|
Details, datasheet, quote on part number:24C16B-ESL
| |
Datasheet text preview:
24C08B/16B
8K/16K 5.0V I2CTM Serial EEPROMs
FEATURES
· Single supply with operation from 4.5-5.5V · Low power CMOS technology - 1 mA active current typical - 10 µA standby current typical at 5.5V · Organized as 4 or 8 blocks of 256 bytes (4 x 256 x 8) or (8 x 256 x 8) · 2-wire serial interface bus, I2CTM compatible · Schmitt trigger, filtered inputs for noise suppression · Output slope control to eliminate ground bounce · 100 kHz compatibility · Self-timed write cycle (including auto-erase) · Page-write buffer for up to 16 bytes · 2 ms typical write cycle time for page-write · Hardware write protect for entire memory · Can be operated as a serial ROM · ESD protection > 4,000V · 1,000,000 ERASE/WRITE cycles guaranteed · Data retention > 200 years · 8-pin DIP, 8-lead or 14-lead SOIC packages · Available for extended temperature range - Automotive (E): -40°C to +125°C
PACKAGE TYPES
PDIP A0 A1 A2 VSS 1 24C08B/16B 2 3 4 8 7 6 5 VCC WP SCL SDA
8-lead SOIC
A0 A1 A2 VSS
1
24C08B/16B
8 7 6 5
VCC WP SCL SDA
2 3 4
14-lead SOIC
NC A0 A1 NC A2 VSS NC
1 2 3 4 5 6 7
14 13
NC VCC WP NC SCL SDA NC
24C08B/16B
12 11 10 9 8
DESCRIPTION
The Microchip Technology Inc. 24C08B/16B is an 8K or 16K bit Electrically Erasable PROM intended for use in extended/automotive temperature ranges. The device is organized as four or eight blocks of 256 x 8-bit memory with a 2-wire serial interface. The 24C08B/16B also has a page-write capability for up to 16 bytes of data. The 24C08B/16B is available in the standard 8-pin DIP and both 8-lead and 14-lead surface mount SOIC packages.
BLOCK DIAGRAM
WP HV GENERATOR
I/O CONTROL LOGIC
MEMORY CONTROL LOGIC
XDEC
EEPROM ARRAY PAGE LATCHES
SDA
SCL YDEC
VCC VSS
SENSE AMP R/W CONTROL
I2C is a trademark of Philips Corporation.
© 1996 Microchip Technology Inc.
DS21081D-page 1
This document was created with FrameMaker 4 0 4
24C08B/16B
1.0
1.1
ELECTRICAL CHARACTERISTICS
Maximum Ratings*
TABLE 1-1:
Name VSS SDA SCL WP VCC A0, A1, A2
PIN FUNCTION TABLE
Function Ground Serial Address/Data I/O Serial Clock Write Protect Input +4.5V to 5.5V Power Supply No Internal Connection
VCC..7.0V All inputs and outputs w.r.t. VSS ...... -0.6V to VCC +1.0V Storage temperature .... -65°C to +150°C Ambient temp. with power applied ....... -65°C to +125°C Soldering temperature of leads (10 seconds) .... +300°C ESD protection on all pins ........ 4 kV
*Notice: Stresses above those listed under "Maximum ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.
TABLE 1-2:
DC CHARACTERISTICS
VCC = +4.5V to +5.5V Automotive (E): Tamb = -40°C to +125°C Parameter Symbol VIH VIL VHYS VOL ILI ILO CIN, COUT ICC write ICC read ICCS Min .7 Vcc -- .05 Vcc -- -10 -10 -- -- -- -- Max -- .3 VCC -- .40 10 10 10 3 1 100 Units V V V V µA µA pF mA mA µA Conditions
WP, SCL and SDA pins: High level input voltage Low Level input voltage Hysteresis of Schmitt trigger inputs Low level output voltage Input leakage current Output leakage current Pin capacitance (all inputs/outputs) Operating current Standby current
Note:
(Note) IOL = 3.0 mA, VCC=4.5V VIN =.1V to VCC VOUT = .1V to VCC VCC = 5.0V (Note 1) Tamb = 25°C, FCLK=1 MHz VCC = 5.5V, SCL = 400 kHz VCC = 5.5V, SDA = SCL = VCC
This parameter is periodically sampled and not 100% tested.
