|Category||Power Management => AC-DC Controllers/Converters => Bridge Rectifiers|
|Description||1.5 Amp Single Phase Bridge Rectifier 50 to 1000v|
|Datasheet||Download W005M-10M datasheet
Low Profile Package Any Mounting Position Silver Plated Copper Leads Surge Overload Rating Of 50 Amps
Average Forward Current Peak Forward Surge Current Maximum Forward Voltage Drop Per Element IF(AV) IFSM 25°C 8.3ms, half sine
Maximum DC Reverse Current = 25°C Rated DC Blocking = 100°C Voltage *Pulse test: Pulse width 300 µsec, Duty cycle 1%
Figure 1 Typical Forward Characteristics Amps Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Forward Derating Curve Amps.6 10.3 Single Phase, Half Wave 60Hz Resistive or Inductive Load °C Average Forward Rectified Current - Amperes versus Ambient Temperature - °C Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles 60Hz - Cycles Instantaneous Reverse Leakage Current - MicroAmperes versus Percent Of Rated Peak Reverse Voltage - Volts Amps.1.06.04.02.01.006.004.002.001 TJ=25°C Figure 2 Typical Reverse Characteristics
|Some Part number from the same manufacture Microsemi Corporation|
|X21100B1B1 Single Phase Bridge, Package : See_factory|
|X2190B1B1 Single Phase Bridge|
|X2190Z1B1 3 Phase Bridge|
|X34100B1B1 Single Phase Bridge, Package : See_factory|
BQ24004PWP : ti BQ24004, Li-ion Linear (8.2V & 8.4V) Charge Management ic For Two-cell Apps W/integrated Fet, One Led.
BQ4017YMC-70 : NVSRAM Power Management. ti BQ4017Y, 2048Kx8 Nonvolatile SRAM, 10% Voltage Tolerance.
FAN4041DI : Adjustable, 1% Tolerance Precision Micropower Shunt Reference. Adjustable shunt reference Tolerances +0.5% (25°C) Low output noise Low temperature coefficient to 100 ppm/°C max Small packages Extended operating current range The FAN4041 adjustable precision shunt references are ideal for space- and cost-sensitive applications. They are available with output voltage tolerances of 0.5% and 1%. They also have excellent.
LT117A : Adjustable. Positive Adjustable Regulator.
MB3793-45 : Regulator. Bipolar Power Voltage Monitoring ic With Watchdog Timer. The is an integrated circuit to monitor power voltage; it incorporates a watchdog timer. A reset signal is output when the power is cut or falls abruptly. When the power recovers normally after resetting, a power-on reset signal is output to microprocessor units (MPUs). An internal watchdog timer with two inputs for system operation diagnosis can provide.
PT7701A : Plug-in Power Solutions->Non-Isolated->Single Posi. ti PT7701, 2V to 3.5V 15A 5V-Input 'Big Hammer' Programmable Isr.
SC1185 : Switcher/Linear Regulators. Programmable Synchronous DC/DC Converter, Dual LDO Controller.
TA82553F : Sensing Circuit. G-force Sensor Amplifier ic.
TPS76030DBVR : ti TPS76030, Low-power 50-mA Low-dropout (LDO) Regulator. 50-mA Low-Dropout Regulator Fixed Output Voltage Options: 3.2 V, and 3 V Dropout Typically 50 mA Thermal Protection Less Than 1-µA Quiescent Current in Shutdown to 125°C Operating Junction Temperature Range 5-Pin SOT-23 Package ESD Protection Verified 1.5 kV Human Body Model (HBM) per MIL-STD-883C The a 50 mA, low dropout (LDO) voltage regulator designed.
TPS76133 : . 100-mA Low-Dropout Regulator Fixed Output Voltage Options: 3.2 V, and 3 V Dropout Typically at 100-mA Thermal Protection Less Than 1 µA Quiescent Current in Shutdown to 125°C Operating Junction Temperature Range 5-Pin SOT-23 (DBV) Package ESD Protection Verified 1.5 KV Human Body Model (HBM) per MIL-STD-883C The a 100 mA, low dropout (LDO) voltage regulator.
X80142 : Hotswap & Power Sequencers. Voltage Supervisor/sequencerquad Programmable Time Delay With Local/remote Voltage Monitors.
LT3477 : 3A, DC/DC Converter with Dual Rail-to-Rail Current Sense The LT®3477 is a current mode, 3A DC/DC step-up converter with dual rail-to-rail current sense amplifiers and an internal 3A, 42V switch. It combines a traditional voltage feedback loop and two unique current feedback loops to operate as a constant-current, constant-voltage source. Both current.
PTD08A020W : 20A, 4.75V To 14V, Non-Isolated, Digital PowerTrain Module The PTD08A020W is a high-performance 20-A rated, non-isolated digital PowerTrain module. This module is the power conversion section of a digital power system which incorporates TI\'s UCD7230 MOSFET driver IC. The PTD08A020W must be used in conjunction with a digital power controller such as the UCD9240.
TLV810S : 3-Pin Voltage Supervisor With Active-High, Push-Pull Reset The TLV810 family of supervisory circuits provides circuit initialization and timing supervision, primarily for DSPs and processor-based systems. During power-on, RESET is asserted when the supply voltage (VDD) becomes higher than 1.1 V. Thereafter, the supervisory circuit monitors VDD and keeps.
PT7M7811M : µ µ µ µ µP Supervisor Circuits The PT7M7xxx family microprocessor (µP) supervisory circuits are targeted to improve reliability and accuracy of power-supply circuitry in µP systems. These devices reduce the complexity and number of components required to monitor power-supply and battery functions..