|
|
Part: MF6256M-02BJXX
Category:
Memory
-> Flash
Description: 2.5 Flash Drive
Company: Mitsubishi Electronics America, Inc.
Datasheet: Download MF6256M-02BJXX datasheet File size : 700 kB
Request For quote: Find where to buy MF6256M-02BJXX
Datasheet text preview:
MITSUBISHI STORAGE CARD
Preliminary
FLASH DRIVES
2.5" Flash Drive
Connector Type
MF6128M-02BJ x x MF6256M-02BJ x x MF6512M-02BJ x x MF6640M-02BJ x x MF601G2-02BJ x x
IDE ATA 44-pin
DESCRIPTION
Mitsubishi's Flash Drives provide large memory capacities on a device approximately the size of a 2.5" IDE Type Hard Disk (101.85mm(L) × 69.85mm (W) × 8.47mm (T)). Available in 128MB, 256MB, 512MB, 640MB and 1.2GB capacities.
FEATURES
· 2.5", IDE ATA 44-pin · Single 5V Supply · Up to 1.2GB maximum · Nonvolatile, No Batteries Required · High reliability based on internal ECC function · Fast read/write performance
Read: 5MB/s(max.) The others = 3.0MB/s(max.) Write: 128MB card = 2.0MB/s(max.)
· Multiword DMA commands supported. · 100,000 program/erase cycles
APPLICATIONS
· Computers · Data Communication · Office Automation · Industrial · Consumer
PRODUCT LIST
Memory capacity (Bytes) MF6128M-02AJxx MF6256M-02AJxx MF6512M-02AJxx MF6640M-02AJxx MF601G2-02AJxx 128,057,344 257,163,264 515,579,904 640,475,136 1,219,534,848 Data Bus width(bits) Memory 256Mbit Flash x 4 256Mbit Flash x 8 256Mbit Flash x 16 256Mbit Flash x 20 256Mbit Flash x 40 Cylinder 977 981 999 1241 2363 Head 8 16 16 16 16 Sector 32 32 63 63 63 Out line
8/16
2.5" IDE
Oct.2000.Rev.0.3 MITSUBISHI ELECTRIC 1/18
MITSUBISHI STORAGE CARD
Preliminary MF6XXXX-02BJXX series
FLASH DRIVES PIN ASSIGNMENT
Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 Signal RESET# DD7 DD6 DD5 DD4 DD3 DD2 DD1 DD0 GND DMARQ DIOW# RIOR# IORDY DMACK# INTRQ DA1 DA0 CS0# DASP# VDD GND I/O I I/O I/O I/O I/O I/O I/O I/O I/O O I I O I O I I I I/O Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 Signal GND DD8 DD9 DD10 DD11 DD12 DD13 DD14 DD15 (keypin) GND GND GND CSEL GND IOCS16# PDIAG# DA2 CS1# GND VDD GND I/O I/O I/O I/O I/O I/O I/O I/O I/O I O I/O I I -
Oct.2000. Rev. 0.3 MITSUBISHI ELECTRIC 2/18
MITSUBISHI STORAGE CARD
Preliminary MF6XXXX-02BJXX series
Master/Slave/Cable Select Configuration (1) Master(or single) [Default] If all of pins A, B, C, D are Open, the drive is a Master.
43 1 CA
FLASH DRIVES
······················ ············ ·········
44 20 2
·· ··
DB
(2) Slave If pins C, D are open and jumper position A-B is used, the drive is a Slave.
43 1 CA
······················ ············ ·········
44 20 2
·· ··
DB
(3) Cable Select [Default] If jumper position D-B is used and pins C, A is open, Master/Slave setting is determined by the condition of CSEL signal from the host.
43 1 CA
······················ ············ ·········
44 20 2
·· ··
DB
Oct.2000. Rev. 0.3 MITSUBISHI ELECTRIC 3/18
Others parts begin by mf
|
|
|