FIGURE 1-1:
BUS TIMING START/STOP
VHYS
SCL TSU:STA SDA THD:STA TSU:STO
START
STOP
DS21081D-page 2
© 1996 Microchip Technology Inc.
24C08B/16B
TABLE 1-3: AC CHARACTERISTICS
Symbol FCLK THIGH TLOW TR TF THD:STA TSU:STA THD:DAT TSU:DAT TSU:STO TAA TBUF TOF TSP TWR -- -- Min -- 4000 4700 -- -- 4000 4700 0 250 4000 -- 4700 -- -- -- 1M 10M Max 100 -- -- 1000 300 -- -- -- -- -- 3500 -- 250 50 10 -- -- Units kHz ns ns ns ns ns ns ns ns ns ns ns ns ns ms cycles Remarks
Parameter Clock frequency Clock high time Clock low time SDA and SCL rise time SDA and SCL fall time START condition hold time START condition setup time Data input hold time Data input setup time STOP condition setup time Output valid from clock Bus free time Output fall time from VIH min to VIL max Input filter spike suppression (SDA and SCL pins) Write cycle time Endurance 24C08B 24C16B
(Note1) (Note 1) After this period the first clock pulse is generated Only relevant for repeated START condition
(Note 2) Time the bus must be free before a new transmission can start (Note 1), CB 100 pF (Note 3) Byte or Page mode 25°C, VCC = 5.0V, Block Mode (Note 4)
Note 1: Not 100% tested. CB = total capacitance of one bus line in pF. 2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 3: The combined TSP and VHYS specifications are due to new Schmitt trigger inputs which provide improved noise and spike suppression. This eliminates the need for a TI specification. 4: This parameter is not tested but guaranteed by characterization. For endurance estimates in a specific application, please consult the Total Endurance Model which can be obtained on our BBS or website.
FIGURE 1-2:
BUS TIMING DATA
TF THIGH TLOW TR
SCL TSU:STA SDA IN THD:STA TSP TAA TBUF THD:DAT TSU:DAT TSU:STO
TAA SDA OUT
THD:STA
© 1996 Microchip Technology Inc.
DS21081D-page 3
24C08B/16B
2.0 FUNCTIONAL DESCRIPTION
3.4 Data Valid (D)
The 24C08B/16B supports a Bi-directional 2-wire bus and data transmission protocol. A device that sends data onto the bus is defined as transmitter, and a device receiving data as receiver. The bus has to be controlled by a master device which generates the serial clock (SCL), controls the bus access, and generates the START and STOP conditions, while the 24C08B/16B works as slave. Both, master and slave can operate as transmitter or receiver but the master device determines which mode is activated. The state of the data line represents valid data when, after a START condition, the data line is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed during the LOW period of the clock signal. There is one clock pulse per bit of data. Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of the data bytes transferred between the START and STOP conditions is determined by the master device and is theoretically unlimited, although only the last 16 will be stored when doing a write operation. When an overwrite does occur it will replace data in a first in first out fashion.
3.0
BUS CHARACTERISTICS
The following bus protocol has been defined: · Data transfer may be initiated only when the bus is not busy. · During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in the data line while the clock line is HIGH will be interpreted as a START or STOP condition. Accordingly, the following bus conditions have been defined (Figure 3-1).
3.5
Acknowledge
Each receiving device, when addressed, is obliged to generate an acknowledge after the reception of each byte. The master device must generate an extra clock pulse which is associated with this acknowledge bit. Note: The 24C08B/16B does not generate any acknowledge bits if an internal programming cycle is in progress.
3.1
Bus not Busy (A)
Both data and clock lines remain HIGH.
