|
Details, datasheet, quote on part number:DL4735
| |
| Part: | DL4735 |
| Category: | Discrete => Diodes & Rectifiers => Zener Diodes |
| Description: | Package Type : Glass Melf, PD : 1.0W, VZ : 6.2V |
| Company: | Micro Commercial Components |
| Datasheet: | Download DL4735 datasheet File size : 107 kB |
| Request For quote: | Find where to buy DL4735
|
| |
Datasheet text preview:
MCC
Features
· · · ·
omponents 20736 Marilla Street Chatsworth !"# $
% !"#
DL4728 THRU DL4756
1.0 Watt Zener Diode 3.3 to 47 Volts
GLASS MELF
Cathode Mark
Wide Voltage Range Available Glass Package High Temp Soldering: 260°C for 10 Seconds At Terminals For Surface Mount Applications
Maximum Ratings
· · · · · Operating Temperature: -55°C to +150°C Storage Temperature: -55°C to +150°C 1 Watt DC Power Dissipation Power Derating: 10.0mW/°C above 100°C Maximum Forward Voltage @ 200mA: 1.2 Volts
Figure 1 - Typical Temperature Coefficient
C
B
40
A
mV/°C 20
0
0
20 VZ
40
DIM A B C
INCHES MIN .190 --.095
MAX .205 .022 .105
MM MIN 4.80 --2.40
MAX 5.20 .55 2.67
NOTE Nominal
Typical Temperature Coefficient (mV/°C) versus Zener Voltage (VZ) Figure 2 - Derating Curve
SUGGESTED SOLDER PAD LAYOUT
.210"
1.0 W 0.5
.115"
.035"
100 150 200 Temperature °C Power Dissipation (W) - Versus - Temperature °C 25
Revision: 3
www.mccsemi.com
2003/01/07
DL4728 thru DL4756
ELECTRICAL CHARACTERISTICS @25°C
MCC PART NUMBER ZENER VOLTAGE VZ TEST CURRENT I ZT MAXIMUM DYNAMIC IMPEDANCE Z Z T @ IZ T OHMS 10 10 9 9 8 7 5 2 3.5 4.0 4.5 5.0 7 8 9 10 14 16 20 22 23 25 35 40 45 50 60 70 80 MAXIMUM REVERSE CURRENT I R @ VR µA 100 100 50 10 10 10 10 10 10 10 10 10 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 TEST VOLTAGE VR MAXIMUM REGULATOR CURRENT IZM TA = 50°C mA 276 252 234 217 193 178 162 146 133 121 110 100 91 83 76 69 61 57 50 45 41 38 34 30 27 25 23 22 19
MCC
MAXIMUM KNEE IMPEDANCE Z ZK @ IZK OHMS 400 400 400 400 500 550 600 700 700 700 700 700 700 700 700 700 700 700 750 750 750 750 750 1000 1000 1000 1000 1500 1500 TEST CURRENT I ZK MAXIMUM SURGE CURRENT IS mA 1380 1260 1190 1070 970 890 810 730 660 605 550 500 454 414 380 344 304 285 250 225 205 190 170 150 135 125 115 110 95
VOLTS DL4728 DL4729 DL4730 DL4731 DL4732 DL4733 DL4734 DL4735 DL4736 DL4737 DL4738 DL4739 DL4740 DL4741 DL4742 DL4743 DL4744 DL4745 DL4746 DL4747 DL4748 DL4749 DL4750 DL4751 DL4752 DL4753 DL4754 DL4755 DL4756 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47
mA 76 69 64 58 53 49 45 41 37 34 31 28 25 23 21 19 17 15.5 14 12.5 11.5 10.5 9.5 8.5 7.5 7.0 6.5 6.0 5.5
VOLTS 1 1 1 1 1 1 2 3 4 5 6 7 7.6 8.4 9.1 9.9 11.4 12.2 13.7 15.2 16.7 18.2 20.6 22.8 25.1 27.4 29.7 32.7 35.8
mA 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.5 0.5 0.5 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25
NOTE 1 The JEDEC type numbers shown have A 5% tolerance on nominal zener voltage. No suffix signifies A 10% tolerance, C signifies 2%, and D signifies 1% tolerance. NOTE 2 The zener impedance is derived from the 60Hz AC voltage, which results when an AC current having an rms value equal to 10% of the DC zener current (Izt or Izk) is superimposed on Izt or Izk. Zener impedance is measured at two points to insure a sharp knee on the breakdown curve and eliminate unstable units. NOTE 3 The reverse surge current is measured at 25oC ambient using a 1/2 square wave or equivalent sine wave pulse 1/120 second duration superimposed on Izt NOTE 4 Voltage measurements to be performed 90 seconds after application of DC current.
Revision: 3
www.mccsemi.com
2003/01/07
|
|
