathode Monocolor and Bicolor LED Displays o Built-In ASCII 104-Character Font for 14-Segment and 16-Segment Digits and Hexadecimal Font for 7-Segment Digits o Automatic Blinking Control for each Segment o 10A (typ) Low-Power Shutdown (Data Retained) o 16-Step Digit-by-Digit Digital Brightness Control o Display Blanked on Power-Up o Slew-Rate Limited Segment Drivers for Lower EMI o Five GPIO Port Pins Can Be Configured as KeySwitch Reader to Scan and Debounce to 32 Switches with n-Key Rollover o IRQ Output when a Key Input Is Debounced o 36-Pin SSOP and 40-Pin DIP Packages o Automotive Temperature Range Standard

GPIO AND KEY-SCAN CONTROL ISET CURRENT SOURCE PWM BRIGHTNESS CONTROL DIGIT MULTIPLEXER TO P4
Applications
Set-Top Boxes Panel Meters White Goods Automotive Bar Graph Displays Audio/Video Equipment
PART MAX6954AAX MAX6954APL TEMP RANGE to +125C PIN-PACKAGE 36 SSOP 40 PDIP

Pin Configurations and Typical Operating Circuits appear at end of data sheet. SPI and QSPI are trademarks of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor Corp.

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com.

4-Wire Interfaced, to 5.5V LED Display Driver with I/O Expander and Key Scan MAX6954

Voltage (with Respect to GND) to +6V All Other Pins............................................-0.3V to (V+ + 0.3V) Current O0O7 Sink Current......................................................935mA O0O18 Source Current.................................................55mA DIN, CLK, CS, OSC, DOUT, BLINK, OSC_OUT, P4...........................................................40mA GND.....................................................................................1A Continuous Power Dissipation (TA +70C) 36-Pin SSOP (derate at 11.8mW/C above +70C).....941mW 40-Pin PDIP (derate at 16.7mW/C above +70C).....1333mW Operating Temperature Range (TMIN to +125C Junction Temperature......................................................+150C Storage Temperature to +150C Lead Temperature (soldering, 10s).................................+300C

Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

(Typical Operating Circuit, TA = TMIN to TMAX, unless otherwise noted.) (Note 1)

PARAMETER Operating Supply Voltage SYMBOL V+ Shutdown mode, all digital inputs V+ or GND All segments on, all digits scanned, intensity set to full, internal oscillator, DOUT open circuit, no display or OSC_OUT load connected TA = TMIN to TMAX CONDITIONS MIN 2.7 10 TYP MAX A 40 UNITS V

Master Clock Frequency Dead Clock Protection Frequency OSC Internal/External Detection Threshold OSC High Time OSC Low Time Slow Segment Blink Period Fast Segment Blink Period Fast or Slow Segment Blink Duty Cycle

OSC = RC oscillator, RSET = 56k, fSLOWBLINK C SET = 3.3V fFASTBLINK OSC = RC oscillator, RSET = 56k, CSET = 3.3V

4-Wire Interfaced, to 5.5V LED Display Driver with I/O Expander and Key Scan
(Typical Operating Circuit, TA = TMIN to TMAX, unless otherwise noted.) (Note 1)

PARAMETER Segment Drive Source Current Segment Current Slew Rate Segment Drive Current Matching LOGIC INPUTS AND OUTPUTS Input Leakage Current DIN, CLK, CS, OSC, P4 4-Wire Logic-High Input Voltage DIN, CLK, CS 4-Wire Logic-Low Input Voltage DIN, CLK, CS Port Logic-High Input Voltage P3, P4 Port Logic-Low Input Voltage P3, P4 Port Hysteresis Voltage P3, P4 Port Input Pullup Current from V+ Port Output Low Voltage Blink Output Low Voltage DOUT Output High Voltage DOUT Output Low Voltage OSC_OUT Output High Voltage OSC_OUT Output Low Voltage IIH, IIL +1 A SYMBOL ISEG ISEG/ t ISEG VLED = 3.3V CONDITIONS = +25C MIN -34.5 TYP MAX -46.5 UNITS mA mA/s %

VIHSPI VILSPI VIHP VILP VIP IIPU VOLP VOLBK VOHDO VOLDO VOHOSC VOLOSC to P3 configured as keyscan input, = 3.3V ISINK = 8mA ISINK = 0.6mA ISOURCE = 1.6mA ISINK = 1.6mA ISOURCE = 1.6mA ISINK = 1.6mA




Related products with the same datasheet
MAX6954AAX   MAX6954APL  


Some Part number from the same manufacture Maxim Integrated Products
MAX6954AAX MAX6954 4-Wire Interfaced, 2.7V to 5.5V Led Display Driver With I/o Expander And Key Scan
MAX6955 MAX6955 2-Wire Interfaced, 2.7V to 5.5V Led Display Driver With I/o Expander And Key Scan
MAX6955EVKIT MAX6955EVKIT Evaluation Kit For The MAX6955
MAX6956 MAX6956 2-Wire-Interfaced, 2.5V to 5.5V, 20-Port or 28-Port Led Display Driver And I/o Expander
MAX6957 MAX6957 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port And 28-Port Led Display Driver And I/o Expander
MAX6958 MAX6958, MAX6959 2-Wire Interfaced, 3V to 5.5V, 4-Digit, 9-Segment Led Display Drivers With Keyscan
MAX695AC -
MAX695C/D Microprocessor Supervisory Circuits
MAX695E -
MAX695EJE Microprocessor Supervisory Circuits
MAX695M -
MAX695MJE Microprocessor Supervisory Circuits
MAX695MJE/883B Microprocessor Supervisory Circuit
MAX696 P Supervisor With Battery Switchover And Programmable Reset
MAX6964 17-Output Led Driver/gpo With Intensity Control And Hot-insertion Protection
MAX6965 9-Output Led Driver With Intensity Control <<<>>>The MAX6965 I2C -compatible Serial Interfaced Peripheral Provides Microprocessors With Nine Additional Output Ports. Each Output is an Open-drain Current-sinking
MAX696C P Supervisor With Battery Switchover And Programmable Reset
MAX696C/D Microprocessor Supervisory Circuits
MAX696E P Supervisor With Battery Switchover And Programmable Reset
MAX696EJE Microprocessor Supervisory Circuits
MAX696M P Supervisor With Battery Switchover And Programmable Reset