3.2
Start Data Transfer (B)
A HIGH to LOW transition of the SDA line while the clock (SCL) is HIGH determines a START condition. All commands must be preceded by a START condition.
3.3
Stop Data Transfer (C)
A LOW to HIGH transition of the SDA line while the clock (SCL) is HIGH determines a STOP condition. All operations must be ended with a STOP condition.
The device that acknowledges, has to pull down the SDA line during the acknowledge clock pulse in such a way that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse. Of course, setup and hold times must be taken into account. During reads, a master must signal an end of data to the slave by NOT generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case, the slave (24C08B/16B) will leave the data line HIGH to enable the master to generate the STOP condition.
FIGURE 3-1:
(A) (B)
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
(D) (D) (C) (A)
SCL
SDA
START CONDITION
ADDRESS OR ACKNOWLEDGE VALID
DATA ALLOWED TO CHANGE
STOP CONDITION
DS21081D-page 4
© 1996 Microchip Technology Inc.
24C08B/16B
3.6 Device Addressing
4.0
4.1
WRITE OPERATION
Byte Write
A control byte is the first byte received following the start condition from the master device. The control byte consists of a 4-bit control code, for the 24C08B/16B this is set as 1010 binary for read and write operations. The next three bits of the control byte are the block select bits (B2, B1, B0). They are used by the master device to select which of the eight 256 word blocks of memory are to be accessed. These bits are in effect the three most significant bits of the word address. The last bit of the control byte defines the operation to be performed. When set to one a read operation is selected, when set to zero a write operation is selected. Following the start condition, the 24C08B/16B monitors the SDA bus checking the device type identifier being transmitted, upon a 1010 code the slave device outputs an acknowledge signal on the SDA line. Depending on the state of the R/W bit, the 24C08B/16B will select a read or write operation. Operation Read Write Control Code 1010 1010 Block Select Block Address Block Address R/W 1 0
Following the start condition from the master, the device code (4 bits), the block address (3 bits), and the R/W bit which is a logic low is placed onto the bus by the master transmitter. This indicates to the addressed slave receiver that a byte with a word address will follow after it has generated an acknowledge bit during the ninth clock cycle. Therefore the next byte transmitted by the master is the word address and will be written into the address pointer of the 24C08B/16B. After receiving another acknowledge signal from the 24C08B/16B the master device will transmit the data word to be written into the addressed memory location. The 24C08B/16B acknowledges again and the master generates a stop condition. This initiates the internal write cycle, and during this time the 24C08B/16B will not generate acknowledge signals (Figure 4-1).
4.2
Page Write
FIGURE 3-2:
START
CONTROL BYTE ALLOCATION
READ/WRITE
SLAVE ADDRESS
R/W
A
1
0
1
0
B2
B1
B0
The write control byte, word address and the first data byte are transmitted to the 24C08B/16B in the same way as in a byte write. But instead of generating a stop condition the master transmits up to 16 data bytes to the 24C08B/16B which are temporarily stored in the onchip page buffer and will be written into the memory after the master has transmitted a stop condition. After the receipt of each word, the four lower order address pointer bits are internally incremented by one. The higher order seven bits of the word address remains constant. If the master should transmit more than 16 words prior to generating the stop condition, the address counter will roll over and the previously received data will be overwritten. As with the byte write operation, once the stop condition is received an internal write cycle will begin (Figure 4-2).
FIGURE 4-1:
BUS ACTIVITY MASTER
BYTE WRITE
S T A R T CONTROL BYTE WORD ADDRESS DATA S T O P
SDA LINE
S
A C K A C K A C K
P
BUS ACTIVITY
FIGURE 4-2:
BUS ACTIVITY MASTER
PAGE WRITE
S T A R T CONTROL BYTE WORD ADDRESS (n) DATA n DATA n + 1 DATA n + 15 S T O P
SDA LINE BUS ACTIVITY
S
A C K A C K A C K A C K A C K
P
© 1996 Microchip Technology Inc.
DS21081D-page 5
|
|
